Raex YR2118B User manual

Wireless transmitter instruction
Specification
Model
Frequency
Mould
Battery
Channel
Channel
Channel
Choose
Right
Open
Stop
Close
Up tilt
/75%
Horizontal
position
/50%
Down tilt
/25%
Channel
Choose
Left
Channel
setting
[stop]+[up/open] [stop]+[down/close]
Press 5 seconds, press [programming
button] to confirm, switch on touch
cotnrol.
Press 5 seconds, press [programming
button] to confirm, switch off touch
cotnrol.
Set remote control channel
Enter into programming Choose channels
Press programming button for 3 sec-
onds,until LED light on.
Press[Channel Choose Left] (or [ Channel
Choose Right]) button to choose the
needed channel.
Send the current channel code Confirmation
Press[Channel Setting] button on the
back of transmitter till the indicator
light of the motor sparkles.
Press[Setting] button again to confirm
the operation. The remote channel is
set.
Delete remote control channels
Enter into setting codes status Delete remote control channels
Press[Setting]button 3 seconds to
indicate till the indicator light on.
Press[Setting] buttton again for 7 sec-
onds till the light off. Channel deleting
is completed.
4
Warranty
Series motor carry a three years warranty from the date of invoice.Factitious
damage and dismantle are exclusive of wattantly.

LED light
Channel,LED 1,channel 1,LED 2,channel 2….LED 6,Channel 6,
LED on means signal transmit
Choose the previous channel
Presss[Chennel selection-left],the current channel LED light will
be on,Press[Chennel selection left]within 3 seconds,press channel 6.
channel 5,channel 4 accordingly.Channel 3-channel 2,channel 1…
channel 6 in cyclic selection,the LED light will be off if no any
operation within 3 seconds.
Choose the next channel
Press[Chennel selection-right]the current channel LED light will
be on,Press[Chennel selection-right]within 3 seconds,press channel
1.channel 2,channel 3 accordingly.
Channel 3-channel 2,channel 1… channel 6 in circle selection, the
LED light will be off if no any operation within 3 seconds.
[Up/Open] [Stop]
open the curtains.Stop the curtain.
[Down/Close] [Up Tilting/75%]
Close the curtains. Short time press,up tilting, press 1.5
second, move to IP1 75% limit position.
[Horizontal Position/50%] [Down Tilting/25%]
Press tilt to horizontal position,press
1.5 second,move to IP3 50% limit
position.
Presstilt to Down tilting,press 1.5 second,
move to IP2 25% limit position.
[Channel Choose Left]+[Stop] [Channel Setting]+[Up/Open]
Direction change,After entering into
programming, press Programming
Button to confirm.
Press 5 seconds,enter into [Up/Open],
limit setting,move to position you like,
press Programming Button to confirm.
[Channel Setting]+[Stop] [Channel Setting]+[Down/Close]
Press 5 seconds, delete limit. Press 5 seconds,enter into [Down/Close]
limit setting, move to the position you like,
press Programming Button to confirm.
Button function
⑤ ⑥
[Channel Setting]
Open the case, press the button for
programming.
⑦
Combination button
The specific operation of combination keys is as follows
+
5S
5S
+
5S 5S + 5S
5S
[Up/Open]+[Down/Close] [Channel Setting]+[Up Tilting/75%]
External control mode,Press up and
down button and then confirm by
programming button.
Press programming button and IP1 button.
[channel Setting]+[Horizontal
Tilting/50%]
[Channel Setting]+[Down Tilting
/25%]
Quick press to IP3,long press for 50%
limit position.
Quick press to IP2, long press for 25%
limit postion
+
+ +
Remark
1.All button’s function should be work with motor/controller
2.Choose current channel for all function setting
3.Hold programming button when press up/down button for limit setting
2 3
1.5S
1.5S
1.5S