Ranger Products RFJ-3000AL User manual

PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO
INSTALLATION AND OPERATION. BY PROCEEDING YOU AGREE THAT
YOU FULLY UNDERSTAND AND COMPREHEND THE FULL CONTENTS OF
THIS MANUAL. FORWARD THIS MANUAL TO ALL OPERATORS. FAILURE TO
OPERATE THIS EQUIPMENT AS DIRECTED MAY CAUSE INJURY OR DEATH.
REV A 10-26-09
INSTALLATION AND OPERATION MANUAL
SHIPPING DAMAGE CLAIMS
When this equipment is shipped, title passes
to the purchaser upon receipt from the carrier.
Consequently, claims for the material damaged in
shipment must be made by the purchaser against the
transportation company at the time shipment is received.
BE SAFE
Ranger™ Floor Jacks are designed and built
with safety in mind. However, proper training and
thoughtful operation on the part of the operator can
increase your overall safety. DO NOT operate or
repair this equipment without reading this manual
and the important safety instructions shown inside.
1645 Lemonwood Dr.
Santa Paula, CA. 93060, USA
Tel: [phone]
Toll Free: 1-800-253-2363
Fax: [phone]
www.rangerproducts.com
Aluminium Racing Jack
Model: RFJ-3000AL
REV A

2
WARRANTY POLICY
Ranger Products™ are backed by over 35 years of
manufacturing experience. Every Floor Jack
bearing the Ranger™ name is sold with the
following warranty.
Each Ranger Product™ is warranted to be free
from defects in workmanship and material for a
period of one year from the date of shipment
provided that a written claim for such defect is
made within that time.
This warranty does not cover damage or defects
caused by carelessness of the operator, misuse,
abuse or abnormal use which in any way impairs the
proper functioning of the equipment or by the use or
addition of parts not manufactured by Ranger
Products™ or its suppliers.
THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF
ANY AND ALL OTHER WARRANTIES EXPRESSED
OR IMPLIED INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE.
If your Ranger Products™ machine is not functioning
properly, call your Ranger Products™ dealer immediately.
On some occasions, an independent contractor may be
hired to do the repairs. Within the warranty period, a
customer should not hire his own contractor unless it is
authorized in writing by Ranger Products™.
If it is necessary to return equipment for repairs, your
dealer will so advise you. When returning equipment for
repairs, see that machines are properly crated and
protected, and prepay transportation.
Defective parts replaced at no charge must be returned
to your dealer or Ranger Products™ within 60 days of the
date that the replacement parts are shipped; otherwise,
you must pay for the replacement parts at the current
selling price.
SHIPPING DAMAGE
If any damage is found, notify your carrier
immediately and save all packaging materials for the
carrier’s inspector to examine. Failure to promptly
report damage could result in denial of your claim.
A trucking company’s procedure for handling damage is
as follows:
1. Immediately send out an inspector. An inspection
report is filled out on the spot, a copy of which is
given to the customer.
2. The customer has to call the carrier to request a
claim form.
3. The customer mails in the claim form.
4. The claim usually takes two (2) months to process.
If a unit is seriously damaged, your Ranger Products
dealer may be able to intervene, requesting that the
damaged unit be returned and a new unit delivered.
IMPORTANT SAFETY TIPS
ALWAYS MAINTAIN A CLEAN WORK AREA.
KEEP VISITORS AND ESPECIALLY
CHILDREN AWAY FROM WORK AREA.
THIS FLOOR JACK IS TO BE OPERATED BY
PROPERLY TRAINED PERSONNEL ONLY.
OPERATION BY UNTRAINED
PERSONNEL MAY RESULT IN INJURY
AND /OR PROPERTY DAMAGE.
For Parts Or Service Contact:
BendPak Inc. / Ranger Products
1645 Lemonwood Dr.
Santa Paula, CA. 93060
Tel: [phone]
Toll Free: 1-800-253-2363
Fax: [phone]
www.bendpak.com
www.rangerproducts.com

3
THIS OPERATING MANUAL CONTAINS
IMPORTANT DETAILS CONCERNING THE
SAFE OPERATION OF THIS TOOL. THE
USER MUST READ AND UNDERSTAND
THESE DETAILS BEFORE ANY USE OF THE
TOOL. THIS MANUAL MUST BE RETAINED
FOR FUTURE REFERENCE.
OWNER/OPERATOR
RESPONSIBILITY:
The owner and/or operator shall study the product
instructions and retain them for future reference.
The owner and/or operator shall have an understanding
of the product operating instructions and warnings before
operating the jack.
Warning information shall be emphasized and
understood. If the operator is not fluent in English, the
product instructions and warnings shall be read to and
discussed with the operator in the operator’s native
language by the purchaser/ owner or his designee,
making sure that the operator comprehends its contents.
INSPECTION
Visual inspection should be made before each use of the
jack. This inspection should check for abnormal
conditions such as cracked welds, leaks, and damaged,
loose or missing parts.
Any jack that appears to be damaged in any way, is found
to be worn or operated abnormally, must be removed
from service immediately.
Any jack that operates abnormally shall be removed from
service until repaired by a qualified repair service center.
If the jack is accidentally subjected to an abnormal load
or shock, it must be taken out of service immediately and
be inspected by a qualified repair or service center.
It is recommended that an annual inspection is performed
on the jack and that any damaged or worn parts, decals
or warning labels be replaced with manufacturer’s
specified parts.
ALTERATIONS
Because of potential hazards associated with this type of
equipment, no alterations shall be made to the product.
FOR YOUR SAFETY AND TO PREVENT INJURY:
Use Service Jack for lifting purposes ONLY.
Always support vehicle with jack stands.
WARNING!
THIS IS A LIFTING DEVICE ONLY. DO NOT MOVE OR
DOLLY THE VEHICLE WHILE ON THE JACK.
IMMEDIATELY AFTER LIFTING, SUPPORT THE
VEHICLE WITH APPROPRIATE MEANS.
DO NOT EXCEED RATED CAPACITY.
OVERLOADING CAN CAUSE DAMAGE TO
OR FAILURE OF THE JACK.
LIFT ONLY ON AREAS OF THE VEHICLE AS
SPECIFIED BY THE VEHICLE MANUFACTURER.
KEEP HANDS AND BODY CLEAR OF ALL PINCH
POINTS.
CENTER LOAD ON SADDLE PRIOR TO LIFTING.
OFF-CENTER LOADS MAY CAUSE DAMAGE TO
JACK, LOSS OF LOAD, PROPERTY DAMAGE,
PERSONAL OR FATAL INJURY.
THIS JACK IS DESIGNED FOR USE ONLY ON HARD
LEVEL SURFACES CAPABLE OF SUSTAINING THE
LOAD. USE ON OTHER THAN HARD LEVEL
SURFACES CAN RESULT IN JACK INSTABILITY AND
POSSIBLE LOSS OF LOAD.
NO ALTERATIONS TO THE JACK SHALL BE MADE.
READ, STUDY AND UNDERSTAND THE OPERATING
MANUAL PACKED WITH THIS JACK BEFORE
OPERATING.
FAILURE TO HEED THESE WARNINGS MAY RESULT
IN LOSS OF LOAD, DAMAGE TO JACK, AND/OR
FAILURE RESULTING IN PROPERTY DAMAGE,
PERSONAL OR FATAL INJURY.

4
ASSEMBLY INSTRUCTIONS
1. Assemble Upper and Lower Handle, insert into Handle
Socket and tighten Bolt.
OPERATING INSTRUCTIONS
BEFORE USE:
Air may become trapped in the hydraulic system during
transit. To purge air:
1. Open release valve by twisting Handle counter
clockwise.
2. Pump Handle rapidly 4-6 full strokes. This will expel air
that may have entered oil passages during transit.
3. Close release valve by twisting Handle clockwise and
pump handle.
4. If lift arm is raised, jack is ready for use. If not, repeat
this procedure.
BEFORE ATTEMPTING TO RAISE ANY VEHICLE,
CHECK VEHICLE SERVICE MANUAL FOR
RECOMMENDED LIFTING POINTS.
OPERATION:
1. To Raise Load: Close release valve tightly (by
twisting Handle clockwise. DO NOT OVERTIGHTEN.
Position jack under load so that saddle will contact load
firmly and load is centered so it cannot slip. Operate jack
handle until saddle approaches the load. Once again,
check to see that saddle is correctly positioned. Raise
load to desired height. Place jack stands of appropriate
capacity under the vehicle.
DO NOT CRAWL UNDER VEHICLE WHILE
LIFTING VEHICLE OR PLACING
OR REMOVING JACK STANDS!
Place jack stands at vehicle manufacturer’s
recommended lift areas that provide stable support for
the raised Vehicle. Once jack stands are positioned, open
the release valve VERY SLOWLY (by twisting the Handle
counter clockwise.)
Lower the load to rest on the jack stands. Then, make
sure that the release valve on the jack is closed tightly
(twist the Handle clockwise).
2. To lower load:
Re-check to make sure release valve is tightly closed
(twist the Handle clockwise). Then, operate the jack
handle until the load is raised enough to remove the jack
stands.
DANGER!
DO NOT CRAWL UNDER VEHICLE WHILE LIFTING
VEHICLE OR REMOVING THE JACK STANDS!
Once jack stands are removed, open release valve very
slowly to lower the vehicle (twist the Handle counter
clockwise). Lower jack completely so that the vehicle is
securely resting on the ground and that jack no longer
makes contact with vehicle.
CAUTION!
Keep hands or feet away from the
hinge mechanism of the jack.
MAINTENANCE
When adding or replacing hydraulic fluid, always use a
quality hydraulic fluid. DO NOT use brake fluid, alcohol,
detergent motor oil, dirty oil or any fluid other than quality
hydraulic fluid. Improper fluids can cause internal
damage to the jack and improper or unsafe operation.
ADDING HYDRAULIC FLUID
With the saddle fully lowered and the jack on level
ground, remove the filler screw. Hydraulic fluid should
be filled to the level of the filler screw hole. If the level is
below this hole, add hydraulic fluid as needed.
LUBRICATION
All moving joints require lubrication often. Lightly grease
saddle post and saddle bottom. Remove handle and
grease the lower end of handle where it rotates in the
handle socket. Oil all lift arm linkages, front wheels and
rear casters.

5
PROBLEM ACTION
1. Unit will not lift load Purge air from hydraulic system by following procedure
under OPERATING INSTRUCTIONS.
2. Unit will not sustain load or feels “spongy” under load. Purge air from hydraulic system as above.
3. Unit will not lift to full height. Purge air from hydraulic system as above. Check to be sure
oil level is not too high or low.
4. Unit will not lower completely. Check oil level. Make sure not overfilled.
5. Handle tends to raise up while the unit is under load. Pump the handle rapidly several times to push oil past ball
valves in power unit.
6. Unit still does not operate. Contact Parts & Warranty Department.
SPECIFICATIONS
FEATURES
DESCRIPTION
TROUBLESHOOTING
Maximum Capacity 3,000 lbs / 1361 kg.
Maximum Saddle Height 17.75” / 451mm
Minimum Saddle Height 3.5” / 89mm
Overall width 11.75” / 298
Chassis Length 24” / 610mm
Shipping Weight 42 lbs. / 19kgs.
Shipping Dimensions 29” x 13”x 7” / 737 x 330 x 178mm
 Lightweight for easy portability
 Aircraft grade billet aluminum design
 Low profile single piece front roller
 Oversized knurled aluminum handle
 Fast 4-pump operation gets cars up quick
 Reaches full lifting height with just four pumps
 Dual-plunger pump assembly
 Roller-cam plungers and u-joint release
 Alloy-plated ram
 Double-sealed hydraulics for longer service life
 Built-in safety overload valve
The Ranger model RFJ-3000AL Aluminum Racing Jack is made of the strongest aircraft alloy aluminum available. Not
only does it weigh in at a feather-light 39 lbs., but it gets any racecar or hotrod a full 17-3/4” off the ground in just four
pumps of its knurled aluminum handle. With a low 3-1/2” profile front-roller, the RFJ-3000AL is perfect for working on
ground-hugging, low ground-clearance performance vehicles.

6
PARTS BREAKDOWN
PARTS BREAKDOWN

7
For Parts Or Service
Contact:
BendPak Inc. / Ranger Products
1645 Lemonwood Dr.
Santa Paula, CA. 93060
Tel: [phone]
Toll Free: 1-800-253-2363
Fax: [phone]
www.bendpak.com
www.rangerproducts.com