Rapid EBR-LCM-DALIG64 User manual

Overview
The EBR-LCM-DALIG64 is a Rapid lighting control module
designed for controlling addressable DALI devices such as
fluorescent or LED lighting ballasts. With 3 pluggable
outputs the full range of 64 DALI addresses can be
achieved. These ports share a relay providing a switched
live output and a second relay for emergency test. The 4th
output is a volt free contact to control external devices.
This LCM also has a total of 11 switch inputs. 6 in the
wiring compartment with screw terminals and 7 via an RJ45
port.
Used in conjunction with our range of DALI presence
detectors a single DALI cable can be run to digitally control
all the lighting and power the sensors. This saves time and
money on additional specialist cable. It is ideal for chilled
beam, continuous run lighting, and core areas.
Please speak to our technical team for further information.
Features
Pluggable DALI lighting control module
EBR-LCM-DALIG64
Wiring compartment
Within the wiring compartment there are the following
connections.
 Mains, including a Permanent Live used to feed the
emergency test relay.
 Low Voltage connections
 6 x ELV inputs. (Inputs 1-5 & 11)
 2 x Rapid network CAN ports
Pluggable DALI connections
Three 6 pole GST style ports with DALI bus connection and
shared 10A relays for a switched output and 6A emergency
test.
Volt free output port
6A 230VAC Voltage free contact. Used to switch external
peripherals, such as HVAC and BMS systems.
RJ45 ports
At the end of the unit there are 5 RJ45 ports.
 2 x power and Rapid network CAN ports
 2 x Rapid network CAN ports
 1 x ELV switch input port (7 inputs plus common).
Inputs 5-11.
Front features
Wiring
compartment
Product Guide
Pluggable DALI
connections
Volt free
output port
RJ45 portsProgramming window
which covers...
IR Receiver
Status LED

2
Installation
Installation
System wiring example
Rapid Area Controller
Rapid PIR
Rapid Scene plates
Standard light switches
3 core SELV DALI bus
Rapid Microwave
DALI light fitting with DALI
emergency inverter
EBR-MINPIR-DALI
Mini PIR integrated into lighting run
DALI light fitting
EBR-CPIR-DALI
CAT 5 cable CAT 5 cable
Rapid DALI gateway
Channel for channel nuts (zebs)
Removable gland plate with
3 x Ø20mm knockouts
3 x Ø20mm knockouts for rear
cable entry
4 x key slots to accept M6 (1/4”)
fixings
BESA box fixings
Warning. This device works at mains voltage. Be sure to take care when working with electricity.
 The box should be fixed on a smooth, flat surface or using drop rod fixings attached to channel nuts.
 Ensure that there is easy access to the wiring compartment and all connectors once the box is in-situ.

3
DALI port connections / Lead colours
DA+ Red
DA - White
Switched Permanent Live Black
Neutral Blue
Earth Green / Yellow
Switched Live Brown
Small
cables
Large
cables
Cable clamps
Wiring
RJ45 ports
VFC port connections / Lead colours
VFC –N/O Red
VFC –Common White
Permanent Live Black
Neutral Blue
Earth Green / Yellow
Live Brown
Live
Neutral
Earth
Permanent
Live
6 ELV switch
input ports
2 CAN ports
Detector and ballast combinations for 200mA supply.
This assumes that the sensor LEDs are all on, and the sensor is receiving IR communication.
 4 detectors and up to 64 ballasts
 5 detectors and up to 55 ballasts
 6 detectors and up to 44 ballasts
 7 detectors and up to 33 ballasts
 8 detectors and up to 22 ballasts
 9 detectors and up to 12 ballasts
 10 detectors and up to 2 ballasts
In most realistic scenarios, only one LED is on at a time and only one detector is receiving IR; guidance changes to.
 10 detectors up to 50 ballasts
 8 detectors up to 64 ballasts
To use a higher number of detectors then ensure only one detector has walk test enabled per DALI bus.
DALI bus loading
Port 1
7 x switch inputs
Inputs C, 11, 10, 9, 8, 7, 6, 5
Port 2 & 3
CAN
Port 4 & 5
CAN + power

4
Due to our policy of continual product improvement CP Electronics reserves the right to alter the specification of this product without prior notice.
Dimensions See diagrams opposite
Weight 0.45kg
Supply Voltage 220-240VAC
Frequency 50Hz
Relay rating Switched live 10A
Switched permanent live 6A
Volt free output (VFC) 6A
Terminal Capacity Mains - 4mm2in wiring
compartment
Switched inputs and CAN -
2.5mm2in wiring compartment
DALI Voltage 16VDC via DALI
DALI Output Current 250mA (maximum)
DALI bus Cannot be considered as SELV
since DALI, ballasts only offer
basic insulation, therefore all
devices on the DALI bus must be
wired as if carrying mains
potential.
Temperature -10ºC to 35ºC
Humidity 5 to 95% non-condensing
Material (casing) Flame retardant ABS and PC/ABS
Classifications Insulation Class II
Purpose Operating control
Construction Independently mounted
control for surface
mounting
Type of action Type 1.B action
micro disconnection
Software class Class A
Pollution Degree 2
Compliance EMC-2004/108/EC
LVD-2006/95/EC
Important
For lighting purposes only with suitable circuit
protection. For fixed wiring only.
Technical data
C.P. Electronics Ltd
Brent Crescent
London
NW10 7XR
United Kingdom
Tel: + 44 (0) 333 900 0671
Fax: + 44 (0) 333 900 0674
www.cpelectronics.co.uk
[e-mail]
Ref: #WD584 Issue 4
FM 45789 EMS 534520
IMPORTANT NOTICE!
This device should be installed by a qualified electrician in
accordance with the latest edition of the IEE Wiring
Regulations and any applicable Building Regulations.
Part numbers
Part number Description
Control module EBR-LCM-DALIG64 Pluggable DALI lighting control module
Accessories UNLCDHS Universal LCD programming handset
202mm
150mm
146mm 127mm
Fixing points
M6 (1/4”)
Height - allow 150mm for total height of unit (including
connectors and cable)