RASHA PROFESSIONAL HEX V12 Wireless User manual

Rasha Professional A/S 375 W Esplanade Ave. San Jacinto, CA 92583 | 951-654-3585
rashaprofessional .com | [email protected] Rev. 101615
1
Sku# Model#
WARNING!
TO PREVENT OR REDUCE THE RISK OF ELECTRICAL SHOCK OR FIRE, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
CAUTION!
THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT
ANY REPAIRS YOURSELF, DOING SO WILL VOID YOUR MANUFACTURES
WARRANTY. IN THE UNLIKELY EVENT YOUR UNIT MAY REQUIRE SERVICE
PLEASE CONTACT RASHA PROFESSIONAL A/S
INSTRUCTION MANUAL
RASHA
WIRELESS
HEX V12

Rasha Professional A/S 375 W Esplanade Ave. San Jacinto, CA 92583 | 951-654-3585
rashaprofessional .com | [email protected] Rev. 101615
2
Features:
• RGBAW (6 in 1)-Colors Mixing / Single RGBAW+UV Colors
• Electronic Dimming 0-100%
• Strobe(0-100%)
• Built in Microphone
• DMX-512 protocol
• 3-Pin DMX Connection
• 7/12 DMX Modes:
• DMX 2.4G Receiver Built -In
Thank you for purchasing the Rasha®Hex V12 Wireless. Every Rasha®Hex V12
Wireless has been thoroughly tested and has been shipped in perfect operating
condition. Carefully check the shipping carton for damage that may have
occurred during shipping. If the carton appears to be damaged, carefully inspect
yourxtureforanydamageandbesureallaccessoriesnecessarytooperate
the unit has arrived intact. In the case damage has been found or parts are
missing, please contact our toll customer support number for further instructions
within24hoursofreceivingyourxture.
Please Contact your dealer for any warranty issues.

Rasha Professional A/S 375 W Esplanade Ave. San Jacinto, CA 92583 | 951-654-3585
rashaprofessional .com | [email protected] Rev. 101615
3
This page is left intentionally blank

Rasha Professional A/S 375 W Esplanade Ave. San Jacinto, CA 92583 | 951-654-3585
rashaprofessional .com | [email protected] Rev. 101615
4
The Rasha®Hex V12 Wireless is part of a our pursuit to create high quality
intelligent lighting. The Rasha®Hex V12 Wireless isaDMXintelligentThisxture
canbeusedinastandalonemodeorconnectedinaMaster/Slaveconguration.
The Rasha®Hex V12 Wireless hasveoperatingmodes:
1. Sound Active mode
2. Auto mode (White+ Amber)
3. DMX control mode.
4. ColorStrobeEect
5. Color Change, (Color Dimmer, Color Jump/Gradually auto change)
To optimize the performance of this product, please read these operating
instructions carefully to familiarize yourself with the basic operations of this unit.
These instructions contain important safety information regarding the use
and maintenance of this unit. Please keep this manual with the unit, for future
reference.
Customer Support:
Rasha provides a customer support line, to provide set up help and to answer
any question should you encounter problems during your set up or initial
operation. You may also visit us on the web at Rashaprofessiona.com for any
comments or suggestions.
Service Hours are Monday through Friday 8:00 a.m. to 5:30 p.m.
PacicStandardTime.
Voice: [phone]
E-mail: [email protected]

Rasha Professional A/S 375 W Esplanade Ave. San Jacinto, CA 92583 | 951-654-3585
rashaprofessional .com | [email protected] Rev. 101615
5
• To reduce the risk of electrical shock or re, do not expose this unit rain or
moisture.
• Do not attempt to operate this unit if the power cord has been frayed or
broken.
• Do not attempt to remove or break o the ground prong from the electrical
cord. This prong is used to reduce the risk of electrical shock and re in
case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. This will Void your
Warranyt
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount xture in well ventilated area. (Allow about 6” or
15cm between this device and a wall.
• Do not attempt to operate this unit if it becomes damaged.
• This unit is intended for indoor use only, use of this product outdoors voids
all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to be
walked on or pinched by items placed upon or against them, paying
particular attention to the point they exit from the unit.
Cleaning
• The xture should be cleaned only as recommended by the manufacturer.
Heat
• Fixture should be away from heat sources (including ampliers) that
produce heat.
The xture should be serviced by qualied service personnel when:
1. The power-supply cord or the plug has been damaged.
2. Objects have fallen, or liquid has been spilled into the appliance.
3. The xture has been exposed to rain or water.
4. The xture des not appear to operate normally or exhibits a marked
change in performance.
Safety Precautions

Rasha Professional A/S 375 W Esplanade Ave. San Jacinto, CA 92583 | 951-654-3585
rashaprofessional .com | [email protected] Rev. 101615
6
1
2
3
1
2
3
DMX +
COMMON
Figure 4
DMX -
DMX512 OUT
3-PIN XLR DMX512 IN 3-PIN XLR
XLR Male Socket XLR Pin Conguration
1 Ground 1 Ground
2 Cold 2 Cold Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 2 = Data True (Positve)
3 Hot 3 Hot
XLR Female Socket
Figure 3
Notice: Be sure to follow gures two and three when making your own cables.
Do not use the ground lug on the XLR connector. Do not connect the cable’s
shield conductor to the ground lug or allow the shield conductor to come in
contact with the XLR’s outer casing. Grounding the shield could cause a short
circuit and erratic behavior.
Special Note: Line Termination. When longer runs of cable are used, you
may need to use a terminator on the last unit to avoid erratic behavior. A
terminator is a 110-120 ohm 1/4 watt resistor which is connected between
pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is
inserted in the female XLR connector of the last unit in your daisy chain to
terminate the line. Using a cable terminator (Rasha part number R-DMX/T) will
decrease the possibilities of erratic behavior
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-512
data cables for DATA transmission in place of 3-pin. 5-pin DMX xtures may
be implemented in a 3-pin DMX line. When inserting standard 5-pin data
cables in to a 3-pin line a cable adaptor must be used, these adaptors are
readily available at most electric stores. The chart below details a proper cable
conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor 3-Pin XLR Female (Out) 5-Pin XLR Male (In)
Ground/Sheild Pin1 Pin1
Data Compliment (- signal) Pin 2 Pin 2
Data True (+ signal) Pin 3 Pin 3
Not Used Do Not Use
Not Used Do Not Use
1
2
3
Figure 5
Termination reduces signal erros and acoids
signal transmission problems and intreference. it
is always advisable to connect a DMX terminal.
(Resisantce 120 Ohm 1/4W) Between PIN 2
(DMX-) and PIN 3 (DMX+) of the last xture.
Set Up

Rasha Professional A/S 375 W Esplanade Ave. San Jacinto, CA 92583 | 951-654-3585
rashaprofessional .com | [email protected] Rev. 101615
7
Operating Instructions
UP and DOWN buttons to adjust intensity.
After you have adjusted the RGBAW colors to make your desired color you can
then activate strobing by pressing the SET UP button to enter the Flash (strobe)
mode.
Firmware Version
Rest to factory settings
Fixture DMX Address Setting
7-Channel DMX
12 channel DMX
Set xture to Slave Mode
Set Fixture to Master Mode
Receive the signal but do not transmit signal
Built In auto Color change
IR remote control activation
34 preset colors
Slow Color Change
Medium Color Change
Fast Color Change
Sound Activated
Color Customization
Dimmer Mode 1 - Linear
Dimmer Mode 2 - Squar Law
Dimmer Mode 3 - Inverse Square Law
Blackout Mode on
Blackout Mode off
LED Display on/off
Reverse Display
Red Color Test
Green Color Test
Blue Color Test
Amber Color Test
White Color Test
Ultra Violet Color Test
Full Color Test
Strobe Speed-slow (1) to fast (100) - ( mode
activation and choose color to display)

Rasha Professional A/S 375 W Esplanade Ave. San Jacinto, CA 92583 | 951-654-3585
rashaprofessional .com | [email protected] Rev. 101615
8
Operating Instuctions
DMX Mode Cont.
Display Buttons:
MENU DOWN UP ENTER
After initialization, the unit is ready for setting and working. Please see the following
table for setting information
This function will allow you to “ip” the LED display.
1. Plug the xture in and press the MENU button until “ ” is displayed. “
” and press ENTER for DMX Mode.
2. Press the SET UP button until “Test” is displayed. For testing the light
Default Running Mode:
This is a default running mode. When this mode is activated all modes will return to
their default settings.
1. Press the MENU button until “ ” ENTER- Press and press
ENTER for DMX Mode
2. Press the SET UP button until “ ” is displayed.
3. Press the UP and DOWN buttons simultaneously. Press the MODE button to
exit
4. Press – to choose Master or salve mode
5. Press – - for sound active mode.
6. Press - – AUTO to choose auto color mixing
7. Press - - to to set the customized color or hold
the Mode
Operating through a DMX controller gives the user the freedom to create their own
programs tailored to their own individual needs. This function also allows you to use
your xtures as spot lights. The Rasha®Hex V12 Wireless has 5/9 DMX Mode. (for
each modes’ DMX traits See below dmx chart).
1. This allows you to control individual xture traits with a standard DMX 512
controller.

Rasha Professional A/S 375 W Esplanade Ave. San Jacinto, CA 92583 | 951-654-3585
rashaprofessional .com | [email protected] Rev. 101615
9
Master-Slave Conguration:
This function will allows you to link units together to run in a Master-Slave
mode. In Master-Slave operation one unit will act as the controlling unit and the
others will react to the controlling unit’s built-in programs. Any unit can act as a
Master or as a Slave however, only one unit can be programmed to act as the
“Master.”
Master and salve connection setting without using the DMX controller
1. Daisy chain your units via the XLR connector or DMX cable on the rear
of the unit. Use standard XLR data cables to link your units together.
Remember that the Male XLR connector is the input and the Female XLR
connector is the output. The rst unit in the chain (master) will use the
female XLR connector only. The last unit in the chain will use the male XLR
connector only.
2. Set rst light at “ ” and rest of xtures on SL1 Mode. It means rst
xture will be the master xture which send same operating command to
other xtures of the network(we call those other xture on Slave mode or
Sl1 or Sl2)
3. After done this setting of No 2, now all xtures are connected and ready
to go or ready to get command of the rst xture or master xture. Now
you can set dierent operating modes, example: sound active, static color,
auto or fade. Once you set the modes at rst master unit other xtures
will start to project same the eect as master unit did. If light not stable in
static mode or custom mode be noted that light is salve mode, you have
set the light rst at master mode to stable in standalone built in color or
eect
Master and salve connection setting without using the DMX controller
1. Connect the DMX controller and Fixture by using the DMX cable. Link
other units with rst xture and rest of unit, set all xtures at Sl1 or Sl2
mode. Once you set the xture it will appear “A001” or “STBY” it means
now xture ready to go with DMX controllerconnector only.
Master-Slave Conguration

Rasha Professional A/S 375 W Esplanade Ave. San Jacinto, CA 92583 | 951-654-3585
rashaprofessional .com | [email protected] Rev. 101615
10
Operation:
Operating through an DMX controller gives the user the freedom to create
their own programs tailored to their own individual needs. Follow the directions
below to set your DMX Mode and address.
1. Before connecting to DMX controller, your xture has dierent DMX
channel modes; please select your desired mode by pressing the DMX
Mode button, then using the “Up” or “Down” buttons to scroll through the
DMX Channel Modes. Set the mode before you address the xture. See
the bottom of this page for the DMX modes.
2. After you have selected your mode, set the wireless DMX wireless
Note: When setting the DMX address each time a number is pressed a LED
color will glow, 3. now you may connect the xture via the XLR connections to
any standard DMX controller. Please see below pages for a detailed description
of the DMX modes, values, and traits.
DMX Control

Rasha Professional A/S 375 W Esplanade Ave. San Jacinto, CA 92583 | 951-654-3585
rashaprofessional .com | [email protected] Rev. 101615
11
Channel Value Description
CH1 0 No action
1-255 RED dimmer
CH2 0 No action
1-255 GREEN dimmer
CH3 0 No action
1-255 BLUE dimmer
CH4 0 No action
1-255 Amber( dimmer -Sharp
CH5 0 No action
1-255 White (0-255 white dimmer)
CH6 0 No Action
1-255 UV (0-255 UV dimmer)
CH7 0 No Action
1-255 Strobe
12 CH Mode
Channel Value Description
CH1 0No action(blackout)
1-255 RED dimmer--Bright
CH2 0No action (blackout)
1-255 GREEN dimmer--Bright
CH3 0No action (blackout)
1-255 BLUE dimmer--Bright
CH4 0No action (blackout)
1-255 Amber dimmer-Bright
CH5 0No action (blackout)
1-255 White Dimmer-Bright
CH6 0No action(blackout)
1-255 UV dimmer-Bright

Rasha Professional A/S 375 W Esplanade Ave. San Jacinto, CA 92583 | 951-654-3585
rashaprofessional .com | [email protected] Rev. 101615
12
CH7 0-8 No action (blackout) Preset color
8-15 Strobe from slow to fast
16-23 Pulse
24-30 Random
31-38
39-46
47-54
55-61
62-69
70-77
78-85
86-92
93-100
101-108
109-116
117-123
124-131
132-139
140-147
148-154
155-162
163-170
171-178
179-185
186-193
194-201
202-209
210-216
217-224
225-232
233-240
241-247
248-255

Rasha Professional A/S 375 W Esplanade Ave. San Jacinto, CA 92583 | 951-654-3585
rashaprofessional .com | [email protected] Rev. 101615
13
With this feature you can connect the xtures to one another using the IEC
input and output sockets. The quantity that can be connected is 33 xtures
maximum. After 33 xtures you will need to use a new power outlet. They must
be the same xtures. DO NOT mix xtures.
Disconnect the unit from its power source. Remove the power cord from the
unit. Once the cord has been removed, you will nd that the fuse holder is
located inside the power socket. Insert a at-head screw driver into the power
socket and gently pry out the fuse holder. Remove the bad fuse and replace
with a new one. The fuse holder also has a holder for a spare fuse
Power Cord Daisy Chain
Fuse Replacement
Trouble Shooting
Listed below are a few common problems the user may encounter, with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are wired correctly (pin
3 is “hot”; on some other DMX devices pin 2 may be ‘hot’). Also, check that
all cables are connected to the right connectors; it does matter which way the
inputs and outputs are connected.
Unit does not respond to sound:
1. Quiet or high pitched sounds will not activate the unit.
2. Make sure that Sound Active mode is activated.
Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical
lenses must be carried out periodically to optimize light output.
1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.
2. Clean the external optics with glass cleaner and a soft cloth every 20 days.
3. Always be sure to dry all parts completely before plugging the unit back in.
4. Cleaning frequency depends on the environment in which the xture operates
(i.e. smoke, fog residue, dust, dew).
Due to fog residue, smoke, and dust cleaning the internal and external optical
lenses must be carried out periodically to optimize light output.
1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.
2. Clean the external optics with glass cleaner and a soft cloth every 20 days.
3. Always be sure to dry all parts completely before plugging the unit back in.
4. Cleaning frequency depends on the environment in which the xture operates
(i.e. smoke, fog residue, dust, dew).

Rasha Professional A/S 375 W Esplanade Ave. San Jacinto, CA 92583 | 951-654-3585
rashaprofessional .com | [email protected] Rev. 101615
14
MANUFACTURER’S LIMITED WARRANTY
Rasha Professional A/S LLC. (Rasha Professional) hereby warrants, to the original purchaser,
Rasha products to be free of manufacturing defects in material and workmanship for a
prescribed period from the date of purchase (see specic warranty period on reverse). This
warranty shall be valid only if the product is purchased within the Continental United States
, including possessions and territories. It is the owner’s responsibility to establish the date
and place of purchase by acceptable evidence, at the time service is sought.
For warranty service you must obtain a Return Authorization number (RA#) before sending
back the product. Contact Rasha Professional Support Department at 951-654-3585.
Send the product only to the Rasha Professional A/S. factory. All shipping charges must
be pre-paid and insured for orgional purchase amount. If the requested repairs or service
(including parts replacement) are within the terms of this warranty, Rasha. will pay return
shipping charges only to a designated point within the the Continental United States. If
the entire xture is sent, it must be shipped in it’s original package. No accessories should
be shipped with the product. If any accessories are shipped with the product, Rasha
Professional A/S LLC. shall have no liability whatsoever for loss of or damage to any such
accessories, nor for the safe return thereof.
This warranty is void if the serial number has been altered or removed; if the product is
modied in any manner which Rasha Professional A/S LLC. Concludes, after inspection,
aects the reliability of the product; if the product has been repaired or serviced by anyone
other than the Rasha Professional A/S LLC. Factory unless prior written authorization was
issued to purchaser by Rasha Professional A/S LLC. if the product is damaged because
not properly maintained as set forth in the instruction manual.
This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specied above, Rasha Professional A/S LLC,.
will replace defective parts at its expense with new or refurbished parts, and will absorb
all expenses for warranty service and repair labor by reason of defects in material or
workmanship. The sole responsibility of Rasha Professional A/S LLC., under this warranty
shall be limited to the repair of the product, or replacement thereof, including parts, at the
sole discretion of Rasha Professional A/S Co., All products covered by this warranty were
manufactured after January 1, 2006, and bear identifying marks to that eect.
Rasha Professional A/S LLC.,. reserves the right to make changes in design and/or
improvements upon its products without any obligation to include these changes in any
products theretofore manufactured. No warranty, whether expressed or implied, is given
or made with respect to any accessory supplied with products described above. Except to
the extent prohibited by applicable law, all implied warranties made by Rasha Professional
A/S LLC.,. in connection with this product, including warranties of merchantability or
tness, are limited in duration to the warranty period set forth above. And no warranties,
whether expressed or implied, including warranties of merchantability or tness, shall
apply to this product after said period has expired. The consumer’s and/or Dealer’s sole
remedy shall be such repair or replacement as is expressly provided above; and under no
circumstances shall Rasha Professional A/S LLC.,. be liable for any loss or damage, direct
or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to Rasha Professional A/S LLC.,
Products and supersedes all prior warranties and written descriptions of warranty terms
and conditions heretofore published.

© Rasha Professional A/S LLC.
Ph: 961-654-3585
RashaProfessional.com
E-mail: [email protected]
Model: Hex V12 Wireless
Voltage: 100V ~ 240V/50~60Hz
LEDs: 9 x 18W High Brightness 6-in-1 – RGBWA+UV Color
Beam Angle: 25 Degrees
Working Position: Any safe working position
Power Draw: 150W (24Voltage)
Power Cord Daisy Chain: 33 Fixtures Max.
Fuse: 500mA
Weight: 3.3Kgs.
Dimensions: 20 (L) x6 (W) x 20 CM
Colors: RGB+Amber +White+UV Color Mixing and single color
Color: 16.7 million kinds of color change
DMX Channels: 7/12 DMX
Built In: 2.4 MHZ wireless Signal receiver
Control Mode: Stand alone/Maser selve/DMX/Auto
Warranty: 1Year (365 days)
Auto Sensing Voltage: This xture contains a automatic voltage switch, which will auto sense the
voltage when it is plugged into the power source.
Please Note: Specications and improvements in the design of this unit and this manual are subject to
change without any prior written notice.