Rauch Axent Isobus User manual

ISOBUS
INSTRUCTION MANUAL
AXENT ISOBUS
Please read carefully
before using the ma-
chine.
Keep for future reference.
This instruction manual/assembly in-
struction is to be considered as part of
the machine. Suppliers of new and sec-
ond-hand machines are required to
document in writing that the instruc-
tion manual/assembly instruction was
delivered with the machine and hand-
ed over to the customer.
Original instructions
5901646-d-en-0716

Preface
Dear Customer
By purchasing the AXENT ISOBUS machine control unit for the AXENT large area spreader,
you have shown confidence in our product. Thank you very much! We want to justify this confi-
dence. You have purchased a powerful and reliable machine control unit. If, contrary to expec-
tations, any problems occur: our customer service is always there for you.
Please read this operator's manual as well as the operator’s manual of the machine care-
fully before commissioning and follow the advice given.
This manual may also describe equipment that is not included in your machine control unit.
Please note that damage caused by incorrect operation or improper use may not be covered by
warranty claims.
Technical improvements
We are continuously improving our products. Therefore, we reserve the right to make any
improvements and changes to our machine that we consider necessary without notice.
This constitutes no obligation to make such improvements or changes on machines that
have already been sold.
We will be pleased to answer any other questions that you might have.
Yours sincerely
RAUCH
Landmaschinenfabrik GmbH
NOTE
Note the serial number of the machine control unit and of the machine
The AXENT ISOBUS machine control unit has been calibrated at the factory for the large area
spreader with which it was supplied. It cannot be connected to another machine without new cali-
bration.
Please enter the serial number of the machine control unit and of the machine here. When con-
necting the machine control unit to the machine, these numbers must be checked.
Serial number AXENT ISOBUS Serial number AXENT Year of construction
AXENT

Table of Contents
I
Preface
Technical improvements
1 User instructions 1
1.1 About this operator's manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Information on the illustration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2.1 Significance of warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2.2 Instructions and procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2.3 Listings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2.4 References. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2.5 Menu hierarchy, keys and navigation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Layout and function 5
2.1 Layout (CCI 100) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2 Control elements (CCI 100). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2.2 Touch screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2.3 Function keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2.4 Scroll wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2.5 Stop switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.3 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.3.1 Description of the operating screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.4 Library of symbols used. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.4.1 Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.4.2 Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.4.3 Operating screen symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.5 Structural menu overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3 Attachment and installation 17
3.1 Tractor requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.2 Connections, sockets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.2.1 ISOBUS terminal connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.2.2 Overview of actuators and sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Table of Contents
II
4 Operation AXENT ISOBUS 21
4.1 Activating the machine control unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.2 Navigation in the menus and between machine control units . . . . . . . . . . . . . . . . . 24
4.2.1 Navigation in the AXENT ISOBUS machine control unit . . . . . . . . . . . . . . . 24
4.2.2 Switching between machine control units. . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.3 Interaction between both machine control units . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.4 Main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.5 Hopper cover (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.6 AXENT ISOBUS functional description: Status indicator . . . . . . . . . . . . . . . . . . . . . 31
4.6.1 Spreading material supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.6.2 AXENT hopper empty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4.7 Machine settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.7.1 Operating mode of fertiliser supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.7.2 Lime operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.7.3 Belt speed (mm/s). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.7.4 +/- belt speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.7.5 Opening the pre-metering slides (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.7.6 Opening adjustment (%) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.7.7 Forward speed calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4.8 Fast emptying. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.9 System/test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.9.1 Test/diagnosis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.9.2 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
4.10 Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
4.11 Weighing/Trip counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
4.11.1 Trip counter (only lime operation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
4.11.2 Residual quantity (only large area spreader with weighing function) . . . . . . 51
4.11.3 Zero scales (only large area spreader with weighing function). . . . . . . . . . . 52
4.12 Special functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
4.12.1 Text input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
4.12.2 Selection window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4.12.3 Setting the system of units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Table of Contents
III
5 Loading with AXENT ISOBUS machine control unit 57
5.1 Loading in automatic operating mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
5.2 Loading in manual operating mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
5.3 Loading in lime operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
6 Alarm messages and possible causes 63
6.1 Meaning of the alarm messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
6.2 Clearing an error/alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
6.2.1 Acknowledging an alarm message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Index A
Terms/conditions of warranty

Table of Contents
IV

User instructions
1
1
1 User instructions
1.1 About this operator's manual
This operator's manual is an Integral part of the AXENT ISOBUS machine con-
trol unit.
The operator's manual contains important instructions for the safe, proper and
economic use and maintenance of the machine control unit. Compliance with
its stipulations helps to avoid risks, reduce maintenance costs and downtime
and to increase the machine's reliability and service life.
The operator's manual is an integral part of the machine. The complete documen-
tation must be kept in an easily accessible location close to where the machine
control unit is used (e.g. g. in the tractor).
The operator's manual does not replace your own responsibility as the operator
and operating personnel of the machine control unit AXENT ISOBUS.
1.2 Information on the illustration
1.2.1 Significance of warnings
The warning instructions in this manual have been structured according to the de-
gree of danger and the probability of their occurrence.
Danger signs and symbols inform the user about other construction-related and
unavoidable residual risks that may be encountered when operating the machine.
The warning notes used are structured as follows:
Example
Signal word
Symbol Explanation
n DANGER
Risk to life if warning is not observed
Description of the danger and possible consequences.
Ignoring these warnings will result in very serious or even fatal
injury.
Measures to prevent the danger.

User instructions1
2
Warning severity level
The degree of danger is indicated by the signal word. The levels are classified as
follows:
n DANGER
Type and source of danger
This warning warns of a danger posing an immediate threat to the
health and life of persons.
Ignoring these warnings will result in very serious or even fatal
injury.
Always observe the measures described to prevent this
danger.
n WARNING
Type and source of danger
This warning warns of a possible dangerous situation for the
health of persons.
Ignoring these warnings will result in very serious injury.
Always observe the measures described to prevent this
danger.
n CAUTION
Type and source of danger
This warning warns of a potentially dangerous situation for per-
sonal health or of material and environmental damage.
Ignoring this warning can result in injuries and damage to the
product or the general area.
Always observe the measures described to prevent this
danger.
NOTICE
General information containing application tips and particularly useful informa-
tion, but which constitutes neither warnings nor hazards.

User instructions
3
1
1.2.2 Instructions and procedures
Steps that the operator must carry out are shown as a numbered list.
1. Instruction for action step 1
2. Instruction for action step 2
Instructions involving only one step are not numbered. The same applies for ac-
tion steps that do not have a specific sequence.
A bullet is placed in front of these instructions:
Handling instruction
1.2.3 Listings
Listings without a specific sequence are shown with bullet points (level 1) and
dashes (level 2):
Property A
- PointA
- PointB
Property B
1.2.4 References
References to other text passages in the document are indicated with section
number, headline text and page number:
Example: See also chapter 3: Safety, page 5.
References to other documents are indicated as note or instruction without exact
chapter or page number:
Example: Please also observe the instructions contained in the manual for
the universal drive shaft.
1.2.5 Menu hierarchy, keys and navigation
Menus are the entries listed in the Main menu window.
In the menus, submenus and/or menu items are listed in which settings can be
implemented (selection lists, text or number entries, starting a function).
The various menus and buttons of the machine control unit are illustrated in bold
letters:
The hierarchy and the path to the requested menu item are marked with an
>(arrow) between menu, menu item/s:
System / test > Test/diagnosis > Voltage means that you can access the
Voltage menu item via the System / test menu and the Test/diagnosis
menu item.
- The arrow >corresponds to the operation of the scroll wheel and/or the
button at the screen (touch screen).

User instructions1
4

Layout and function
5
2
2 Layout and function
2.1 Layout (CCI 100)
Figure 2.1: Terminal CCI 100 overview
NOTICE
Due to the great variety of different ISOBUS-compatible terminals, the present
chapter is restricted to the layout and functions of the CCI 100 ISOBUS terminal
as an example.
Please observe the instructions in the respective operator's manual of your
ISOBUS terminal.
No. Designation Function
1 Control panel Including foil keys, display, scroll wheel and stop
switch.
2 USB port with cov-
er
Protects the USB port from dirt. For data exchange,
task controller and terminal updates.
3 Mounting bracket For mounting the terminal within the tractor cabin.
4 Terminal strip Terminal strip for the cables of the ISOBUS system.
5 Softkey switch Enables switching the functions from the left to the
right side of the screen.
12
3
4
5

Layout and function2
6
2.2 Control elements (CCI 100)
2.2.1 Overview
The CCI 100 machine control unit is operated with the following control elements:
18 foil buttons (6 firmly defined, 12 freely assignable foil buttons).
Scroll wheel
Stop switch
Softkey switch
Figure 2.2: Operating panel on the front side of the unit
NOTICE
For further information on operating the CCI 100 terminal and its control ele-
ments, refer to the enclosed operating manual. The operating manual is an in-
tegral part of the terminal unit.
!
1
2
3
4
5
6
7
8109
2

Layout and function
7
2
2.2.2 Touch screen
The CCI 100 terminal is equipped with a touch screen. The buttons on the screen
(OK, symbols in the working screen, etc.) can be pressed and menu entries can
be opened directly.
No. Designation Function
1 Scroll wheel Navigation through the menus and input fields and
to acknowledge entries.
2 Function keys
F1 - F12
12 keys with variable functionalities, depending on
the menu screen.
Page 8
3ACK key Acknowledgement of error messages.
4Information key Freely assignable key. Refer to the CCI 100 termi-
nal operating manual.
5Double arrow key Navigation between the system screens of the ter-
minal.
6Main menu key Changing to the main menu of the terminal (refer to
the manufacturer operating manual).
7 ON/OFF Switching the terminal on/off.
8 Stop switch The stop switch puts the connected devices into a
safe state. Not all ISOBUS terminals support the
stop switch.
Page 9
9 Touch screen Direct activation of the button
Input of values
10 ESC key Cancelling inputs.
NOTICE
Please observe the operating manual of the CCI 100 terminal. The operating
manual is an integral part of the terminal/machine.

Layout and function2
8
2.2.3 Function keys
Depending on the type of terminal, it can be equipped with 1x6 (minimum require-
ment), 2x5 or 2x6 function keys. On the left and right-hand side, next to the
screen of the CCI 100 ISOBUS terminal, two groups of 6 function keys each are
allocated in a vertical position.
The assignment of the function keys depends on the displayed menu screens.
Functions are generally executed by pressing the function key next to the icon or
by pressing the button on the touch screen.
Function keys without icon do not have any functionality in the respective menu
screens.
2.2.4 Scroll wheel
The scroll wheel is used for fast navigation in the menus as well as for entering
or changing data in input fields.
Turning the scroll wheel enables navigation between the selectable fields.
Pressing the scroll wheel to confirm the selection.
Figure 2.3: Scroll wheel at the CCI 100

Layout and function
9
2
2.2.5 Stop switch
By pressing the stop switch, all connected devices are set to a safe condition.
For unlocking the stop switch, turn it in the direction of the arrow until the
switch pops out again.
The stop switch is unlocked.
Figure 2.4: Stop switch at the CCI 100
Case 1 - Spreading operation
Pressing the stop switch during spreading operation:
- the pre-metering slides are stopped.
- the conveyor belt is stopped.
- the comb roller is stopped.
- the hopper cover is stopped.
Case 2 - No spreading operation (example: calibration/fast emptying)
If no spreading operation is active, all functions are stopped and the metering
slides remain open.
A warning message is displayed as soon as the stop switch is actuated.
1. Rectify the cause of the fault.
2. Unlock the stop switch
Another alarm message warning against possible unexpected move-
ments is displayed.
3. Press the ACK foil key
n CAUTION
Risk of injury from rotating spreading discs!
The spreading discs are not stopped.
Switch off the PTO shaft of the tractor.
Ensure that nobody is in the hazard zone.
!

Layout and function2
10
2.3 Display
The display shows the current status information as well as the selection and in-
put options for the machine control unit.
The most important information on the operation of the mineral fertiliser spreader
is displayed on the operating screen.
2.3.1 Description of the operating screen
NOTICE
The exact representation of the operating screen depends on the actual settings
selected.
Figure 2.5: Machine control unit display
1
910 8
13
14
11
12
15
3
4
5
6
2
77
[1] Left pre-metering slide display
[2] Large area spreader filling level display
[3] Right application rate adjustment
[4] Current opening position of right pre-meter-
ing slide
[5] Right pre-metering slide display
[6] Right spreading unit filling level display
[7] Function keys
[8] Display field: Conveyor belt speed
[9] Display field: Forward speed
[10] Display field: Residual quantity in AXENT
hopper
[11] Left spreading unit filling level display
[12] Conveyor belt display
[13] Current opening position of left pre-metering
slide
[14] Left application rate adjustment
[15] Selected operating mode

Layout and function
11
2
2.4 Library of symbols used
The AXENT ISOBUS machine control unit displays symbols for the individual
menus and functions.
2.4.1 Navigation
Symbol Meaning
Go to the left; previous page
Go to the right; next page
Back to the previous menu
Back to main menu
Switching between working screen and menu window
Cancellation, closing the dialogue window

Layout and function2
12
2.4.2 Menus
Symbol Meaning
Change from a menu window directly to the main menu.
Switching between working screen and menu window
Hopper cover
Machine settings
Fast emptying
System/test
Information
Weighing/Trip counter

Layout and function
13
2
2.4.3 Operating screen symbols
Symbol Meaning
Automatic operating mode
Manual operating mode
Speed-dependent lime spreading operating mode
Warning symbol: The rear cover is open
Start loading
Start lime spreading
Stop lime spreading
The pre-metering slide can be closed.
The "keep pre-metering slide open" function is active.
Selection of the open position for pre-metering slide (%)
Increase + (plus) pre-metering slide opening
Decrease – (minus) pre-metering slide opening
Increase (plus) conveyor belt speed;
Terminals with 2x6 function keys only

Layout and function2
14
Decrease (minus) conveyor belt speed;
Terminals with 2x6 function keys only
Switching between working screen and menu window
Pre-metering slide open position reset to preset opening value.
Symbol Meaning