Raymor Edge ii 203147 User manual

bend (136002) has a set out of 150 to 165mm and is available for purchase separately. DO NOT BED THE PAN IN PLACE USING

Installation Instructions

203147 / 203148 Edge II Rimless Wall Faced Toilet Suite w/ Slim or STD Seat

Important Information

This Product is to be installed by a licensed plumber, installation must comply with AS/NZS 3500 and relevant plumbing codes.

Isolating stop taps are recommended to be fitted to the hot and cold inlet connections. Please leave this document with the Product

after installation. Please ensure that the lines are flushed prior to installation as contaminates in the water can damage O-rings and

valves and will affect the performance of the Product.

Before installation, remove Product from packaging and check the Product matches what you have ordered, is complete with all parts

(per exploded drawing) and is not damaged. If the Product is incorrect, damaged or missing parts DO NOT install and return to store

with proof of purchase for a refund or replacement. Installed Products are warranted for genuine manufacturing defects arising in your

Product during the course of normal domestic or equivalent commercial use for the term of the warranty period. Our manufacturer's

warranty does not cover Product which are incorrect or have been installed with pre-existing damage or missing parts.

Pressure & Temperatures

- Maximum Hydrostatic Pressure - 500kPa. (per AS/NZS3500.1 (Clause 3.3.4) which states "The maximum static pressure at any outlet,

other than a fire service outlet, within a building shall not exceed 500kPa." NB. Pressures above 500kPa can cause damage from water

hammer, reduced life of appliances, taps and fittings, and cause excessive noise in the system.

- Minimum Hydrostatic Pressure - 100kPa. This Product may not be suitable for use with a gravity fed water supply or with continuous

flow or instantaneous hot water systems.

- Maximum operating temperature - 65°c.

Revision Date: 25 Nov 2021

Revision Number: 1.0

Issue Date: 25 Nov 2021

Optional Set Out

Set Out Drawing

Installation Instructions - Page 1

1. Pan Installation - mark the centre line of the pan connector on the floor for 'S' trap installation or on the wall for 'P' trap installation.

2. Place the pan into position, centralising the pan with your centre line, then draw around the pan base and mark the entry points on

the floor to where the floor fixing holes are located on the side of the pan.

3. Remove the pan and drill and screw the floor fixing brackets into place. Set the floor fixing brackets 20mm inside the line drawn

around the base of the pan. Use suitable floor fixing screws / anchors to suit the floor material. NB. The pan must be on a level surface

that is square with the wall. If the floor slopes away, the pan will need to be levelled using suitable floor chocks around the pan which

will support and stabilise the pan. The standard variance bend (133601) supplied has a set out of 90 to 105mm. The optional variance

CEMENT, CONCRETE OR SIMILAR MATERIAL.

4a. 'S' trap installation - place the variance bend into the floor outlet, from the floor to the centre of the pan outlet is 185mm, ensure the

variance bend is straight and square to the wall, assemble the variance bend wall brace and fix to the finished wall. Measure the

distance from the back edge of the pan to the start of the 'P' trap and add on sufficient length for the variance bend collar to fully

engage the 'P' trap. Remove the locking ring and rubber boot from the variance bend. Measure out from the finished wall to the

measurement you have predetermined and cut the excess off the variance bend. The distance between each ridge on the variance

bend is 10mm. Once the excess has been cut off the variance bend reas semble the rubber boot and locking ring. Use the supplied

variance bend wall bracket, with appropriate screws or anchors for the wall material, to fix the variance bend to the wall and to reduce

the risk of misalignment.

5. Slide the pan into place, being careful that full engagement of the pan 'P' trap and variance bend has been achieved .

NB. pre-soaping the rubber boot on the variance bend will assist with easier engagement onto the pan 'P' trap.

6. Once the pan is in place and connected to the variance bend, screw the pan in place using the supplied fixing screws and cover. DO

NOT OVER TIGHTEN SCREWS AS THIS MAY CAUSE THE PAN TO CRACK . Run a bead of plumbing grade silicone around the pan and

up the edge of the wall to finish off.

7. 'P' trap installation - The distance from the back edge of the pan to the start of the 'P' trap is 130mm (due to shrinkage variations

please measure the distance on the pan to confirm} taking into account full engagement of the pan collar on the 'P' trap. Install waste

pipe as per Australian standards and local authority requirements. The distance from the floor to the centre of the 'P' trap is 185mm, set

your waste pipe height accordingly. DO NOT USE OFFSET PAN COLLARS ON 'S' OR 'P' TRAP INSTALLATIONS AS THIS WILL

COMPROMISE WASTE DISCHARGE.

Contact Details

Tradelink Pty Ltd

ABN:29000003832

Raymor Customer Care

Ph: 1800 729 667

1051 Nudgee Road Banyo QLD 4014

[email protected]

NB. These installation instructions are to be used in conjunction with the Byron Inwall Cistern installation instructions.

1800 729 667

[email protected]

Warranty Provider

Tradelink Pty Limited ABN 29 000 003 832 of 1051 Nudgee Rd Banyo QLD 4014 (Tradelink) offers warranties on each of the products set out in Schedule A (Product(s)) for the warranty

periods specified, the details of which are set out in this document (Raymor Warranty). This Raymor Warranty is effective as of 1st January 2022 and supersedes and replaces any previous

version of this document.

Raymor Warranty

This Raymor Warranty only covers the Products set out in Schedule A and does not extend to items that you have selected outside this range, including the items set out in Schedule B.

Your Raymor Warranty commences from the date of purchase of your Product (or, for new buildings, on the date of handover) for the relevant period set out in Schedule A and is valid for

purchases of Products made on or after the 1st March 2014. Your Raymor Warranty does not extend to the items set out in Schedule B and these items are sold with the warranty provided by

the manufacturer, in addition to any rights and remedies you may have under the Australian Consumer Law. Please refer to the warranty document (if any) provided by the manufacturer

named in Schedule B or contact the manufacturer for details.

The Raymor Warranty only applies to you if you are the original purchaser of the Product. It is not transferable.

What We Will Do

Subject to the terms and exclusions contained in this Raymor Warranty document, where a genuine manufacturing defect arises in your Product during the course of normal Domestic Use or

Equivalent Commercial Use within the warranty period set out in Schedule A, Tradelink will, at its election repair the defect (without cost to you for labour or replacement parts) or replace the

Product.

Limitation of liability under Raymor Warranty

To the fullest extent permitted by law and subject to and without limiting your consumer rights under the Australian Consumer Law, Tradelink expressly limits its liability under this Raymor

Warranty and under any other statutory guarantee imposed at law to, at its option:

−the replacement or repair of the Product;

−the supply of an equivalent Product; or

−the payment of the cost of the Product or of repairing the Product or of acquiring an equivalent Product.

−In the event the Product is unavailable or unable to be supplied and a replacement is required, Tradelink reserves the right to supply a Product of equal quality, value and type at

their discretion.

To the fullest extent permitted by law, Tradelink expressly excludes:

−all liability for damage or injury to any person;

−damage to any Property;

−loss of profit, loss of revenue, loss of use, loss of business, loss of opportunity, loss of goodwill, loss of contracts, loss of production, business interruption or any kind of indirect,

special or consequential loss or damage arising in connection with the defective product;

−all conditions, warranties and undertakings in relation to the Products except as set out in this document.

Australian Consumer Law

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any

other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a

major failure. This Raymor Warranty is in addition to your rights and remedies under the Australian Consumer Law.

SCHEDULE A: WARRANTY – PRODUCTS AND WARRANTY PERIODS

Raymor Product^ sold after 1st March 2014 (Exclusions Apply)

Category

Range

Manufacturer warranty provider

Vanities

Salt, Wentworth

Architectural Designer Products Pty Ltd

Eco, Hampton

Marquis Bathroom Products Pty Ltd

Outline, Ease, Stasis, Ocean

Showerama Products Pty Ltd

Water Filters

Filtration Systems

Puretec Pty Ltd

Cartridges

Puretec Pty Ltd

Brass Cartridge Mixers

Banjo BC

Ramtaps Pty Ltd

Mixers

Alor, Lavas

Phoenix Industries Pty Ltd T/A Phoenix Tapware

Baths & Spa Baths

Aruba, Jamaica, Recline

Decina Bathroomware Pty Ltd

Shower Systems

Trinidad screens, walls

Decina Bathroomware Pty Ltd

Trinidad, Luna shower bases

Decina Bathroomware Pty Ltd

How to make a warranty claim

To make a warranty claim, please contact Tradelink using the contact information contained in this Raymor Warranty document. No specific claim form is required however the following

documentation must be supplied to Tradelink as part of your claim:

−Proof of purchase or handover documentation (for new homes);

−Your contact details, including the address of the installed Product; and

−A photo of your Product and the defect in question.

If the Product has not been installed, the Product can be returned with proof of purchase to the place of purchase. The cost of returning the Product is your responsibility; however, if the cost

of returning any defective Product is unreasonable, please contact Tradelink on the telephone number listed below so that, if appropriate, we can arrange a collection. You must bear your

own costs incurred in making a warranty claim.

Tradelink requires reasonable and adequate access to Products, fittings and fixtures to undertake warranty repairs during normal weekday working hours. To the fullest extent permitted by

law and subject to and without limiting your consumer rights under the Australian Consumer Law, Tradelink will not be responsible for any loss, damage or costs where reasonable and

adequate access to Products, fittings and/or fixtures is not provided. Where parts or products are replaced or supplied under this warranty, the replacement parts or product shall be

considered to be warranted from the original Product date of purchase.

If a Raymor Warranty service call finds that your Product does not have a genuine manufacturing defect, Tradelink reserves the right to charge you a service fee.

Tradelink reserves the right to provide you with minor components as ‘parts only’.

Contact Information

Warranty contact information for Tradelink is as follows:

Raymor Customer Care

Phone: 1800 RAYMOR (1800 729 667)

Email: customercare@raymor.com.au

1051 Nudgee Rd, BANYO QLD 4014

What is not covered

Your Raymor Warranty does not cover any defect or damage caused or partly caused, by or arising through: fair wear and tear (e.g. working seals in the inlet and outlet valves, scratching

from cleaning, etc.); misuse, incorrect storage or handling of the Products; failure to correctly install, use or maintain the Product or to follow any instructions or guidelines for installation, use

or maintenance of the Product; adverse environmental conditions; faulty design of a system in which the Products are used; the use of the Product otherwise than for any application

specified on a quote or order form, price book or catalogue issued by Tradelink; the continued use of the Product after any defect becomes apparent or would have become apparent to a

reasonably prudent operator or user; or any accident or act of God.

Your Raymor Warranty will be voided if any of the events detailed below arise:

−You are unable to provide proof of purchase or equivalent documentation from an authorised retailer of a Product;

−If the Product is not installed by a licensed plumber and/or electrician;

−If the Product is not installed in accordance with relevant Australian Standards, NCC and state regulations;

−If the Product is not installed in accordance with the manufacturer’s installation instructions;

−If the water pressure exceeds stated limitations as per the Product installation instructions;

−If the hot water system delivery temperature at the outlet exceeds 65 degrees Celsius;

−If isolation stop taps are not fitted per AS/NZS 35--.5:2000 requirements for appliances and apparatus or the manufacturer's installation instructions;

−Failure to reasonably check and adjust fittings and connections during installation (e.g. pull-out mixer hose operation and weight position, adjust toilet flush rods and tighten

cistern fittings, ensure plumbing connections are deburred and level, ensure vanity cabinet is square and level, etc.);

−If other devices are fitted to the outlet of tapware (e.g. water filters or stop valves);

−Tradelink non-approved parts are fitted in tap body or end of line water flow regulating devices;

−If repair, service, alteration or replacement has been undertaken without the prior approval of Tradelink

−If works are undertaken by a non-approved service agent or technician or where works are undertaken with non-standard or non-genuine replacement parts;

−If inappropriate or non-approved connection fittings are used connecting Product to sewer;

−If unauthorised modifications are made to Product;

−If the Product is used for an incorrect application such as non-potable water, in commercial kitchens, restaurants, cafes, manufacturing facilities, etc.;

−If the defect is a result of obstruction or damage due to inadequate flushing of system or problems caused by water supply (e.g. silt, thread tape, silicone, metal shavings,

corrosion and excessive water pressure over 500kpa);

−If particulates of ferrous or corrosive elements on the sink react chemically and cause rust and/or pitting into the stainless. Stainless steel does not rust under typical indoor

atmospheric and temperature conditions.;

−If there is a failure to regularly clean or replace dirty or blocked tapware aerator inserts and/or shower heads, etc.;

−If there is a failure to regularly inspect flexible hoses for signs of failure including bulging, rust, wear, moisture, breaks, kinking, staining or discolouration;

−The removal or failure to install flow regulator in tapware or showers or regulated check valve or check valves in hand showers or veggie mixers;

−If the Product is used with water additives (i.e. cleaning chemicals, disinfectants or additives in toilet cisterns); damage is caused to any surface, finish or protective coating by

adhesives, sealants, etc.;

−If damage is caused to any surface, finish or coating by an abrasive or harsh product (e.g. solvent, disinfectant, dye, bleach, oil, polish, acid, degreaser, alcohol, aerosol, etc.);

−Exposure to ferrous metals or oxidants on stainless steel or chrome surfaces occurs (including exposure to cast iron, steel wool, bleach, hard water, etc.);

−If installation or removal costs are incurred after installation of Products which contained obvious or visible faults;

−If damage caused to the Product from installation or post installation use, abuse or misuse;

−If surfaces between paired product are not adequately sealed during installation or commissioning (e.g. between a basin and waste, mixer and sink/basin, mixer body and finished

wall, etc.);

−Product damage is caused by misuse or abuse, as determined by a Tradelink Authorised Service Agent; or

−Where a Product is coupled or used with a product other than a Product, the Raymor Warranty is limited only to the Product.

It is the responsibility of you and/or the installer to ensure that prior to installation:

−the Product is not damaged;

−you are happy with your purchase; and

−the Product has all its components.

If the Product is damaged, incorrect or missing parts do not install and return to store. Following installation of your Product, it is your responsibility to ensure all required maintenance is

performed. Installed Products are warranted for genuine manufacturing defects arising in your Product during the course of normal domestic or equivalent commercial use for the term of the

warranty period. Our manufacturer's warranty does not cover Product which are incorrect or have been installed with pre-existing damage or missing parts.

Care Information

To ensure that you receive the longest lasting product life possible, we offer the following general advice to you for the care and maintenance of your Products:

−Regularly clean with warm, soapy water or detergent. Do not use caustic, corrosive or abrasive chemicals.

−Use a soft, dampened sponge or cloth. Never use an abrasive brush, pad, cloth or scourer to clean your Products.

−Chrome and stainless steel finishes should never be cleaned with chlorides, steel wool, wire brushes,

−Wipe surfaces clean and thoroughly rinse with water immediately after using any cleaner or solution.

Plastic, stainless steel, chrome, brass, vitreous china, silicone and polymarble Products are generally considered to be stain-resistant and durable but care should be taken in their use and

maintenance as they are not stain-proof or scratch-proof. Vanity cabinets are manufactured from moisture-resistant materials but are not water-proof and care should be taken to wipe up

spills and drips immediately and use in a well-ventilated environment.

Definitions and Interpretation

In these terms and conditions of warranty: “You” means the purchaser or customer acquiring the Goods and “Your” means belonging to you. “We” and “Us” means Tradelink as the

manufacturer of the Goods and “Our” means belonging to Us. “Goods” means the goods You claim to be defective.

“Equivalent Commercial Use” is defined as all equivalent to normal domestic use for other than normal residential domestic purposes. Equivalent Commercial Use includes the use of

Products in non-business or non-commercial settings (such as public buildings, educational settings, not-for-profit organisations, sports centre communal spaces, lunch rooms, hotel rooms,

home offices or in-home business settings). Equivalent Commercial Use excludes the use of Products in commercial kitchens, restaurants, cafes, commercial food preparation spaces and

manufacturing facilities, etc.

This manual suits for next models

Other Raymor Toilet manuals