RCA RPJM030 User manual

尺寸：A3纸
材质：80克书纸黑白印刷

Technical Data：
Suitable for different kinds of projector
VESA standard: Unlimited
The tle angle can be freely adjusted
The complete set of installaon
screws are included
Maximum loading: 18KGS
Material: SPCC
Color: Black.
Product Height: 135mm
* Note: the projector you are installing may differ in appearance from the sample illustrated below.
Place projector upside down. Locate Product Assembly (A) with Universal Plate facing forward as
close to projector center of gravity as possible without covering any mounng holes Loosen
Extension Bracket, and if there are only three mounng holes remove fourth Extension Bracket.
Using one Extension Bracket for each mounng hole posion Extension Bracket,boom washer
(D) and washers (E, G) over mounng holes as shown in fig 1
Important: if projector dose not have at least three mounng holes, do not use this adapter plate
*Note: Some projectors have feet, which can be removed, and the corresponding threaded insert
can be used for a mounng hole.
*Note: Once Extension Bracket are in posion reghten fasteners.
*Aach Product Assembly (A) to projector using one screw (B,C) for each channel as shown in fig2.
Tighten all screws, while keeping the center of gravity. Be sure that Prodect Assembly (A) is
straight. Tighten all screws with Phillips screwdriver, while keeping the center of gravity.
*Note: Projectors will require different size screws for mounng. Use a suitable screws (B,C) and
Washers (E, F, G) that will result in Extension Bracket of Product Assembly (AA) fing ghtly
against projector. Important : In order to properly engage the threads in the mounng holes,
the screw must be turned at least 3full turns. Cauon: it is the responsibility of the installer to
ensure that the projector is properly verlated.
Item Description Qty.
Parts List
A
B
C
D
E
F
G
H
I
J
K
Product Assembly
Truss Head Screw M4x25
Button Head Cap Screw
Truss Head Screw M6x25
Bottom washer
1mm washer
2mm washer
3mm washer
Square Nut
Tighten tool
Tighten tool
Extens on Bracket 1
Extens on Bracket 2
1
4
4
3
4
4
4
4
1
1
2
Fig 1
Fig 2
Installation tools (not included)
Electric drill 8mm-dril
Hammer Screwdriver
-20°
/
+20°
60°
MODEL NO. RPJM030
UNIVERSAL PROJECTOR CEILING AND TABLE MOUNT
INSTRUTION MANUAL
PLEASE READ BEFORE OPERATING THIS EQUIPMENT
This product is manufactured and sold by Curtis International Ltd.
RCA, the RCA logo, the two dogs (Nipper and Chipper) logo, are registered
trademarks or trademarks of RCA TrademarkManagement and are used
under license by Curtis International Ltd. Any other product, service,
company, trade or product name and logo referenced herein are neither
endorsed nor sponsored by RCA Trademark Management or its affiliates.
For service assistance and product information, please call: 1-800-968-9853.
Curtis International Ltd.
7045 BECKETT DRIVE, UNIT 15,
MISSISSAUGA, ON, L5S 2A3 www.curtisint.com
A1
4
1
L
L2
IJ
B
A

View of product
Noce: 1 The installer must ensure that the ceiling can safely supports four mes the weight of all addional equipments.
2 This ceiling mount is available to adjust the angle between +-30º 。
INSTALLATION OF TABLE MOUNT
Aach the 240P or 480P small projector to the mounng bracket , and ghten the screw securely to hold the projector in posion
INSTALLATION OF CEILING MOUNT
1. Take out the projector that you want to install, put it on table
upside down. Place "A1" part at the middle of the boom of
the projector.
3. Place the gasket G under the screw hole of the extension
metal bracket .
5. Adjust the middle bracket of A1 to be parallel to the unit front
face, and then ghten the four screws by "I" tool.
Note: If installing the ONA19AV901 projector on this ceiling
mount, please remove the four screws on the boom firstly.
2. According to you product side to select extension
metal bracket K or L .
Note: the ONA19AV901 projector need to use the long
metal bracket K.
6. Finally ghten the mount to the Ceiling .
4. According to your product, choose different thickness
gasket (D, E, F for opon) , place the gasket on the
screw hole of the extension metal bracket, and then
select the correct screw as per the product screw hole
size ( A,C for opon). Then ghten the screw.
L
1