RCA RCU403R User manual

2
+
ON•OFF
CODE
SEARCH
CHAN
PREV CH
VOL
MUTE
12 3
654
78 9
0
ENTER INPUT
FFPLAYREW
REC PAUSE STOP
SLEEP MENU
SAT • CBL• DTC VCR•DVD TV
-
( )
Indicator ight
Component keys.
(TV,VCR•DVD,
SAT•CBL•DTC)
CHAN and VOL
keys have dua
functions. They act
as navigation keys
(up, down, eft,
and right) in
menu systems.
Dedicated MENU
key for DVD
disc menus, some
TVs and sate ite
receivers.
Table of Contents
ProductDiagram ....................................2
Introduction.........................................3
Battery Installation and Information . . . . . . . . . . . . . . . . . . . .3
eyDescriptions.....................................3
Program for TV—Direct Entry Method . . . . . . . . . . . . . . . . .5
Program for DVD or VCR—Direct Entry Method . . . . . . . .6
Program for Satellite, Cable Box or Digital TV Converter —
DirectEntryMethod ..................................7
CodeSearchMethods ................................8
ManualCodeSearch ..............................8
AutomaticCodeSearch ...........................8
CodeRetrieval.......................................9
SleepFeature .......................................10
On-screenMenus ...................................10
Accessing a Menu System . . . . . . . . . . . . . . . . . . . . . . . .11
Highlighting and Selecting Menu Items . . . . . . . . . . . .11
ExitingaMenuSystem ...........................11
Troubleshooting ....................................12
Limited90-DayWarranty ............................14
Actua mode may vary from picture shown
INPUT(-) key has
severa functions,
inc uding accessing
digita channe s
direct y ( ike 59.1)

3
Battery Installat on
and Informat on
Your universal remote requires two AAA Alkaline batteries
(batteries may or may not be included, depending on model).
To install the batteries:
1. Remove the battery compartment cover.
2. Insert the batteries, matching the
batteries to the (+) and (–) marks
inside the battery compartment.
3. Press and push the battery cover
back into place.
Congratulations on your purchase of the 3-component
universal remote. This universal remote controls up to three
electronic components and makes juggling remote controls a
thing of the past. You can program this RCA-brand universal
remote to operate most models of most brands of infrared,
remote-controlled components manufactured after 1990. (See
the enclosed Code List for a complete list of brands.) The 3-
component universal remote is easy to use, easy to program
and gives you control at the touch of your fingertips.
Note: The 3-component universal remote is already
programmed to operate most RCA, GE and PROSCAN
branded TVs, VCRs, DVD players and satellite receivers. Just
press the corresponding component key—VCR•DVD for
a VCR or DVD player; TV for a television; SAT•CBL•DTC for
a satellite receiver, cable box or digital TV converter.
3-Component Univer al Remote
+
ON•OFF
CODE
SEARCH
CHAN
PREV CH
VOL
MUTE
12 3
654
78 9
0
ENTER INPUT
FFPLAYREW
REC PAUSE STOP
SLEEP MENU
SAT • CBL• DTC VCR•DVD TV
-
( )
Key Descr pt ons
Indicator Light–flashes when a valid key
is pressed to indicate the remote is working.
Status of this light is important when you
are programming the remote.
Component keys (SAT•CBL•DTC,
VCR•DVD,TV): selects the component
you want the remote to operate.
For example, after you’ve programmed the
remote to operate your TV, you must press
the TV key first to put the remote in TV
Mode. While in TV Mode, the CHAN keys
change the channel on the TV, the VOL keys
adjust the TV’s volume, etc.
Transport keys–REW (Rewind), PLAY,FF
(Fast Forward), PAUSE,STOP: operate
the same as your original VCR or DVD
remote control, although key labels may
vary (REVERSE,FORWARD).

4
Other Keys (listed alphabetically)
0-9 (Number eys):operate the same as number keys on your
original remote and are used to enter component codes when
programming the remote control with Direct Entry method.
INPUT(-): in TV mode, switches between the signal coming
from a satellite receiver or cable box and an off-air antenna
or digital TV converter. In VCR mode, switches between the
signal coming from a VCR and a TV. When accessing digital
TV channels directly, this key lets you separate the main
channel number from the sub-channel number (such as
“59.1”)
CHAN (Channel) UP AND DOWN: goes to the next highest
or lowest channel number in the component channel list,
respectively, except for DVDs. In DVDs the CHAN UP/DOWN
goes to the NEXT/PREVIOUS chapter. Additionally, when
you’re using the remote with On-screen Menus, the CHAN
keys act as UP ARROW and DOWN ARROW keys (moving
the cursor or highlight up or down).
CODE SEARCH: use to program the remote.
ENTER: use with Manual or Automatic Code Search method
to accept code (See Code Search on page 8). Also, some
brands require you to press the ENTER key after you enter
a channel number. In some menu systems, you must press
ENTER to select a highlighted item.
MENU: accesses DVD disc menus when VCR•DVD key
is programmed to operate a DVD player. Accesses menu
systems of some TVs, a few RCA brand VCRs and satellite
receivers. (For more information, refer to Using On-screen
Menus section on page 10).
MUTE: lowers the TV’s volume to its minimum level.
ON•OFF: turns component on and off.
Note: Some RCA, GE and PROSCAN models require that
you press the component key to turn ON the component
and the ON•OFF key to turn OFF the component.
PREV CH (Previous Channel):switches back to previous
channel—operates the same as LAST CHANNEL,GO BACK
or RECALL key found on some brands of remote controls.
REC (Record):used with VCR to record programming.
You must press the REC key twice to start recording.
VOL (Volume) UP and DOWN:increases or decreases the

5
(OFF)
ON•OFF
TV CODE
Program for TV—
D rect Entry Method
1. Manually turn on the TV.
2. Locate the enclosed TV Code List.
Find your brand of TV.
Note: If your brand isn’t listed, use
one of the Code Search methods to
program this remote control (See
Code Search on page 8).
3. Press and hold the CODE SEARCH
key until the indicator light
illuminates. Then release the
CODE SEARCH key.
4. Press and release the TV key. The
indicator light blinks and then remains lit.
5. Use the number keys to enter
the first code listed for your brand.
After you enter a valid four-digit
code, the indicator light turns off.
Note: If you enter an invalid code,
the LED will flash rapidly for 2
seconds. Start over at step 3.
6. Aim the remote at your TV and press
the ON•OFF key. If your TV turns
off, you have found the correct code.
7. Enter the code in the box provided
on this page for future reference.
8. If your TV doesn’t turn off, repeat
steps 3-6 above, entering the next
code for your brand.
If none of the codes work or your
brand is not listed, use one of the
Code Search methods to program this
remote (See Code Search on page 8).
For a description of each key on the
remote control, refer to the ey
Descriptions section on page 3-4.
In order for the 3-component universal remote to control
your TV, you must program it with the TV code that matches
your TV. These instructions explain the preferred method of
programming the remote—the Direct Entry method.
CODE
SEARCH
INDICATOR
LIGHT
(BLINK)
TV

6
Program for DVD or VCR—
D rect Entry Method
VCR•
DVD
1. Manually turn on the VCR or
DVD player.
2. Locate the enclosed VCR or
DVD Code List. Find your brand
in the VCR Codes or DVD Codes
section, respectively.
Note: If your brand isn’t listed, use one
of the Code Search methods to program
this remote control (See Code Search
on page 8).
3. Press and hold the CODE SEARCH
key until the indicator light illuminates.
Then release the CODE SEARCH key.
4. Press and release the VCR•DVD key.
The indicator light blinks and then
remains lit.
5. Use the number keys on the remote to
enter the first code listed for your brand.
After you enter a valid four-digit
code, the indicator light turns off.
Note: If you enter an invalid code,
the LED will flash rapidly for 2
seconds. Start over at step 3.
6. Aim the remote at the component
(VCR or DVD player). Press the
ON•OFF key. If your VCR or DVD
player turns off, you have found the
correct code.
7. Enter the code in the box provided
on this page for future reference.
8. If your VCR or DVD player doesn’t
turn off, repeat steps 3-6 above,
entering the next code for your brand.
If none of the codes work or your
brand is not listed, use one of the
Code Search methods to program this
remote (See Code Search on page 8).
For a description of each key on
the remote control, refer to the ey
Descriptions section on page 3-4.
In order for the 3-component universal remote to control your
DVD or VCR, you must program it with the code that matches
your component. The VCR•DVD key can be programmed
to operate either a DVD or a VCR player. These instructions
explain the preferred method of programming the remote—
the Direct Entry method.
ON•OFF
(BLINK)
(OFF)
CODE
SEARCH
INDICATOR
LIGHT
VCR OR DVD CODE

7
Program for Satell te, Cable Box or
D g tal TV Converter—D rect Entry Method
SAT•
CBL•DTC
1. Manually turn on the satellite
receiver, cable box or digital TV
converter.
2. Locate the enclosed Code Lists. Find your
brand in the Satellite, Cable Box or Digital
TV converter codes.
Note: If your brand isn’t listed, use
one of the Code Search methods to
program this remote control (See Code
Search on page 8).
3. Press and hold the CODE SEARCH
key until the indicator light illuminates.
Then release the CODE SEARCH key.
4. Press and release the SAT•CBL•DTC
key. The indicator light blinks and
then remains lit.
5. Use the number keys on the remote to
enter the first code listed for your brand.
After you enter a valid four-digit
code, the indicator light turns off.
Note: If you enter an invalid code, the
LED will flash rapidly for 2 seconds.
Start over at step 3.
6. Aim the remote at your satellite
receiver, cable box or digital TV
converter and press the ON•OFF key. If
your device turns off, you have found
the correct code.
7. Enter the code in the box provided
on this page for future reference.
8. If your device doesn’t turn off, repeat
steps 3-6 above, entering the next code
for your brand.
If none of the codes work or your
brand is not listed, use one of the
Code Search methods to program
this remote (See Code Search on page 8).
For a description of each key on the
remote control, refer to the ey
Descriptions section page 3-4.
In order for the 3-component universal remote to control
your satellite, cable box or digital TV converter, you must
program it with the code that matches your component. The
SAT•CBL•DTC key can be programmed to operate either a
satellite receiver, cable box or digital TV converter.
These instructions explain the preferred method of
programming the remote—the Direct Entry method.
ON•OFF
(BLINK)
(OFF)
CODE
SEARCH
INDICATOR
LIGHT
SATELLITE, CABLE
BOX OR DIGITAL TV
CONVERTER CODE

8
Code Search Methods
Manual Code Search
1. Turn on the component you
want the remote to operate.
2. Press and hold the CODE SEARCH
key until the indicator light
illuminates. Then release the
CODE SEARCH key.
3. Press and release the component key
that corresponds to the component
you want the remote to operate
(TV,VCR•DVD or SAT•CBL•DTC).
The indicator light blinks once
and then remains lit.
4. Aim the remote at the component and
press the ON•OFF key continuously
until the component turns off.
Important: Because there are so many
codes, you may have to press the
ON•OFF key many times—possibly
up to 200 times.
5. When the component turns off, press
the ENTER key to store the code.
6. Use Code Retrieval on the next
page to identify the code for your
component for future reference.
If your component’s brand isn’t listed in the Code List or
you have tried all of the codes for your brand and the remote
does not operate your component, use one of the Code Search
methods below—Manual Code Search or Auto Code Search.
Both Code Search methods search all of the codes because
your component’s code may be listed under another brand
in the code list.
Note: The Code Search method may take a long time because
the remote searches all of the codes in its memory for the
code which operates your component. Therefore, if your
brand is listed in the Code List, use the Direct Entry method
described on pages 5-7.
SAT•
CBL•DTC
VCR•
DVD
TV
Auto Code Search
1. Turn on the component you
want the remote to operate.
2. Press and hold the CODE SEARCH
key until the indicator light
illuminates. Then release the
CODE SEARCH key.
3. Press and release the component key
that corresponds to the component
you want the remote to operate
(TV,VCR•DVD or SAT•CBL•DTC).
The indicator light blinks once
and then remains lit.
INDICATOR
LIGHT
CODE
SEARCH
ON•OFF
(BLINK)
INDICATOR
LIGHT
CODE
SEARCH
ENTER
SAT•
CBL•DTC
VCR•
DVD
TV

9
1. Press and hold the CODE SEARCH
key until the indicator light illuminates.
Then release the CODE SEARCH key.
2. Press and release the component
key that matches the component’s
code you are retrieving (TV,VCR•DVD,
or SAT•CBL•DTC). The indicator
light blinks once and then remains lit.
3. Press and release the CODE SEARCH
key. The indicator light turns off.
4. Starting with 0 on the keypad, press
the number keys in order (0-9) until
the indicator light blinks.
5. The number that causes the indicator
light to blink is the first digit of
your code.
6. Repeat step 4 until you have retrieved
all four numbers of the code.
7. Refer to the code box to write down
the code for your component within
the Direct Entry Section (pages 5-7)
for the component just programmed.
If you used one of the Code Search methods to program
your remote, follow the steps below to find out which code
is compatible with your component. Finding the actual code
and writing it down will save you time if you ever need to
program the remote again.
INDICATOR
LIGHT
(OFF)
VCR•
DVD
TV
CODE
SEARCH
CODE
SEARCH
Code Retr eval
(BLINK)
(BLINK)
4. Aim the remote at the component
and press the ON•OFF key once.
The remote automatically sends every
code for the specified component
one at a time, with a 3-second delay
between each code. eep the remote
aimed at the component throughout
the process.
5. As soon as the component turns off,
you must press the ENTER key
immediately so the remote stores the
correct code. If you don’t press ENTER
within 3-seconds, the remote will send
the next code in the list, and you will
have to start over from step 2.
6. Use Code Retrieval to identify the code
for your component for future reference.
ENTER
ON•OFF
(BLINK)
SAT•
CBL•DTC

10
PROGRAMMING SLEEP FEATURE
1. Press and hold the SLEEP key until
the indicator light illuminates. Release
the SLEEP key.
2. Enter time in minutes using the
numerical key pad. The indicator
light should turn off. (Minute 1 thru
9: press 0 before the actual number.
Maximum: 99 minutes).
3. Leave remote aimed at television.
(Sleep Feature will not work unless
remote is left aimed at television.)
CANCELING THE SLEEP TIMER
The Sleep Timer program will be
canceled and reset to zero by either
of the following.
1. Press and hold the SLEEP key
until the indicator light blinks.
2. Press the ON•OFF key,
turning TV off.
This feature will automatically turn off your
TV at a duration you choose from 1 to 99 minutes.
Sleep Feature (Select Models Only)
INDICATOR
LIGHT
ON•OFF
(BLINK)
SLEEP
SLEEP
This remote cannot access every menu system of all models
and brands of consumer electronics components. However,
if you’ve successfully programmed the VCR•DVD key to
operate a DVD player, you can access DVD disc menus
with the MENU key.
The MENU key will also access TV menu systems for
most RCA, GE and PROSCAN TV's, as well as some other
popular brands. Also, some RCA VCR menus are supported
by this remote’s menu key. This remote also supports select
satellite receiver menus.
If this remote’s MENU key doesn’t access the menu system
for your component, you’ll need to use the original remote
to change menu settings.
Note: This remote’s MENU key doesn’t support cable box
menu systems and some VCR menu systems.
Us ng On-screen Menus
OR

11
Hi hli htin and Selectin Menu Items
To navigate On-screen Menus, use the VOL UP/DOWN
and/or CHAN UP/DOWN keys.
VOL UP/DOWN keys move the cursor (or the highlight)
right/left. CHAN UP/DOWN keys move the cursor (or the
highlight) up/down.
For RCA, GE or PROSCAN products, press the MENU or
ENTER key to select the highlighted item. If menu items have
numbers next to them, you can use the number keys to select
an item. Additionally, the ENTER key can be used to select
menu choices.
For Sony products, pressing the ENTER key while
in Menu Mode returns you to the previous menu.
MENU
1. Make sure your components
are turned on and your TV
is set to the component's input.
2. Press the component key on
the remote (TV,VCR•DVD
or SAT•CBL•DTC).
3. Press the MENU key. The indicator
light blinks continuously to indicate
the remote is in Menu Mode and the
component’s menu should appear
on the TV screen.
VCR•
DVD
TV
(BLINK)
Notes:
All functions in competitive models and brands
of products may not be fully supported.
The remote will automatically time out in Menu
Mode and the indicator light will stop blinking after
approximately 10 seconds of inactivity (no keys being
pressed). For DVD menus, the Menu Mode will time
out after approximately 15 seconds.
Because of the wide variety of menu formats,
some experimenting may be required.
Exitin a Menu System
To exit Menu Mode, press the corresponding component
key on the remote (TV,VCR•DVD or SAT•CBL•DTC).
The indicator light goes out and the remote reverts to its
normal mode of operation.
This is an examp e of a DVD disc On-screen Menu.
Eng ish is the menu choice high ighted. Using this
remote contro , you wou d press the ENTER key
to se ect Eng ish.
To high ight another anguage, you wou d press the
CHAN DOWN key (In the examp e above, the high ight
wou d move to Españo ).
Accessin a Menu System
SAT•
CBL•DTC

12
Troubleshoot ng
Problem: The remote can’t be programmed to operate
your component.
• You may be too far away from the component or at a
wrong angle. This remote uses IR (infrared) technology
to communicate with components. The remote sends
the code and the component’s IR sensor reads the code.
Therefore, there must be an unobstructed path between the
remote and the IR sensor on the component. Move closer and
make sure you point the remote at the component (VCR or
DVD player when programming the VCR•DVD key; TV
when programming the TV key; cable box, satellite receiver or
digital TV converter when you’re programming the
SAT•CBL•DTC key).
• If you’ve entered all of the codes for your brand that
are in the accompanying Code List and followed the
instructions, try one of the Code Search methods
(See Code Search on page 8)
• You must put the remote in the correct mode by pressing
the corresponding component key (TV,VCR•DVD,
SAT•CBL•DTC) so the remote knows which component
you want to operate.
• To program the 3 component universal remote to operate
a combination unit (TV/VCR or TV/DVD), first try the
VCR or DVD codes for your brand. Some units, however,
require that you program both the TV (using the TV
codes) and the VCR or DVD (using the VCR or DVD
codes) for full operation.
Problem: The indicator light doe not light when you pre a key.
• You must put the remote in the correct mode by pressing
the corresponding component key (TV,VCR•DVD,
SAT•CBL•DTC) so the remote knows which component
you want to operate.
• You may have pressed an invalid key for the mode the
remote is in (for example, REC only works in VCR Mode).
• Make sure the batteries are properly installed.
• Replace the batteries with two new AAA batteries.
Problem: The remote doe not operate your component.
• You must put the remote in the correct mode by pressing
the corresponding component key (TV,VCR•DVD,
SAT•CBL•DTC) so the remote knows which component
you want to operate.
• Remove any obstacles between the remote and the
component. Make sure to aim the remote at the
IR sensor on the component.
• Make sure the batteries are properly installed
(See Battery Installation on page 3).
• Replace the batteries with two new AAA batteries.

13
If you have further que tion , plea e vi it
www.rcaacce orie .com.
Problem: The remote i not performing command properly.
• You must put the remote in the correct mode by pressing
the corresponding component key (TV,VCR•DVD,
SAT•CBL•DTC) so the remote knows which component
you want to operate.
• Make sure component is “ready” (e.g., DVD player has
disc loaded; VCR has tape loaded, etc.)
• You may have pressed an invalid key for the mode the
remote is in (for example, REC only works in VCR mode).
• If you’re trying to turn on an RCA, GE or PROSCAN
component, press the component key (TV,VCR•DVD,
SAT•CBL•DTC) instead of the ON•OFF key.
• If operating a VCR to record, you must press the REC key
two times.
• If you’re trying to change channels, try pressing the
ENTER key after entering the channel number as
this is a requirement of certain models and brands.
• There is a possibility that a programmed code may only be
able to control some of your component features (e.g., only
turns a component on and off). Follow the steps provided
for programming the remote (See Programming Sections
on pages 5-7). If the component can be turned on and off,
make sure you press the CHAN UP/DOWN key to see if the
component responds. If not, try the next code from the list.
Problem: The VCR won’t record.
• As a safety feature, you must press the REC key twice
to begin recording.
• Make sure the tape is properly loaded in the VCR.
• Make sure the tape is not write-protected. If the safety tab
is removed the tape is write-protected and you cannot
record onto that tape.
Problem: The remote will not change channel .
• You must put the remote in the correct mode by pressing
the corresponding component key (TV,VCR•DVD,
SAT•CBL•DTC) so the remote knows which component
you want to operate.
• Press the ENTER key after you enter a channel number.
Problem: The component’ menu doe n’t appear on
the TV creen.
• The TV must be tuned to the Video Input that matches the
manner in which you connected the component to the TV.
For example, if you connected your DVD player to your
TV by connecting audio/video cables (usually color-
coded yellow, red, and white) to the TV’s Input 1 jack,
you must tune the TV to its Video Input 1 channel.
Remember, different manufacturers label these jacks
differently. Consult the instruction manual that came
with the TV for more information.
• You must put the remote in the correct mode by pressing
the corresponding component key (TV,VCR•DVD,
SAT•CBL•DTC) so the remote knows which component
you want to operate.
• Menu access isn’t supported for all brands. If that’s
the case, you’ll need to use your original remote control
to access menu functions for these components.

14
Audiovox Electronics Corporation (the “Company”) warrants
to the original retail purchaser of this product that should this
product or any part thereof, under normal use and conditions,
be proven defective in material or workmanship within 90
days from the date of original purchase, such defect(s) will be
repaired or replaced with a new or refurbished product (at the
Company’s option) without charge for parts and repair labor.
To obtain repair or replacement within the terms of this
Warranty, the product along with any accessories included in
the original packaging is to be delivered with proof of
warranty coverage (e.g. dated bill of sale), specification of
defect(s), transportation prepaid, to the Company at the
address shown below. Do not return this product to the
Retailer.
This Warranty is not transferable and does not cover product
purchased, serviced or used outside the United States or
Canada. The warranty does not extend to the elimination of
externally generated static or noise, to costs incurred for the
installation, removal or reinstallation of the product.
The warranty does not apply to any product or part thereof
which, in the opinion of the company, has suffered or been
damaged through alteration, improper installation,
mishandling, misuse, neglect, accident or exposure to moisture.
THE EXTENT OF THE COMPANY’S LIABILITY UNDER
THIS WARRANTY IS LIMITED TO THE REPAIR OR
REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT,
SHALL THE COMPANY’S LIABILITY EXCEED THE
PURCHASE PRICE PAID BY PURCHASER FOR THE
PRODUCT. This Warranty is in lieu of all other express
warranties or liabilities. ANY IMPLIED WARRANTIES,
INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED TO DURATION OF THIS
WARRANTY. ANY ACTION FOR BREACH OF ANY
WARRANTY HEREUNDER, INCLUDING ANY IMPLIED
WARRANTY, MUST BE BROUGHT WITHIN A PERIOD OF
18 MONTHS FROM THE DATE OF ORIGINAL PURCHASE.
IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES
WHATSOEVER. No person or representative is authorized to
assume for the Company any liability other than expressed
herein in connection with the sale of this product.
Some states/provinces do not allow limitations on how long
an implied warranty lasts or the exclusion or limitation of
incidental or consequential damage so the above limitations or
exclusions may not apply to you. This Warranty gives you
specific legal rights and you may also have other rights which
vary from state/province to state/province.
U.S.A.: Audiovox Electronics Corporation, 150 Marcus Blvd.,
Hauppauge, New York 11788
CANADA: Audiovox Return Center, c/o Genco, 6685 ennedy
Road, Unit 3, Door 16, Mississauga, Ontario L5T 3A5
90-Day L m ted Warranty

15
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable
d(nickel-cadmium) batteries.
• Always remove old, weak or worn-out batteries promptly
aiand recycle or dispose of them in accordance with Local and
aiNational Regulations.
Battery Precaut ons
• eep the remote dry. If it gets wet, wipe it dry immediately.
• Use and store the remote only in normal temperature
aienvironments.
• Handle the remote gently and carefully. Dont drop it.
• eep the remote away from dust and dirt.
• Wipe the remote with a damp cloth occasionally to keep it
ailooking new.
• Modifying or tampering with the remotes internal
aicomponents can cause malfunction and invalidate its
aiwarranty.
Care and Ma ntenance