RD WORKS FP405R-QA User manual

Electric Fireplace Insert with Heater
OWNER’S MANUAL
Model No. FP405R-QA
PLEASE SAVE THESE INSTRUCTIONS
WARNING: READ THIS OWNER’S MANUAL CAREFULLY BEFORE USE.
PET OWNERS WARNING:
The health of some small pets including birds are extremely sensitive to the
fumes produced during the first-time use of many appliances. These fumes are
not harmful to humans but we recommended that you do not use your heater
around birds and small pets during its initial use until the manufacturing
corrosion coatings burn off.
Customer Service: 1-888-538-008
Service Email: serv[email protected]

2
Thank you for choosing our Electric Fireplace. This owner’s manual will provide you with
valuable information necessary for the proper care and maintenance of your new
product. Please take a few moments to thoroughly read the instructions and familiarize
yourself with all the operational aspects of your new heater.
IMPORTANT INSTRUCTIONS
When using this electric unit, basic safety precautions should always be followed to
reduce the risk of fire, electric shock, and injury to persons, including the following:
1. Read ALL instructions before using this unit.
2. CAUTION: Risk of Electric Shock. DO NOT open or try to repair the heater by
yourself.
3. This heater may get hot when in use. To avoid burns, DO NOT let bare skin
touch hot surfaces. If provided, use handles when moving this heater.
4. Keep combustible materials, such as furniture, pillows, bedding, paper, clothes,
and curtains at least 3 ft from the front of the heater and keep them away from
the sides, top, and rear. DO NOT place towels or other objects on the heater.
5. Extreme caution is necessary when any heater is used by or near children or the
disabled, or when the heater is left operating and unattended.
6. DO NOT operate any heater with a damaged cord or after the heater
malfunctions, has been dropped or damaged in any manner. Return heater to
authorized service facility for examination, electrical or mechanical adjustment,
or repair.
7. This heater is not intended for use in bathrooms, laundry areas and similar
indoor locations. NEVER locate heater where it may fall into a bathtub or other
water container. To protect against electrical hazards, DO NOT immerse in
water or other liquids.
8. DO NOT touch the control panel or plug with a wet hand.
9. DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners,
or similar coverings. Arrange cord away from traffic area and where it will not be
tripped over.
10.DO NOT insert or allow foreign objects to enter any ventilation or exhaust
opening as this may cause an electric shock or fire, or damage the heater.
11.To prevent a possible fire, DO NOT block the air intakes or exhaust in any
manner. DO NOT use on soft surfaces, like a bed, where openings may become
blocked.

3
12.A heater has hot and arcing or sparking parts inside. DO NOT use in areas
where gasoline, paint, explosive and/or flammable liquids are used or stored.
Keep unit away from heated surfaces and open flames.
13.Always plug heaters directly into a wall outlet receptacle. Never use with an
extension cord or relocatable power tap (outlet/power strip).
14.To avoid fire or shock hazard, plug the unit directly into a 120 V AC electrical
outlet.
15.To disconnect heater, turn controls to OFF, then remove plug from outlet. Pull
firmly on the plug, DO NOT unplug by pulling on the cord.
16.Always unplug the unit before moving or cleaning, or whenever the heater is not
in use.
17.Use only for intended household use as described in this manual. Any other use
not recommended by the manufacturer may cause fire, electric shock, or injury
to persons. The use of attachments not recommended or sold by unauthorized
dealers may cause hazards.
18.Always use on a dry, level surface. Use on floor only.
19.DO NOT use outdoors.
20.WARNING: To reduce the risk of fire or electric shock, DO NOT use this unit
with any solid-state speed control device.
21.DO NOT attempt to repair or adjust any electrical or mechanical functions on this
unit. Doing so will void your warranty. The inside of the unit contains no user
serviceable parts. Qualified personnel should perform all servicing only.
SAVE THESE INSTRUCTIONS
SPECIFICATIONS
Voltage Rating
120V (60Hz)
Power
Consumption
1500W
Unit Size
29.07in. (W) x10.94in. (D) x 22.65in. (H)
Unit Weight
18.3KG

4
SAFETY FEATURES
Overheat Safety Feature
This heater is equipped with a overheat safety feature. When the heaters internal
components reach a certain temperature that could cause overheat and possible fire,
the heater will automatically shut off.
WARNING: It is normal for the power cord to feel warm to the touch; however, a loose
fit between the outlet and the plug may cause overheating of the plug. If this occurs, try
inserting the plug into a different outlet. Contact a qualified electrician to inspect the
original outlet for damage.
IN THE BOX
·INFRARED FIREPLACE
·REMOTE CONTROL (2 AAA Batteries Not Included)
·INSTRUCTION BOOKLET
PRODUCT DIAGRAM
Main switch
Air out let
Control panel
Carbon bed
Mantel

5
1、Power indication light: After electrifying show red, press the power button to display
the red light and flame open.
2、Power button: Powers the display on and off.
3、Signal-receiving window: For receiving remote control signal.
4、Low range mode lights: Low range mode indicator lights up for low-grade heat.
5、Heater button: Set up the heater mode and turn off the heat.
6、High range mode lights: High range mode indicator lights up for high-grade heat.
7、Digital display: Indicate set room temperature or time value according to the timer or
High and low heating mode display. After 5 seconds, the display
window automatic blanking, press any key to the window
automatically display except for the power button
8、Celsius indicating light
9、Fahrenheit indicating light
10、℃/℉Button (Button for alternating between Fahrenheit and Celsius).
11、Down button：For setting temperature or time downward
12、Up button: For setting temperature or time upward
13 、Timer button: User setting timing boot or shutdown
14、Timer light
15、Flame light button: Adjust the brightness of the flame
16、Flame light

6
PREPARATION
Place the heater on a firm, level surface and plug into a 120V 60Hz power outlet. Only
operate heater in upright position with caster wheels attached.
Insert 2 AAA batteries into the remote control before using (Batteries Not Included)
OPERATING YOUR HEATER
Once the Electric fireplace has been properly assembled and connected to an
electrical outlet and make sure the main switch is "ON"(main switch light is
shining).it is ready to operate:
1、Start and select working mode
Power button: Powers the display on and off.
Flame light button: Adjust the brightness of the flame
Heater button: Set up the heater mode and turn off
Timer button: User setting timing
℃/℉Button (Button for alternating between Fahrenheit and
Celsius) the heat
Down button：For setting temperature or time downward
Up button: For setting temperature or time upward
Remote Control

7
Or POWER
Turn the heater on by pressing the ON/OFF button on the
control panel or by pressing the Power button on the
supplied remote control.
Once power is off, heating element will stop working at
first. Fan will prolong working for 3min to emit plenty of
heat inside. Then shut OFF automatically.
Or
Select a heat setting.
Press the HEATER button to toggle between the two heat
settings.
Power for heat-up mode is 1500W; heat-down is 1000W,
and turn off the heat.
2、Setting room temperature
Or
Adjust the thermostat by pressing the arrows on the control
panel or remote control.
Set temperature indication varies from 59℉to 95℉，or
from 15℃to 35℃. Once you have chosen the desired
temperature, the heater will remain on until the room
temperature increases to the temperature on the digital
display. The heater will cycle on and off to maintain the
desired room temperature.
Or
Press ℃/℉button, then digital display will indicate
Fahrenheit value or Celsius value.
When Fahrenheit indicating light’s on, digital display
indicates Fahrenheit value,
When Celsius indicating light’s on, digital display
indicates Celsius value.
3. Setting flame

8
Or
Adjust the brightness of the flame and turn off
4. Setting timer-power- off
Caution! ONLY under power-on mode you can set timer-power-off function.
Or
When starting the unit, press the timer button on the
control panel.
Adjust the time by pressing the arrows on the control panel
or remote control.
Digital display turns set temperature to time value for the
timer. Press the UP or DOWN button more than once, the
value will vary from 0 to 12hr (1 hr interval) in circulation.
The light is on when timer –power-off is set.
5、Setting timer-power-on
Caution! ONLY under power-off mode you can set timer-power-on function.
Under power-off, press the timer button on the control
panel.
Adjust the time by pressing the arrows on the control panel
or remote control.
Digital display indicates time value for the timer. Press the
UP or DOWN button more than once, the value will vary
from 0 to 12hr (1 hr interval) in circulation.
The light is on when timer –power-on is set.
6、Setting electro lock
Function of electro lock can avoid operation from children. Locking can be set in both
power-on and power-off modes.

9
And
Press Temp Up and Temp Down buttons once for 3
seconds. Locking is fulfilled when a buzzer rings. When
locked, control panel and remote control failed to function.
When release is needed, please re-press Temp Up and
Temp Down buttons once for 3 seconds. Release is fulfilled
when a buzzer rings. Lock indication disappears. Control
panel and remote control return to function.
MAINTENANCE
1. Glass Information
* Under no circumstances should this product be operated with missing or broken glass.
* Do not strike or slam the glass.
* Do not use abrasive cleaners to clean the glass.
* Replacement glass is available from the manufacturer and replacement should be
carried out by a qualified service person.
2. Cleaning
*To clean the unit, first turn off controls on unit and unplug unit from power source.
*To clean the glass door: remove dust with clean dry cloth or to remove finger prints and
other marks clean glass with clean damp cloth. Do not use abrasive cleaners or spray
liquids on glass door surfaces.
*Metal and metal painted parts should be cleaned with clean damp cloth only. Do not
use abrasive cleaners or spray liquids on this surface.
3. If you do not use the heater for a long time, please take out the remote batteries (to
prevent corrosion) as shown below. Store the remote in a safe place.
TROUBLE SHOOTING
If the heater will not operate, please check the following before seeking repair of service:
1. Check if the power cord is plugged into an electrical outlet, if not, plug in.
2. Check if electricity to the outlet is working.
3. Check the power switch is open
STORAGE
Store the heater in a cool, dry location when not in use. To prevent dust and dirt build-
up, use the original packaging to repack the unit.
PUSH
lid
Battery

10
WARRANTY INFORMATION
This product carries a one (1) year warranty against defects in workmanship and
materials. Hometech agrees to replace a defective product, within the stated
warranty period, when returned to the place of purchase with proof of purchase.
This product is not guaranteed against wear or breakage due to misuse and/or
abuse.