Exodraft Xzense User manual

UK Always read and save the instructions!
3111001 Xzense UK 20220215

3111001 Xzense UK 20220215
Table of Contents
1. Product information 4
1.1. Content of the package 4
1.2. Accessories 4
1.3. Application 4
1.4. Function - with temperature sensor activated 5
1.5. Function - with temperature sensor deactivated 5
1.6. Shipping 5
1.7. Warranty 5
2. Setup 6
2.1. Mounting 6
2.2. General use of the control panel 8
2.3. Generally add/delete devices 10
2.4. Add/pair with Power Unit 12
2.5. Test of communication/signal 17
2.6. Signal test 17
2.7. Language selection 18
2.8. Lighting and operation 19
2.9. Rere and Afterrun 20
2.10. Turn o the chimney fan 20
2.11. Ventilation 21
2.12. Weather station 22
2.13. System control 22
2.14. eXotelligence 23
2.15. Pairing with smartphone via Bluetooth 24
2.16. Basic features of the app 29
2.17. Ventilation with the app 33
2.18. Weather station in the app 34
2.19. Setup and history in the app 35
2.20. FAQ in the app 39
2.21. Software update 40
3. Accessories - Repeater 42
3.1. Setup - Mounting 42
3.2. Range 42
3.3. Setting up one repeater 42
3.4. Setting up multiple repeater 42
3.5. Technical data 43
4. Accessories - XTP sensor 44
4.1. Setup - Mounting 44
4.2. Electrical connection 44
4.3. Add device/pairing devices 45
4.4. Technical data 45
5. Technical specications 46
5.1. Troubleshooting 46
5.2. Technical data 47
5.3. User and service menu 48
6. Declaration of Conformity 50
CONTENTS
Type ID no. Password
Pairing card (pin code)
Control panel
Power Unit ID
Control panel serial no. *
The serial number is located on the back of the control panel.
If you want to have an overall view of yours units’ ID number
and password, they can be written down here

3
Product information
Signature explanation
The following terms are used in this manual to draw attention to potential risks or important product information:
Danger
Violations of directions indicated by
a prohibition symbol are associated
with a danger to life.
Warning
Violations of instructions indicated by a
hazard symbol are associated with the
risk of personal injury or damage to the
equipment.
Danger
To minimise the risk of re, electric shock or personal injury, please observe the following:
1. Use the device correctly following the ma-
nufacturer’s instructions. If in doubt, contact the
dealer.
2. Prior to servicing the device:
Disconnect the power and ensure it cannot
accidentally be reconnected.
3. Installation work should be carried out by
qualied personnel in accordance with national
regulations.
4. Follow the manufacturer’s instructions for the
device and general safety directions.
5. This device must be earthed.
Disposal
No special precautions. The product should be disposed of in accordance with national rules for the disposal of
electronic waste.
Illustration explanation
Illustration Explanation
Light pres incl. movement on the touch screen.
To the sides or up and down
Light pres on touch screen

4
3111001 Xzense UK 20220215
Product information
1. Product information
1.1. Content of the package
• 1 pcs. control panel Xzense
• 1 pcs. Power unit for mounting on chimney
• 1 pcs. temperature sensor
• 1 pcs. bracket / wall mount
• 1 pcs. bag with two rawl plugs and two screws for tting
• 1 pcs. USB micro charging cable
• 1. pcs. USB-C to USB-A adapter
• Installation and operating instructions
• Quick guides
• Pairing card (pin code) with code for pariring control panel and control box
1.2. Accessories
Additional accessories can be ordered separately
exodraft
item number Item Description
7501001 Repeater
If there is a need to have a Power Unit and Control panel located at
a distance that excludes signal between the units, it is possible to
amplify the signal with a repeater.
7501002 XTP-sensor
(Pressure sensor)
With a wireless XTP sensor, it is possible to keep a constant draft in
the chimney without having to adjust the speed of the chimney.
7501004 USB-charger
If there is a constant supply for the control panel, for example. In
connection with operation via an App from a smartphone, this
requires a USB charger.
1100703 Fittings for mounting on
the steel chimney
If the Power Unit is to be mounted on a steel chimney, a mounting
kit can be purchased
5220000 Additional control panel If you want to be able to control the chimney fan from several
control panels, several can be connected to the same system
1.3. Application
exodraft wireless Xzense control, together with an exodraft chimney fan, is designed for
use with replaces, stoves and solid fuel boilers.
Xzense can start the chimney fan automatically by means of the temperature sen-
sor, but can also be started by using the control panel. The temperature sensor
monitors the replace and informs when to add more fuel. When the temperature drops
further, the chimney fan stops after 30 min. A simple programming of the control makes
it possible to use Xzense optimally, together with either an open replace or a stove/
boiler.
Xzense also allows you to warn against excessive temperature in the chimney.
Ventilation The controller can be used to regulate the chimney fan, even without heat in the
replace, if it is desired to ventilate the room.

5
Product information
1.4. Function - with temperature sensor activated
Start-up function Xzense is activated by pressing the button at the top of the control panel.
The lighting function is selected before lighting the stove/replace.
The chimney fan now starts at the starting speed, boost. After a preset time, the speed is
adjusted down to a lower set level.
The factory setting for boost speed is 100% for 10 min.
The rst time the Xzense is used the speed drops to 50 %. When usedthe next time, the
speed drops to the last used speed.
Automatic startup If you forget to start the chimney fan before lighting, the chimney fan will automatically
start when the temperature reaches the set start temperature at the sensor.
The factory setting is 40°C.
Rering function The Xzense control panel indicates when it is time to add new fuel.
The display lights up and a dialog box comes up while giving an alarm beep.
If you want to rere, select the YES button. Then you rere further by adding more fuel.
When you say YES to rering, the chimney fan creates a maximum boost for 3 minutes,
after which it regulates the speed down again.
Automatic stop After the last ring, the temperature of the chimney will slowly drop. When the tempera-
ture has dropped to the factory default setting, the controller ensures that the chimney
fan stays in operation for a while, to ensure that the last smoke is pulled out, also called
Afterrun. The factory setting for Afterrun is 30 min.
High temperature
warning
The control panel display will light up if the temperature of the temperature sensor
exceeds the set value. The factory setting is 250°C.
All factory settings can be changed and is found under the Setup menu.
1.5. Function - with temperature sensor deactivated (ventilation)
Ventilation If the temperature sensor is not activated in the user menu, the control can be used as a
10-100% regulation of the speed of the chimney fan. Thereby ventilation from the room
can be achieved.
Note Automatic start and stop is also disabled if the temperature sensor is disabled.
1.6. Shipping
Shipping Xzense is sent in secure packaging, along with the Power Unit, with accompanying
instructions.
Standard
packing list
If other components are included, these will appear as separate items on the shipping
package list.
1.7. Warranty
exodraft-products must be installed by qualied personnel. If this is not complied with,
exodraft a/s may claim the right to have the product warranty lapsed wholly or partly.
exodraft reserve the right to make changes to these guidelines without prior notice.

6
3111001 Xzense UK 20220215
Product information
2. Setup
2.1. Mounting
Sending signals Place the Power Unit on the chimney so that the most direct line can be reached.
The Power Unit and the chimney fan must have a maximum distance of 1 meter, so that the
cables can reach.
Range The range between the units should not exceed 18 meters if you want the most optimal
signal. Please note that some building constructions may result in a shorter range. This could
for example be steel reenforced concrete.
Signal The Xzense repeater can extend the working distance between the Power unit and the con-
trol panel. This is useful when the signal shall pass through several storeys.
The signal can at most go through 3 pcs. repeater between an Xzense Power Unit and a
control panel. The repeater is placed between the Xzense control panel and the Power Unit,
which is typically mounted on the chimney.
In some situations, it would be appropriate to set up the repeater outdoors, e.g. under the
overhang or on another building. The signal may have diculties penetrating certain
materials, such as steel and aluminum structures.
Mounting of sensor and Power Unit
Step Action Illustration
1a
Install the sensor on the chimney fan with the
supplied bracket. Drill 2 pcs. 4 mm holes and insert
the screws.
RSV
RS
1b
Mounting with cover ange:
Remove the plug from the tube
cover ange, and insert
sensor. Tighten the screw (A).
(A)
(A)
2a
For brick chimneys:
Drill holes as shown (max. 1 m from the chimney
fan). Remove the lid from the power unit and
mount it on the chimney using rawlplugs and
screws.
Note: Position the device where it has the best line
of sight to the control panel.
Project:
Material:
Date:
Rev.:
Title:
Rev. No.: Ref.:
Format: A3
Weight:
Approved:
Draw. No.:
Sheet:
A
Strømforsyning til EW41
26-08-2010
100260
pmn
DS/EN 22768 m
Unless otherwise specified tolerances are after
0,000 kg
2 of 5
Manufacture
110
90

7
Product information
Step Action Illustration
2b
For steel chimneys:
Remove the lid from the power unit and mount
the bracket (optional extra) using screws and nuts.
Drill 4 mm holes in the chimney and mount the
device using selftapping screws (max. 1 m from
the chimney fan).
Note: Position the device where it has the best line
of sight to the control panel.
3
Connect the wires according to the diagram at the
bottom.
A: Supply voltage (cable with plug attached).
B: Connection to a chimney fan.
C: Building automation
D: Connection to temperature sensor.
When installing cables, wires should be approx. 8
cm free of the jacket.
Note: There must be no power on the
device when connecting wires.
Project:
Material:
Date:
Rev.:
Title:
Rev. No.: Ref.:
Format: A3
Weight:
Approved:
Draw. No.:
Sheet:
A
Strømforsyning tilEW41
26-08-2010
100260
pmn
DS/EN 22768 m
Unless otherwise specified tolerances are after
0,000 kg
3 of 5
Manufacture
A
C
B
4
Attaching armoured hose from chimney fan.
Remove the screw connector from the armoured
hose. Keep the small plastic clamping ring!
E: Fit the nut from the connector from the power
unit.
F: Fit the plastic clamping ring on the armoured
hose.
Attach the armoured hose to the power unit.
Project:
Material:
Date:
Rev.:
Title:
Rev. No.: Ref.:
Format: A3
Weight:
Approved:
Draw. No.:
Sheet:
A
Strømforsyning til EW41
26-08-2010
100260
pmn
DS/EN 22768 m
Unless otherwise specified tolerances are after
0,000 kg
5 of 5
Manufacture
F
E
Wiring diagram
Brown
Blue
Chimney fan
Socket
White Red
Power Unit
Brown Blue
1 2 3
Supply Motor
Green/Yellow
3x1,5
3x1,5
Sensor
Nreg
L1
4 5 6
Blue
Brown
13 14
Temperature sensor
13
14
Red
White
2X0,75
Start/
Stop
7 8 9
10
11
12
0-10V
In
0-10V
Out
D

8
3111001 Xzense UK 20220215
Product information
2.2. General use of the control panel
Function of buttons and touch screen
Action Illustration Example
Display activation
Press the button on the top with one click to
activate the display.
The control panel is activated when it lights up.
The control panel goes into standby/sleep by
pressing the button once more while the
display is on. After approx 10 seconds, the
display will even go into sleep if there is no
activity on the display.
Tap lightly
Tap a nger to navigate the menus, or to change
the values of the properties
MENU
Interface Setup Network
Scroll
Move a nger (up/down or to the sides) across
the screen without lifting it, to scroll up and
down/back and forth in the respective
drop-down menus
OPSÆTNING
Starttemperatur
Stoptemperatur
Boost time
Boost me
Stop temperature
Start temperature
SETUP
Restart or switch o the control panel
To restart the control panel, hold down the
button for approx 4 sec.
A dialog box appears and asks if you want to
restart the control panel.
If you want to switch o its panel completely,
press the button for more than 10 sec.
To reactivate the panel, it needs to be powered
by a USB-charger.

9
Product information
Charging and battery
Action Illustration Example
Charging with USB cable
To charge the control panel, use the USB
connector at the bottom. A charge from the
entire discharged state takes approx 4-5 hours.
The control panel has a service life of approx 30
days of normal use with deactivated bluetooth
communication for a smartphone *.
*It is recommended that the control panel charger plug is
always used when Bluetooth is enabled as the life of the
battery is signicantly reduced when using the smart-
phone and the bluetooth function.
Mounting of control panel
Step Action Illustration
1
Mark the distance on the wall from the steel plate.
Drill 2 holes with a diameter of 6 mm
Insert rawlplugs and mount the steel plate in the two
holes with two screws.
2 Slide the plastic bracket outside the steel plate
3
Fit the stop at the end of the bracket
The Xzense control panel can now be placed on the wall
bracket

10
3111001 Xzense UK 20220215
Product information
2.3. Generally add/delete devices
Add devices
Step Action Display
1
To add a device (Power Unit, etc.), select the Add Device
menu.
Note: a repeater shall only be turned on and not connected
in UNITS menu.
KOMMUNIKATION
SignalastyrkeTilføj enhed Nulstil netværk
Devices Signal test Reset network
SIGNAL
2
Already paired devices are displayed on the screen with a
trash can beside.
To pair with a new device, select a device with a link beside.
Power Unit
Repeater
Tilføj enhed
Power Unit (F1EE)
Repeater
UNITS
3
If the desired device you want to pair with is not available,
you can add the device via. code-pairing.
Select the Add Device feature + .
Note: the power unit must be turned on.
Power Unit
Repeater
Tilføj enhed
Power Unit (F1EE)
Repeater
UNITS
4
If you want to pair with a Power Unit, you must
enter the correct code from the pairing code card that
came with the Power Unit.
Use the arrows to navigate the numbers and use the plus
and minus icons to increase or decrease the value of the
number. Finish with OK.
INDTAST KODE
29 54
OK
PIN CODE
5
The code consists of four characters.
Number from 0-9 and/or letters from A-F.*
*The password illustrated to the right is just an example.
DeviceID: F1EC
PW: 9186

11
Product information
Delete paired devices
Step Action Display
1If you want to delete a paired device, select the trash can
icon to delete the pairing.
Power Unit
Repeater
Tilføj enhed
Power Unit (F1EE)
Repeater
UNITS
2A dialog box appears, and you nally conrm with YES if
you want to delete the pairing to the device.
Power Unit
Repeater
Tilføj enhed
Power Unit (F1EE)
Repeater
UNITS
Disconnect the
Power Unit (F1EE)?
YES NO

12
3111001 Xzense UK 20220215
Product information
2.4. Add/pair with Power Unit
It is possible to pair the control panel and Power Unit in three dierent ways.
Option 1 - With power within two minutes after power is applied to the power unit
Step Action Display
1
Within the rst two minutes after the power is
connected to the Power Unit, the control panel can be
connected without the use of ID or code.
The connection can thus be made by using Add device,
which is found in the start menu.
Ventilation
Vejrstation
Tilføj enhed
WeatherAdd device
2
Select the Power Unit with the correct ID under units.
The ID number can be found on the pairing card
enclosed with the Power Unit.
Power Unit
Repeater
Tilføj enhed
Power Unit (F1EE)
Repeater
UNITS
3If the connection has been made correctly,
the control panel will report the pairing again.
Power Unit
Repeater
Tilføj enhed
Power Unit (F1EE)
Repeater
UNITS
The devices are
now paired!
OK

13
Product information
Option 2 - With power and supplied code
Step Action Display
1
If the Power Unit has been connected to power for more
than two minutes, then the pairing must be done using
the password supplied with the Power Unit.*.
*The password illustrated to the right is just an example.
DeviceID: F1EC
PW: 9186
2The connection can thus be made by using Add device,
which is found in the start menu.
Ventilation
Vejrstation
Tilføj enhed
WeatherAdd device
3
Select the Power Unit with the correct ID under units.
The ID number can be found on the pairing card
enclosed with the Power Unit.
Power Unit
Repeater
Tilføj enhed
Power Unit (F1EE)
Repeater
UNITS
4
Then enter the supplied code and end with OK. If the
connection has been made correctly, the control panel
will announce that the pairing has been completed.
INDTAST KODE
29 54
OK
PIN CODE

14
3111001 Xzense UK 20220215
Product information
Option 3 - With power and press button in Power Unit
Step Action Display
1
If the Power Unit has been connected to power for more
than two minutes and the password has been lost, then
the pairing can be done by pressing the connection
button inside the Power Unit for approx 5 seconds (see
illustration on next page - under the Power Unit section).
2The connection can thus be made by using Add device,
which is found in the start menu.
Ventilation
Vejrstation
Tilføj enhed
WeatherAdd device
3
Select the Power Unit with the correct ID under units.
Note: If the button in the power unit has been pressed
correctly, the chain icon is faded.
Power Unit
Repeater
Tilføj enhed
Power Unit (F1EE)
Repeater
4If the connection has been made correctly,
the control panel will report the pairing again.
Power Unit
Repeater
Tilføj enhed
Power Unit (F1EE)
Repeater
UNITS
The devices are
now paired!
OK

15
Product information
Power Unit
Features
AIsolation switch for the chimney fan.
0502300
Serie no.: xxxx
Batch no: xxxx
CONNECT
POWER
E
C
D
B
A
BLED indicators:
POWER lights up continuously when voltage is
applied to the Power Unit.
CONNECT lights up when searching for a
device.
CButton to connect:
The control panel and Power Unit can be
connected.
Press the button (C) on the Power Unit
for more than 5 sec.
DFuse: Secure the chimney fan against overload.
EThe Power Unit serial number (located on the
inside of the box)

16
3111001 Xzense UK 20220215
Product information
Power Unit MAC address
Step Action Display
1 Go to the Devices menu in the Signal menu.
KOMMUNIKATION
SignalastyrkeTilføj enhed Nulstil netværk
Devices Signal test Reset network
SIGNAL
2Long press on the Power Unit.
Power Unit
Repeater
Tilføj enhed
Power Unit (F1EE)
Repeater
UNITS
3Then the MAC address will be shown on the display.
Press OK to return the Devices menu.
Power Unit
Repeater
Tilføj enhed
Power Unit (F1EE)
Repeater
UNITS
Ventilation
OK
MAC
F1EE:46FE:FF6F:0D00

17
Product information
2.5. Test of communication/signal
Step Action Display
1
Turn on the control panel by clicking the button on the
top.
Plug in the USB-cable if needed.
2
The screen now lights up on the home screen.
If the display shows the text ”No connection to Power
Unit”, there is no communication between the power
unit and control panel. Try moving the control panel for
better contact.
See the section on Setup - Mounting,
for more information.
Optænding Ventilation Vejrstation
OK
Error 1
No connection to
Power Unit
3
Good mounting position
If you want to mount the wall bracket in order to have a
station for the control panel, it must be ensured that the
unit can receive signal from this location.
Always check if there is a signal before mounting, by
pressing the signal icon under the Signal Test.
SIGNAL TEST
Waiting for client..
------ results ------
2.6. Signal test
Step Action Display
1
To test the signal strength, enter the Signal Test menu,
which is available using the following menu:
1. General
2. Network
3. Communication
4. Signal test
KOMMUNIKATION
SignalastyrkeTilføj enhed Nulstil netværk
Devices Signal test Reset network
SIGNAL
2
Press the signal icon and the test starts.
The power unit sends 100 packets to the controlap
lanel, and the result of this transmission can be seen
after in the buttom of the screen.
If there are many data packets left, the signal is bad and
you should nd a better place for its control panel.
CRC = Number of packets with CRC error
LOSS = Number of packets lost
RSSI = Received Signal Strength Indicator
PER = Packet Error Rate
1 = Good 100 = Bad
-20 = Good signal -100 = Bad signal
SIGNAL TEST
Receiving from F1EE
Rx: 89/100
CRCs: 0, Loss: 0, RSSI: -60, PER: 0.0

18
3111001 Xzense UK 20220215
Product information
2.7. Language selection
At factory settings, english is selected as the default setting.
It is possible to change the language in the menu, for the control panel.
Step Action Display
1Turn on the control panel by clicking the button at
the top. Select the top menu General.
Lighting Ventilation Weather
2 Select the menu Interface
MENU
Interface Setup Network
3 Select the menu Language
Kontrast Lysstyrke
Language Contrast Brightness Sound
SETTINGS
4
Select the desired language by moving your nger
to the side of the language menu. Click on the
desired language.
To return to the menus, use the back arrow at the
bottom left corner.
DANISH
Language

19
Product information
2.8. Lighting and operation
Step Action Display
1 Select Lighting
Lighting Ventilation Weather
2
The display shows a lighting, and the replace/stove
must now be turned on.
The chimney fan will run at maximum speed for 10
minutes (default setting) and then fall to the speed it
was driving when it was last turned on.
The Boost period and speed can be changed in the
Setup menu.
10 min
BOOSTING
3
Turn on while the chimney fan is running at maximum
speed.
If the temperature sensor is activated and you forget
to turn on the chimney before turning on, the chim-
ney fan will automatically start when the temperature
at the top of the chimney has reached the start tem-
perature setting. The factory setting is 40 oC.
Note: We recommend that the chimney fan shall be
switched on manually every time! At the same time
you avoid soot and ach to escape the replace/
stove during lighting.
10 min
BOOSTING
4
After the boost period, it switches on in operation
mode.
To increase or decrease the chimney speed and hence
the chimney draft, the up and down buttons are used.
The display shows the new setting.
Skorsten
55 C
DRIFT
30 %
OPERATION
Chimney
5
The display automatically goes into sleep mode and
the backlight goes out after a short time. Press the
button on the top of the unit to turn the display back
on.

20
3111001 Xzense UK 20220215
Product information
2.9. Rere and Afterrun
Step Action Display
1
When it’s time to refuel, the display lights up, a small
alarm sounds and a dialog pops up and asks if you
want to refuel.
It is possible to turn on the alarm signal in the menu
Settings.
Det er tid til at genfyrer.
Vil du genfyre nu?
JA NEJ
It is time to refuel
Would you like to refuel now?
YES NO
2
If you want to Rere, press YES in the dialog box before
rere.
In order to avoid soot and smoke in the room, the
chimney fan speed is increased to maximum (boost)
for 3 minutes before decreasing back to the previous
setting. 3 min
REFUELING
3
If you do not want to re-re, NO is
selected and the Afterrun will start.
The afterrun has a factory setting of 30 minutes.
AFTERRUN
30 min
2.10. Turn o the chimney fan
Step Action
A
Ventilation: The chimney fan is switched o by pressing the switch o.
Note: If the temperature sensor is activated, the chimney fan cannot be switched o as long as the temperature at
the chimney fan is higher than the stop temperature setting.
B
Automatic: After the last rering, the temperature in the chimney falls slowly. If the temperature sensor is activated
the chimney fan automatically stops when the temperature in the chimney has fallen below the stop temperature.
The factory setting is 35 °C.
The chimney fan has a Afterrun period of 30 minutes, which ensures that the fuel is glow-free and that the remaining
smoke has been led away from the chimney. Both the stop temperature and the afterrun period can be changed in
the menu.