Town & Country Fireplaces 22150051 User manual

270223-12 SKU# 22150051 100005921
SKU# 22150051
For TCWS54 Series D
Fireplaces
These instructions are supplementary to the Installation
and Operating Instructions supplied with the replace
and should be kept together. Refer to the Installation
and Operating Instructions for proper gas supply, safety
requirements and operating instructions.
TCWS54
TRANQUILITY
BURNER KIT
INSTRUCTIONS
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

Contents of Package
SKU# 22150051_270223-12
2
2 3.4 LBS SAND
1 HARDWARE PACK
2 EQUALIZER ROCKS
2 BURNER ASSEMBLIES
1 BURNER TRAY ASSEMBLY
4 PEBBLE SETS
A
B
C
D
E
F
B
C
A
D
E
F
Figure 1: TCWS54 Black Diamond Burner parts.

Tranquility Burner Installation
SKU# 22150051_270223-12
3
If converting to propane see conversion instructions on page #7 before proceeding.
Install panels according to the TCWS.54CE Installation and
Operating manual prior to burner installation. (Page 23)
1. Install the right burner by tipping into location trough and slipping the venturi tube over the orice. Test for connection by lifting at a
location pin on the right side of the burner. Repeat with left burner.
(Fig. #2)
2. Tilt burner tray length-wise and insert into the rebox. Be sure pilot is attached to burner support rail with screw in rst hole position.
(Fig. #3 & 4)
3. Attach pilot to burner tray. (Fig. #5)
Figure 1: TCWS54 Black Diamond Burner parts.
Figure 2: TCWS54 Black Diamond Burner parts. Figure 3: TCWS54 Black Diamond Burner parts.
Figure 4: TCWS54 Black Diamond Burner parts.
Figure 5: TCWS54 Black Diamond Burner parts.
FIRST HOLE POSITION

SKU# 22150051_270223-12
4
NOTE: check air shutter for correct
fuel setting before proceeding
further. Both burners are the same.
Fully closed for natural gas.
13/64 (0.2)” open for LP.
4. Secure the burner tray to legs using eight screws (Fig. #6)
NOTE: a light will aid aligning the holes in the tray with the leg
CAUTION: The burners should be tightly butted up against each other at the center to ensure correct operation.
5. Place sand into the burner tray and brush smooth. Use caution not to get sand near the burner ports. (Fig. #7)
Figure 6: TCWS54 Black Diamond Burner parts.
Figure 7: TCWS54 Black Diamond Burner parts.

SKU# 22150051_270223-12
5
7. Place each rock as per the following
photographs, start from the right hand
side of the burner and ensure that the
arrow on each rock points towards the
front of the replace. (Fig. #7 to 15)
6. Each rock has a slot in it’s base and is
marked with a letter and an arrow.
(Fig. #8)
Figure 8: Rock markings
Figure 9: Rock A
Figure 10: Rock B
Figure 11: Rock C
Figure 12: Rock D
Figure 13: Rock E
Figure 14: Rock F
Figure 15: Rock G

SKU# 22150051_270223-12
6
WIDE EDGE TO FRONT OF
FIREPLACE
10. Install front porcelain cover (wide edge
should face the front). (Fig. #20)
9. Place the two remaining rocks on the
left hand end of burner as shown.
(Fig. #18 and 19)
8. Repeat the sequence of placing the
rocks three more times until the burner
is covered.
Figure 16: Rock H
Figure 17: Rock J
Figure 18: Rock A
Figure 19: Rock B
Figure 20: Front cover.
A
B
C
D
E
F
G
H
J

Propane Conversion
SKU# 22150051_270223-12
7
WARNING
This conversion kit shall be installed by a qualified service agency in accordance with the
manufacturer's instructions and all applicable codes and requirements of the authority having
jurisdiction.
If the information in these instructions is not followed exactly, a fire, explosion or production of
carbon monoxide may result causing property damage, personal injury or loss of life.
The qualified service agency is responsible for the proper installation of this kit.
The installation is not proper and complete until the operation of the converted appliance is
checked as specified in the manufacturer's instructions supplied with the kit.
If the unit is to be used on propane convert as follows using the components supplied with this burner:
CAUTION
The gas supply and electrical power shall be shut off before proceeding with the conversion.
Note:
Factory supplied components must be used to ensure correct input. After conversion conrm proper manifold pressure.
1. If installed remove the rocks from the burners.
2. If installed remove the burner tray from the manifold brackets. (8 screws)
(Fig. #21)
3. Remove burners by gently lifting up the left end and disengaging from the orice.
4. Using a 1/2” wrench, undo the natural gas burner orice, (marked “NC”). Apply a small amount of pipe joint compound to the threads
of the propane burner orice (marked “LC”) to ensure a good seal, before screwing it into the tting.
Figure 21: Remove tray. Figure 22: Remove NG Orice

SKU# 22150051_270223-12
8
Cet appareil a été converti en gaz propane
Numéro d'assemblage
j m a
Firme
Adresse
l'entreprise désignée
ci-dessus accepte la
responsabilité que cette
conversion a été
correctement faite.
Kit Number
dd mm yy
Company
Address
The above accepts the
responsibility that this
conversion has been
properly performed.
This appliance was converted to propane gas
5052.52001-B
5052.52001-B
Loosen the primary air shutter screw, open shutter to give a gap of 13/64” (0.2”) and re-tighten. Repeat on other burner. (Fig. #23)
5. With a 7/16” wrench loosen the pilot head on the pilot assembly. (Fig. #24)
6. Slide the pilot adjustment band over and ensure that the hole in the orice band is showing.
Fig. #25 shows NG position
Fig. #26 shows LP position).
7. Update the Propane Conversion Label with date and name when nished. (Fig #27)
WARNING: Both the
control box shield and
the access panel must
be reinstalled after
conversion/ installation
or servicing has been
completed. Failure to
do so will overheat and
cause premature failure
of the control system.
For complete conversion valve installation instructions, refer
to the instruction book included in the SIT conversion kit.
MAIN BURNER ORIFICES
(marked “LC”)
Figure 23: Adjust shutter. Figure 24: Adjust shutter.
Figure 25: NG Position. Figure 26: LP Position.
Figure 27: Conversion label.

Gas Pressure Check
SKU# 22150051_270223-12
9
1. Remove the plug from the pressure test port using a 3/16” hex key. The plug is located between the right side lintel and rebox side.
(Fig. #28)
2. Thread the extension test tting into the open port.
(Fig. #29)
3. Attach a pressure gauge onto the
tting.
4. When testing is complete shut off the gas, remove the tting and replace the plug. Thread sealant will be required to ensure a gas tight
connection.
Note: To test the gas pressure, turn off the gas supply before removing the plug from the supply pressure test port or manifold
pressure test port.
Verify gas pressures with the fireplace lit and on the highest setting.
SUPPLY
PRESSURE
MANIFOLD
PRESSURE
Correct gas pressure requirement:
Supply Pressure Natural Gas Propane
Min. Pressure 5.0" WC 12.5" WC
(For purpose of input adjustment)
Max. Pressure 13.9" WC 13.9" WC
Manifold Pressure
Maximum 3.5" WC 10" WC
Minimum 1.6" WC 6.4" WC
Figure 28: Test ports.
Figure 29: Pressure Adjustment.

Figure 30: Conversion label.
Burner Flame Adjustment
SKU# 22150051_270223-12
10
The air shutter on the burner tube controls the primary combustion air. It is set to the closed position at the factory for natural gas fuel. For
LP see Pg.8. Some adjustment may be necessary to obtain desired ame and to eliminate carbon deposits. Evaluate ame appearance
after the replace has reached operating temperature. See Fig. #30 for proper ame pattern.
Open primary air if the window glass and rebox have carbon accumulation and/or the ames are long, dark and stringy. The shutter
may also be opened to lessen the ame height.
NOTE:
Proper air shutter setting is required.
The flame should be just orange and “lazy”. It should NEVER be set to create sooting on internal parts and window glass.

NOT SHOWN
*
*
*
*
Parts Diagram
SKU# 22150051_270223-12
11
ITEM.......DESCRIPTION........................................................................PART NO.
#1..........TRANQUILITY BURNER KIT........................ .............22150051
#2..........PEBBLE ASSEMBLY................................................... 5096.921
#3.......... SAND ..................................................................TC42.SAND34
(Two Bags Per Kit)
#4..........TRIM ROCK “A” 5096.922
#5..........TRIM ROCK “B”..........................................................5096.923
(WHEN ORDERING, INCLUDE PART NUMBER WITH DESCRIPTION)
1
2
KIT CONTENTS:

© 2022 Copyright Pacic Energy Fireplace Products LTD
Reproduction, adaptation, or translation
without prior written permission is prohibited,
except as allowed under the copyright laws.
Printed in Canada
For technical support, please call your retailer.
Web site: www.townandcountryfireplaces.net
2975 Allenby Rd., Duncan, BC V9L 6V8