Record Power SC1 User guide

Original Instruction Manual
SC1 2” Mini Chuck
SC2 2 ½” Mini Chuck
Important
For your safety read instructions carefully before
assembling or using this product.
Save this manual for future reference.
Always wear safety
glasses when using
woodworking
equipment.
Always read the
instructions provided
before using
woodworking
equipment.
Version 3.4
May 2021
To register this product please visit
www.recordpower.info
It is important to register your product as soon as possible in order to receive efficient after
sales support and be entitled to the full 5 year guarantee. Your statutory rights are not
affected. Please see back cover for contact details.
i
Kg

2
Contents
1 Explanation of Symbols
2 General Health & Safety Guidance
3 Additional Health & Safety Guidance for Woodturning Lathes
4 Record Power Guarantee
5 Using the Chuck Safely
6 Intended Use of the Lathe
7 Contents of the Packages
8 Operation
9 Maintenance
10 Parts Lists & Diagrams
11 General Jaw Use
12 62303 40 mm Standard Jaws
13 62301 Dome Jaws
14 62302 Pin Jaws with 6 mm Bore
15 62305 Pen Jaws
16 62571 68 mm (2 11⁄16”) Faceplate Ring

3
The symbols and their meanings shown below may be used throughout this manual.
Please ensure that you take the appropriate action wherever the warnings are used.
1. Explanation of Symbols
Mandatory Instructions Warnings
Read and fully understand the instruction
manual before attempting to use
the machine.
Indicates an instruction that requires
particular attention
Wear protective eyewear
Use respiratory protective equipment
Use suitable protective footwear
Use hearing protection
Use protective work gloves
Indicates a risk of severe personal injury or
damage to the machine
Indicates a risk of severe personal injury from
electrical shock
Risk of personal injury from lifting of heavy
items
Indicates a risk of severe personal injury from
airborne objects
Risk of fire
i
Kg
i
Kg
i
Kg
i
Kg
i
Kg
i
Kg
i
Kg
i
Kg
i
Kg
i
Kg
i
Kg
i
Kg

4
2. General Health & Safety Guidance
Ensure that you carefully read and fully
understand the instructions in this manual
before assembly, installation and use of this
product. Keep these instructions in a safe place
for future reference.
WARNING: for your own safety, do not attempt to
operate this machine until it is completely assembled and
installed according to these instructions.
WARNING: When using any machine, basic safety
precautions should always be followed to reduce the risk
of fire, electric shock and personal injury.
Safe Operation
1. Use Personal Protective Equipment (PPE)
• The operation of any machine can result in foreign
objects being thrown into your eyes, which can result
in severe eye damage. Protective eye wear or other
suitable eye protection or face shield should be used
at all times. Everyday spectacles only have impact
resistant lenses. They are not protective eye wear and
do not give additional lateral protection.
• Use respiratory protective equipment (dust mask etc.)
if the machining operation creates dust. Exposure to
high levels of dust created by machining hardwoods,
softwoods and man made composite boards can result
in serious health problems. Some imported hardwoods
give off highly irritating dust, which can cause a
burning sensation. The use of respiratory protective
equipment should not be seen as an alternative to
controlling the risk of exposure at source by using
adequate dust extraction equipment.
• The use of ear plugs or ear defenders is recommended
when the machine is in use, particularly if the noise
level exceeds 85 dB.
• Wear suitable protective gloves when handling cutting
tools or blades. Gloves should NOT be worn when
using the machine as they can be caught in moving
parts of the machine.
• Non-slip safety footwear is recommended when using
the machine and handling large work pieces.
2. Dress appropriately
• Do not wear loose clothing, neckties or jewellery; they
can be caught in moving parts of the machine.
• Roll up long sleeves above the elbow.
• Wear protective hair covering to contain long hair.
3. Safety warnings
• Find and read any warning labels on the machine.
• It is important that any labels bearing health and
safety warnings are not removed, defaced or covered.
Replacement labels can be obtained by contacting our
Customer Service Department.
4. Familiarise yourself with the machine
• If you are not thoroughly familiar with the operation
of this machine, obtain advice from your supervisor,
instructor, or other qualified person or contact your
retailer for information on training courses. Do not
use this machine until adequate training has been
undertaken.
5. Take care when moving or positioning the
machine
• Some machines can be very heavy. Ensure the floor of
the area in which the machine is to be used is capable
of supporting the machine.
• The machine and its various components can be heavy.
Always adopt a safe lifting technique and seek
assistance when lifting heavy components. In some
cases it may be necessary to use mechanical handling
equipment to position the machine within the work
area.
• Some machines have optional wheel kits available to
allow them to be manoeuvred around the workshop
as required. Care should be taken to install these
according to the instructions provided.
• Due to the nature of the design of some machines the
centre of gravity will be high making them unstable
when moved. Extreme care should be taken when
moving any machine.
• If transportation of the machine is required then all
precautions relating to the installation and handling
of the machine apply. In addition, ensure that any
vehicles or manual handling equipment used for
transportation are of adequate specification.
6. The machine should be level and stable at all
times
• When using a leg stand or cabinet base that is
designed to be fitted to the machine, always ensure
that it is securely fastened to the machine using the
fixings provided.
• If the machine is suitable to be used on a workbench,
ensure that the workbench is well constructed and
capable of withstanding the weight of the machine.
The machine should always be securely fastened to the
workbench with appropriate fixings.
• Where possible, floor standing machines should always
be secured to the floor with fixings appropriate to the
structure of the floor.
• The floor surface should be sound and level. All of the
feet of the machine should make contact with the floor
surface. If they do not, either re-locate the machine to
a more suitable position or use packing shims between

5
2. General Health & Safety Guidance
the feet and the floor surface to ensure the machine is
stable.
7. Remove adjusting keys and wrenches
• Ensure that all adjusting wrenches and keys are
removed before switching the machine ‘ON’. There
is a risk of severe personal injury or damage to the
machine from airborne objects.
8. Before switching the machine ‘ON’
• Clear the machine table of all objects (tools, scrap
pieces etc.)
• Make sure there is no debris between the work piece
and the table / work support.
• Ensure that the work piece is not pressed against, or
touching the saw blade or cutting tool.
• Check all clamps, work holding devices and fences to
ensure that they are secure and cannot move during
machining operations.
• Plan the way that you will hold and feed the work
piece for the entire machining operation.
9. Whilst machining
• Before starting work, watch the machine while it runs.
If it makes an unfamiliar noise or vibrates excessively,
switch the machine ‘OFF’ immediately and disconnect
it from the power supply. Do not restart until finding
and correcting the source of the problem.
10. Keep the work area clear
• Working clearances can be thought of as the distances
between machines and obstacles that allow safe
operation of every machine without limitation.
Consider existing and anticipated machine needs, size
of material to be processed through each machine
and space for auxiliary stands and/or work tables.
Also consider the relative position of each machine to
one another for efficient material handling. Be sure to
allow yourself sufficient room to safely operate your
machines in any foreseeable operation.
• Cluttered work areas and benches create the risk of
accidents. Keep benches clear and tidy away tools that
are not in use.
• Ensure that the floor area is kept clean and clear of any
dust and debris that may create trip or slip hazards.
11. Consider the work area environment
• Do not expose the machine to rain or damp conditions.
• Keep the work area well lit and ensure that there is
artificial lighting available when there is insufficient
natural light to effectively light the work area. Lighting
should be bright enough to eliminate shadow and
prevent eye strain.
• Do not use the machine in explosive environments e.g.
in the presence of flammable liquids, gases or dust.
• The presence of high levels of dust created by
machining wood can present a risk of fire or explosion.
Always use dust extraction equipment to minimise the
risk.
12. Keep other persons away (and pets)
• The machine is designed to be used by one person
only.
• Do not let persons, especially children, touch the
machine or extension cable (if used) and keep visitors
away from the work area.
• Never leave the machine running unattended. Turn
the power supply off and do not leave the machine
unattended until it comes to a complete stop.
• If the work area is to be left unattended, all machinery
should be switched ‘OFF’ and isolated from the mains
power supply.
13. Store machines safely when not in use
• When not in use, machines should be stored in a dry
place, out of reach of children. Do not allow persons
unfamiliar with these instructions or with the machine
to operate it.
14. Do not overreach
• Choose a working position that allows your body to
remain balanced and feed the work piece in to the
machine without overreaching.
• Keep proper footing and balance at all times.
15. Electrical supply
• Electrical circuits should be dedicated to each machine
or large enough to handle combined motor amp loads.
Power outlets should be located near each machine
so that power or extension cables are not obstructing
high-traffic areas. Observe local electrical guidelines
for proper installation of new lighting, power outlets,
or circuits.
• The machine must be connected to an earthed power
supply.
• The power supply must be equipped with a circuit
breaker that provides short circuit, overload and earth
leakage protection.
• The voltage of the machine must correspond to the
voltage of the mains power supply.
• The mains plug fitted to the machine should always
match the power outlet. Do not modify the plug in
any way. If a replacement plug is required it should be
fitted by a competent person and of the correct type
and rating for the machine.
• If you are unsure about any electrical connections
always consult a qualified electrician.

6
2. General Health & Safety Guidance
16. Avoid unintentional starting of the machine
• Most machines are fitted with a no-volt release (NVR)
switch to prevent unintentional starting. If in doubt
always ensure the machine switch is in the ‘OFF’
position before connecting it to the power supply. This
means the machine will not automatically start up
after a power cut or switching on of the power supply,
unless you first reset the start switch.
17. Outdoor use
• Your machine should not be used outdoors.
18. Extension cables
• Whenever possible, the use of extension cables is
not recommended. If the use of an extension cable is
unavoidable, then it should have a minimum core cross
section of 2.5mm² and limited to a maximum length of
3 metres.
• Extension cables should be routed away from the
direct working area to prevent a trip hazard.
19. Guard against electric shock
• Avoid body contact with earthed or grounded surfaces
such as pipes and radiators. There is an increased risk
of electric shock if your body is earthed or grounded.
20. Always work within the machine’s intended
capacities
• Operator safety and machine performance are
seriously adversely affected if attempts to make the
machine perform beyond its limits are made.
21. Do not abuse the power cable
• Never pull the power cable to disconnect it from the
power socket. Always use the plug.
• Keep the power cable away from heat, oil and sharp
edges.
• Do not use the power cable for carrying or moving the
machine.
22. Secure the work piece
• Ensure that the work piece is securely held before
starting to machine it.
• When working within 300 mm of the machining area,
always use a push stick to feed the work piece in to
the blade or cutting tool. The push stick should have a
minimum length of 400 mm. If the push stick becomes
damaged, replace it immediately.
• Use extra supports (roller support stands etc.) for any
work pieces large enough to tip when not held down
to the table top.
• Do not use another person as a substitute for a table
extension, or as additional support for a work piece
that is longer or wider than the basic table, or to help
feed, support, or pull the work piece.
• Do not attempt to machine more than one work piece
at a time.
• When feeding the work piece towards the blade or
cutting tool never position your hands in direct line of
the cutting path. Avoid awkward operations and hand
positions where a sudden slip could cause your hand
or fingers to move into the machining area.
23. Stay alert
• Safety is a combination of operator common sense and
alertness at all times when the machine is being used.
• Use all machines with extreme care and do not use the
machine when you are tired or under the influence of
drugs, alcohol or medication.
24. Use the correct tool for the job
• Do not use the machine for any purpose other than
which it was designed.
• When selecting replacement cutting tools and blades,
always ensure that they are designed to cut the
material that you intend to use them for. If in any
doubt seek further advice from the manufacturer.
25. Connect dust extraction equipment
• Always use dust extraction equipment. The dust
extractor should be of suitable size and capacity
for the machine that it is connected to and have a
filtration level appropriate to the type of waste being
collected. Refer to the relevant section of the manual
for details of the specific dust extraction requirements
for this machine.
• The dust extractor should be switched ‘ON’ before
starting the machine that it is connected to. The dust
extractor should be left running for 30 seconds after
the last machining operation is complete in order to
clear any residual waste from the machine.
26. Ensure that the machine is correctly guarded
• Never use the machine if any of the standard safety
guards and equipment are removed or damaged.
• Some machines incorporate safety interlocks to
prevent the machine from being used without the
guards in place. Never attempt to bypass or modify the
interlocks to allow the machine to be used without the
guards in place.
27. Maintain your machine with care
• This manual gives clear instructions on installation, set
up and operation of the machine and also details any
routine and preventative maintenance that should be
performed periodically by the user.
• Remember always to switch off and unplug the
machine from the power supply before carrying out
any setting up or maintenance operations.
• Follow any instructions for the maintenance of

7
accessories and consumables.
• Do not use compressed air to clean the machine.
Always use a brush to dislodge dust in places that are
awkward to reach and a dust extractor to collect the
waste.
• Inspect electric cables periodically and, if damaged,
have them replaced by an authorised service facility or
qualified electrician.
• Inspect extension cables (if used) periodically and
replace if damaged.
28. Keep cutting tools sharp and clean
• Correctly maintained cutting tools are easier to control
and less likely to bind.
• Cutting tools and blades can become hot during use.
Take extreme care when handling them and always
allow them to cool before changing, adjusting or
sharpening them.
29. Disconnect the machine from the power
supply
• When not in use, before servicing, changing blades etc.
always disconnect the machine from the power supply.
30. Check for damaged parts
• Before each use of the machine, it should be carefully
checked to determine that it will operate properly and
perform its intended function.
• Check for alignment of moving parts, binding of
moving parts, breakage of parts and any other
conditions that may affect the operation of
the machine.
• A guard or other part that is damaged should be
properly repaired or replaced by a qualified person
unless otherwise indicated in this instruction manual.
• Do not use the machine if the switch does not turn the
machine ‘ON’ and ‘OFF’.
• Have defective switches replaced by a qualified person.
31. Warning!
• The use of any accessory or attachment, other than
those recommended in this instruction manual, or
recommended by our Company may present a risk
of personal injury or damage to the machine and
invalidation of the warranty.
32. Have your machine repaired by a qualified
person
• This machine complies with the relevant safety rules
and standards appropriate to its type when used in
accordance with these instructions and with all of
the standard safety guards and equipment in place.
Only qualified persons using original spare parts
should carry out repairs. Failure to do this may result
in considerable danger to the user and invalidation of
warranty.
33. Caution! Motor may become hot during use
• It is normal for motors on some machines to become
hot to the touch during use. Avoid touching the motor
directly when in use.
2. General Health & Safety Guidance

8
3. Additional Health & Safety Guidance for
Woodturning Lathes
Safe Operation
Familiarise yourself with the machine
• Machining operations using wood turning lathes have
a history of serious accidents. Most serious accidents
resulted from the work piece being thrown from the
lathe whilst turning. Other accidents can be caused
by loose clothing being drawn in to the rotating work
piece or hands becoming trapped between the rotating
work piece and fixed parts of the lathe.
2. Before switching the machine ‘ON’
• Before attaching a work piece to a faceplate, always
prepare it to be as round as possible. This will minimise
vibration whilst turning. For further instructions please
see the section of this manual entitled Intended Use
of the Lathe & Basic Woodturning Instructions.
• Adjust the tool rest to the correct height and distance
from the work piece and check that all fixings are
secure.
• Check that the size of the work piece is within the
safe working capacities of the lathe as detailed in the
manual.
• Select the correct speed according to the size and type
of work piece.
The slowest speed is the safest speed to start any new
work piece.
• Always rotate the work piece by hand before starting
the lathe to ensure it does not come into contact with
the tool rest. If the work piece strikes the tool rest
during operation, it could be split and thrown from the
lathe.
• When using a faceplate always ensure the work piece
is well secured with screws of a suitable diameter and
length.
• Remove any loose knots and bark from the work piece
before mounting it to the lathe.
• If mounting a work piece between centres, always
ensure that the tailstock is correctly adjusted and fully
secure. Check that the locking handle for the tailstock
barrel is fully tightened.
3. Whilst using the lathe
• Do not allow the turning tool to dig in to the work
piece, which could result in the work piece splitting
or being thrown from the lathe. Always position
the tool rest at the correct height. For further
instructions please see the section of this manual
entitled Intended Use of the Lathe & Basic
Woodturning Instructions.
• Before starting to machine a work piece that is off
centre or not perfectly round, always set the machine
to the slowest speed and gradually increase speed as
the work piece becomes more balanced as material is
removed. Running the lathe too fast could cause the
work piece to be thrown from the lathe or the turning
tool to be snatched from your hands.
• Always store turning tools in a safe place away
from the work area of the lathe. Never reach over
the rotating work piece to reach for turning tools or
accessories.
• Never attempt to adjust the position of the tool rest
whilst the machine is running. Always switch the
machine ‘OFF’ and wait until the work piece has
stopped rotating before attempting any adjustments.
• Do not mount a work piece that contains excessive
splits or loose knots or bark.
• Keep firm hold and control of the turning tool at all
times. Use extreme caution when knots and voids are
exposed in the work piece.
• Finish all hand sanding before removing the work
piece from the lathe. Do not exceed the speed
used for the last cutting operation. For further
instructions please see the section of this manual
entitled Intended Use of the Lathe & Basic
Woodturning Instructions.
• Do not attempt to remount a work piece that has
been turned on a faceplate unless you are deliberately
turning eccentric work. You cannot remount faceplate
turned work and expect it to run true, as the timber
will have expanded or contracted.
• Do not remount a work piece that has been turned
between centres if the original centres have been
altered or removed, unless you are deliberately turning
eccentric work.
• If re-mounting any work piece, always set the machine
to the slowest speed and gradually increase the speed
as the work piece becomes more balanced as material
is removed.
• Use extra caution when mounting a work piece that
has been turned between centres to a faceplate, or
when mounting a faceplate turning between centres,
for subsequent machining operations. Always ensure
that the lathe is set to the slowest speed before
switching ON.
• Do not attempt to perform any machining operations
when holding the work piece by hand.
• Do not mount a reamer, milling cutter, wire wheel,
buffing wheel, drill bit or any other tool to the

9
3. Additional Health & Safety Guidance for
Woodturning Lathes
headstock spindle.
• Always ensure that the turning tool is in contact with
the tool rest and fully supported before applying the
tool to the work piece.
• When the tool rest base unit is not in use (e.g.
when sanding), it should be moved away from the
headstock, and the tool rest removed.
4. Maintenance
• Before attempting any maintenance and particularly
when cleaning the machine, always remove any
accessories and tooling from the machine.
• Always ensure that any accessories used on the lathe
are kept clean and free from rust and deposits of resin.
• Keep all turning tools sharp and in good condition.
Check that the handles are secure and not split or
damaged.
5. This machine falls under the scope of the ‘Health &
Safety at Work etc. Act 1974’, and the ‘Provision &
Use of Work Equipment Regulations 1998’. In addition
the elimination or control of risks from wood dust is
included in the above regulations and the ‘Control of
Substances Hazardous to Health (COSHH) Regulations
2002’. We recommend that you study and follow these
regulations.
Further guidance is available from The Health & Safety
Executive and their website www.hse.gov.uk and from
the authorised distributor in your country (details on
back cover of the manual).

10
4. Record Power Guarantee
“Products” means the Products sold by Record Power
subject to these terms and conditions;
“Record Power” is Record Power Limited, whose
company registration number is 4804158 and registered
office address is Centenary House, 11 Midland Way,
Barlborough Links, Chesterfield,
Derbyshire, S43 4XA and sells through a network of
Authorised Dealers;
“Authorised Distributor” is the nominated importer
for your region who will generally sell through a network
of Authorised Dealers. Details of Authorised Distributors
for specific countries can be found in the Product manual
or at www.recordpower.info;
“Authorised Dealer” is a retailer or business
authorised to sell Record Power Products to end users.
1 Guarantee
1.1 Record Power guarantees that for a period of 5
years from the date of purchase the components of
qualifying Products (see clauses 1.2.1 to 1.2.9) will
be free from defects caused by faulty construction
or manufacture.
1.2 During this period Record Power, its Authorised
Distributor or Authorised Dealer will repair or
replace free of charge any parts which are proved
to be faulty in accordance with paragraphs 1.1
above provided that:
1.2.1 you follow the claims procedure set out in clause 2
below;
1.2.2 Record Power, our Authorised Distributor or
Authorised Dealer are given a reasonable
opportunity after receiving notice of the claim to
examine the Product;
1.2.3 if asked to do so by Record Power, its Authorised
Distributor or Authorised Dealer, you return the
Product, at your own cost, to Record Power’s
premises or other approved premises such as
those of the Authorised Distributor or supplying
Authorised Dealer, for the examination to take
place;
1.2.4 the fault in question is not caused by industrial
use, accidental damage, fair wear and tear, wilful
damage, neglect, incorrect electrical connection,
abnormal working conditions, failure to follow our
instructions, misuse, or alteration or repair of the
Product without our approval;
1.2.5 the Product has been used in a domestic
environment only;
1.2.6 the fault does not relate to consumable Products
such as blades, bearings, drive belts or other
wearing parts which can reasonably be expected
to wear at different rates depending on usage
(for full details contact Record Power or your local
Authorised Distributor);
1.2.7 the Product has not been used for hire purposes, by
you or by a previous owner;
1.2.8 the Product has been purchased by you as the
guarantee is not transferable from a private sale.
1.2.9 where the Product has been purchased from a
retailer, the 5 year guarantee is transferable and
begins on the date of the first purchase of the
Product and in the event of a claim under this
guarantee proof of the original purchase date will
be required to validate the warranty period.
2 Claims Procedure
2.1 In the first instance please contact the Authorised
Dealer who supplied the Product to you. In our
experience many initial problems with machines
that are thought to be due to faulty parts are
actually solved by correct setting up or adjustment
of the machines. A good Authorised Dealer should
be able to resolve the majority of these issues
much more quickly than processing a claim under
the guarantee.
2.2 Any damage to the Product resulting in a potential
claim under the guarantee must be reported to the
Authorised Dealer from which it was purchased
within 48 hours of receipt.
2.3 If the Authorised Dealer who supplied the Product
to you has been unable to satisfy your query,
any claim made under this Guarantee should be
made directly to Record Power or its Authorised
Distributor (for details of the Authorised Distributor
in your country please see your Product manual
or check www.recordpower.info for details). The
claim itself should be made in a letter setting out
the date and place of purchase, and giving a brief
explanation of the problem which has led to the
claim. This letter should then be sent with proof of
the purchase date (preferably a receipt) to Record
Power or its Authorised Distributor. If you include
a phone number or email address this will help to
speed up your claim.
2.4 Please note that it is essential that the letter of
claim reaches Record Power or its Authorised
Distributor on the last day of this Guarantee at the
latest. Late claims will not be considered.
3 Limitation of Liability
3.1 We only supply Products for domestic and private
use. You agree not to use the Product for any
commercial, business or re-sale purposes and we

11
4. Record Power Guarantee
have no liability to you for any loss of profit, loss of
business, business interruption or loss of business
opportunity.
3.2 This Guarantee does not confer any rights other
than those expressly set out above and does not
cover any claims for consequential loss or damage.
This Guarantee is offered as an extra benefit and
does not affect your statutory rights as a consumer.
4 Notice
This Guarantee applies to all Products purchased
from an Authorised Dealer of Record Power
within the United Kingdom of Great Britain
and Northern Ireland. Terms of Guarantee may
vary in other countries – please check with the
Authorised Distributor in your country (details of
the Authorised Distributor for your country can be
found in the manual or at www.recordpower.info).

12
5. Using the Chuck Safely
1. The machine should be disconnected from the
mains power supply when fitting or removing the
chuck.
2. Do not run the machine with the chuck mounted
unless the workpiece is in position, otherwise the
component parts may become dangerously loose.
3. Before starting the machine ensure that the
workpiece is firmly secured by the chuck, that there
are no loose components in the chuck and that
the chuck is firmly secured to the machine spindle
nose.
4. Turn the workpiece by hand to ensure that nothing
obstructs its rotation, check that all other parts of
the machine (especially the tool rest) are firmly
clamped.
5. Stand clear of the line of rotation when starting
and when first applying the tool. If in doubt about
whether it is safe to proceed - stop the machine
and check the workpiece to see if it is still secure.
6. The Chuck should never be run in reverse or it
could become dangerously loose.
7. Larger workpieces should be run on the slowest
speed until the operator is sufficiently experienced
to increase the speed safely.
8. When turning be careful not to touch any part of
the chuck particularly in the vicinity of the spaces
between the jaws.
9. Do not sand a spiral shaped workpiece when
the machine is running. This is a very dangerous
practice as the spiral acts as a fast feed mechanism
directing anything in the spiral along its length.
10. When turning heavy, out of balance timber, security
of the mounting is most important. However, since
each piece of timber is unique it is difficult to lay
down precise rules. It is advised that the newcomer
to large diameter turning should gain experience
with smaller work to start with - gradually working
up to the maximum size that they are interested in.
Make frequent checks on the security of the timber,
gaining a knowledge of what is adequate and
what is not for the particular type of work being
done.

13
6. Intended Use of the Lathe
The lathe is designed for turning wood between centres
or on the headstock (using appropriate accessories), for
sanding and applying finishes to wood. It is not to be
used for any other purpose. Doing so may invalidate its
warranty and may cause serious harm to the user.
Health & Safety
Please read the health and safety instructions contained
in this manual and the specific health and safety
instructions relating to woodturning. In addition, it is
recommended to ensure your work area is adequately
equipped with dust extraction and air filtration
equipment.
Respiratory equipment should also be used to greatly
reduce lung exposure to harmful fine dust. Always
establish the properties of the timber being turned and
take extra care when working with harmful and
carcinogenic materials.
Eye protection must always be worn. Due to the nature of
woodturning, shavings, dust and splinters can be thrown
at fast speeds, making adequate eye protection essential.
Mounting Timber to a Faceplate or Chuck
When mounting the workpiece to a faceplate or chuck,
it is advisable to shape the timber into as cylindrical
a profile as possible, see fig 6.1. Turning unbalanced
timber increases lathe vibration, the risk of it being
thrown from the lathe, increased risk of chisel dig in and
makes correct positioning of the tool rest difficult due to
variable distances.
Mounting Timber Between Centres
When turning between centres, it is essential to correctly
and securely mount the timber so as to reduce the risk
of it being thrown from the lathe. It is also essential to
mount the timber as centrally as possible. This will reduce
the amount of roughing out needed and also maximise
the possible diameter of the final piece.
1. Using a square or rectangular profile blank, draw two
lines, one from each opposing diagonal corner to the
other, at each end of the blank. The point where the lines
intersect indicates the centre of the blank. See fig 6.2.
If using irregular shaped timber, a centre finder is an
invaluable tool.
Fig 6.1
Fig 6.2
i
Kg
i
Kg

14
6. Intended Use of the Lathe
Fig 6.3
Fig 6.4
Fig 6.5
2. Take the drive centre supplied with the lathe and place
its point directly on to the centre point of one end of the
blank. Using a soft mallet (of either plastic, rubber or
wood) tap the drive centre with reasonable force until it
bites into the timber. See fig 6.3.
3. Carefully place the drive centre into the headstock
spindle of the lathe, fig 6.4, and ensure that it is correctly
seated in the spindle by tapping it firmly into place with
a mallet.
4. Slide the tailstock up the bed until the tailstock centre
is almost touching the other end of the blank. Lock the
tailstock in position and use the hand wheel to extend
the tailstock centre until it grips the blank firmly at
the centre point. See fig 6.5. Then use the tailstock
locking handle the secure the position. The blank is now
successfully mounted and ready to be turned.
Positioning the Tool Rest
It is extremely important to ensure the tool rest is
correctly positioned before turning on the lathe. Place the
tool rest close to the timber, allowing enough room to
manoeuvre the chisel with ease. Spin the timber by hand
to ensure it does not come into contact with the tool
rest. If the lathe is started without checking this and the
timber hits the tool rest, there is a risk the timber could
be thrown from the lathe and cause injury. Never attempt
to reposition the tool rest while the lathe is in motion.
Tool rest height is also important and varies depending
on the chisel being used. When using a roughing gouge,
the cutting edge should come into contact with the
centre of the workpiece, see fig 6.6.
Fig 6.6

15
6. Intended Use of the Lathe
Fig 6.8
Fig 6.10
Fig 6.7
Fig 6.9
If using a skew chisel, the cutting edge should be applied
approximately 3/8" (10 mm) above the centre height, see
fig 6.7. A spindle gouge's cutting edge should come into
contact with the workpiece approximately 3/8" (10 mm)
below its centre, see fig 6.8.
Using the Roughing Gouge
The first step when turning between centres is invariably
to 'rough out' the blank. This involves taking a square
section blank and paring it down with a roughing gouge
to a cylindrical profile, ready to shape into the final piece.
Roughing gouges are usually sharpened to have the bevel
at a 45º angle. Using the tool rest to support the blade,
offer the blade to the workpiece at an angle, see fig 6.9.
When offering the roughing gouge to the workpiece, the
bevel should be rubbing it, without cutting. To make a
cut, gently raise the handle of the tool in order to bring
the cutting edge into contact with the timber. Using light
passes, move the blade outwards towards the same edge
of the timber which the blade is facing, fig 6.9. Never
move the tool backwards, as this introduces the risk of
splintering the wood and causing injury.
Using the Spindle Gouge
A spindle gouge is used to shape the final profile of a
spindle and is capable of finer work than a roughing
gouge. It is designed specifically for cutting coves or
valleys. The blade should come into contact with the
wood at just below the centre line. Resting it on the tool
rest, apply the blade to the workpiece at an angle, see
fig 6.10, rubbing the bevel onto it. Raise the handle
to apply the cutting edge and make cuts. As with the
roughing gouge, use controlled and light passes, trying
to not remove too much wood at once. Never attempt to
use a spindle gouge for working on bowls or hollow form
work as the angle of the cutting bevel of the gouge is
too shallow and will cause it dig in to the work piece or
snatch the tools from your hands.

16
Speeds of the Lathe
To ensure the safest possible use of the lathe, it is
important to understand which speeds are suited to
which tasks. In general, the slower speeds should be used
for the initial turning and roughing out of large pieces
and the slowest speed should be used when large pieces
are out of balance. This will reduce the possibility of the
workpiece being thrown from the lathe.
Medium speeds are ideally suited for general purpose
work which doesn't place heavy loads on the spindle
of the lathes, for example when creating the profiles of
spindles and some smaller bowl turning.
The fastest speeds should be used only for small diameter
work, where the size of workpiece is relatively small and
therefore poses a lower risk of causing damage. Extra
care should be taken when turning at the fastest speeds,
using only a relatively light touch.
When sanding, care should be taken to not burn the
operator's hands or the workpiece. It is recommended to
not exceed the speed used for the last turning operation.
If in doubt, use a slow speed.
i
Kg
Fig 6.11
Using the Skew Chisel
Skew chisels are available in both flat and oval profiles.
The curved profile is favoured by many as it gives better
results more easily. Skew chisels are ideal for creating
beads, refining the profiles and can be used to create
a final smooth finish to the workpiece. The skew chisel
should be applied to the workpiece horizontally with the
blade resting on the tool rest, fig 6.11, again with the
bevel rubbing the workpiece and raising the handle to
take careful, controlled cuts.
Further Operations
The guidelines above give basic instructions on some of
the most common woodturning procedures. There are a
wide variety of specialised chisels and many complementary
accessories available for Record Power lathes which
enable a huge variety of work to be created. For further
instructions on more advanced safe and effective
woodturning, please seek professional training.
6. Intended Use of the Lathe

17
1 SC1 2” Mini Chuck
2 62303 40 mm Standard Jaws
3 62831 Deep Wood Screw
4 M5 x 11 countersunk head hex socket screws x 8
5 Protective leather disc
6 M6 x 6 blind set screw
7 60219 Chuck Key
8 3 mm hex wrench
2
3
6
457
8
SC1 2” Mini Chuck Package
7. Contents of the Packages
1

18
1 SC2 2 ½” Mini Chuck
2 62303 40 mm Standard Jaws
3 62831 Deep Wood Screw
4 M5 x 11 countersunk head hex socket screws x 8
5 Protective leather disc
6 M6 x 6 blind set screw
7 60216 Chuck Key
8 3 mm hex wrench
58
7
7. Contents of the Packages
SC2 2 ½” Mini Chuck Package
1
2
3
6
4

19
7. Contents of the Packages
62112 Thread Adaptor M20 x 2 RH
62113 Thread Adaptor M20 x 1.5 RH
62115 Thread Adaptor 7/8”x 12 TPI UN LH
62125 Thread Adaptor RH M33 x 3.5 ISO
62126 Thread Adaptor 3/4” Plain Bore
62127 Thread Adaptor 1-1/8” x 8 TPI UNC RH
62128 Thread Adaptor 3/4” x 16 TPI UNF RH
62129 Thread Adaptor 1” x 10 TPI BSF RH
62130 Thread Adaptor RH M30 x 3.5 RH
62131 Thread Adaptor 1” x 12 TPI UNF RH
62132 Thread Adaptor 1-1/4” x 8 TPI UNS-RH
62133 Thread Adaptor 1” x 8 TPI UNC RH
62134 Thread Adaptor 5/8” Plain Bore
62135 Thread Adaptor 3/4” x 16 TPI BSW RH
62136 Thread Adaptor 3/4” x 10 TPI BSW RH
62137 Thread Adaptor M24 x 3 RH
62152 Thread Adaptor M18 x 2.5 RH
62157 Thread Adaptor Blank. Can be bored up to 30 mm
62159 Thread Adaptor 1” x 8 TPI LH & RH Dual Threaded
62160 Thread Adaptor 7/8”x14 TPI RH
62161 Thread Adaptor M25 x 2 RH
62162 Thread Adaptor 1-1/4” x 8 TPI UNS RH
1 Chuck insert
2 Protective leather disc*
3 M6 x 6 mm blind set screw*
*The blind set screw and protective disc are only supplied with inserts of the following thread sizes:
62125 Thread Adaptor RH M33 x 3.5 ISO
62126 Thread Adaptor 3/4" Plain Bore
62132 Thread Adaptor 1-1/4"x8 TPI UNS-RH for DVR-XP & 1624-44 Lathes
62133 Thread Adaptor 1” x 8 TPI UNC RH
62134 Thread Adaptor 5/8" Plain Bore
Chuck Insert for use with the SC1 2” Mini Chuck
(Sold Separately)
The chuck inserts are available in the following thread sizes:
1 2* 3*

20
8. Operation
Fig 8.1
Fig 8.3
Fig 8.4
The SC1 and SC2 chucks are supplied with a protective
oil coating to all components to inhibit rust. Remove this
oil using white spirit or a similar de-greasing product
before use.
SC2
The SC2 chuck features an M33 x 3.5 thread to its rear.
This means the chuck can be threaded directly onto the
lathe spindle as shown in Fig 8.1, ensuring the chuck is
threaded far enough onto the spindle to allow its back
face to meet the face of the shoulder on the spindle nose.
Before fitting the chuck to the lathe, ensure the threads
match.
The direct thread M33 x 3.5 can be used on a lathe
capable of reverse turning as it features a tapped hole in
the chuck body which allow it to be secured by a blind
set screw to the lathe spindle. If the lathe is to be used
in reverse, the chuck must be secured to the spindle to
prevent it from coming loose during operation. When
the chuck is fully threaded onto the lathe spindle, place
the protective leather pad in the hole on the side of the
chuck, thread in the M6 x 6 blind set screw and tighten,
Fig 8.2.
SC1
The rear of the chuck body features an M40 x 2 pitch
thread to accept the chuck insert.
Ensure the threads of the chuck body and insert are clean
and free from any dust or debris then carefully thread the
insert into the rear of the chuck, Fig 8.3, until the collar
of the insert is touching the chuck body and tighten.
The optional 62825 Universal Wrench is ideal for this
purpose Fig 8.4.
The blind set screw supplied with the chuck must now
be used to secure the insert to the chuck body. In normal
use the chuck insert will be further tightened into the
chuck body due to the direction of the spindle’s rotation.
However, if the lathe will be used in reverse, the blind set
screw ensures the insert will not come loose.
Fig 8.2
Blind set screw hole
Chuck insert