RED DEVIL XVL10 User manual

www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-852-1811
Owner’s Manual:
XVL10
One-Gallon Vortex Mixer

2www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-852-1811
Owner’s Manual: XVL10
1785871 Rev J
ECO 15-0051 B
December 2015
Table of ConTenTs
1. Safety Information 3
1.1 Safety Precaution Labels 4
1.2 Safety Precaution Summary 5
2. Introduction 6
2.1 Application 6
2.2 Specifications 6
3. Unpacking & Install 7
4. Operation 8
4.1 Control Panel 8
4.2 Install a Container 9
5. Cleaning 9
6. Troubleshooting 10
7. Wiring Diagram 11
8. Exploded Views 12
8.1 Frame Assembly 12
8.2 Enclosure Assembly 13
8.3 Drive Assembly 14
8.4 Rotating Assembly 15
9. Ordering 16
Replacement Parts 16
10. Warranty 17
Notes 18

3
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-852-1811
1785871 Rev J
ECO 15-0051 B
December 2015
Owner’s Manual: XVL10
Safety Information, continued...
Review this owner’s manual and read all warning labels on the machine prior to use.
The three main safety notifications used in this manual and on the warning labels are WARNING,
CAUTION and NOTICE. They have specific meanings and indicate the potential dangers from misuse of
the machine.
“WARNING!” indicates a hazardous situation, which, if not avoided,
could result in death or serious injury. These serious injuries could
include permanent loss of function or significant disfigurement,
disability, considerable pain and suffering, amputations, severe
burns, and loss or impairment of vision or hearing. Take all necessary
precautions to avoid unnecessary injury.
“CAUTION!” indicates a hazardous situation, which, if not avoided,
could result in minor or moderate injury.
“NOTICE” indicates practices that do not involve physical injury but
may damage the machine.
1. safeTy InformaTIon
NOTICE

4www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-852-1811
Owner’s Manual: XVL10
1785871 Rev J
ECO 15-0051 B
December 2015
-This machine is not explosion proof rated.
-Review product label, Material Safety Data Sheet, and HMIS rating of
materials and exposures prior to mixing to determine potential hazards.
-Use in dry and well-ventilated environment where dust and ammable
vapors are not present; risk of physical injury exists if used in hazardous
environment.
-All containers must be properly sealed and void of leaks.
-Esta máquina no tiene la clasicación de prueba de explosión.
- Revise la etiqueta del producto, la hoja informativa de datos de seguridad,
su clasicación HMIS antes de mezclar y exposiciones de materiales
peligrosos para determinar los peligros potenciales.
-Use en un ambiente seco y bien ventilado donde polvo y vapores
inamables no estén presentes; Riesgo de daño sico existe si es utilizado
en un ambiente peligrosos.
-Todos los contenedores deben estar bien sellados y sin fugas.
-Cette machine n'est pas classé antidéagrant.
-Examen e’tiquette du produit, Fiche de dane’es de se’curite’, Et mate’riel
HMIS cote et expositions , avant de faire le me’lange pour de’terminer les
risques potentiels.
-Utilisation a’sec et bien ae’re’environnement ou’la poussie’re et les
vapeurs inammables ne sont pas presents; risque de blessure physique
existe si utilise’en environnement dangereux.
-Tous les conteneurs doivent être convenablement scellés pour éviter les
fuites
WARNING
-Machine must be properly grounded before use; improper ground-
ing could cause electric shock and injury.
-Disconnect power cord before servicing, cleaning, or removing any
covers, and follow lockout/tagout procedures in owner’s manual;
failure to disconnect power could cause electric shock and injury.
-Review Owner’s Manual before installing or operating.
-La maquinaria debe ser apoyada correctamente en el suelo antes
de usar, el no apoyarla puede causar choque eléctrico y daños.
-Desconecte la energía antes de dar mantenimiento, limpiar o quitar
cualquier cubierta, y siga los procedimientos de
bloqueo/etiquetado del manual, Fallar en desconectar puede causar
choque eléctrico y daños.
-Revise el manual del usuario antes de instalar u operar.
-La machine doit e’tre correctement mis a’ la terre avant de les
utilizer mise a’ la terre incorrecte peut provoquer un choc e’lectrique
et de blessure.
-De’branchez le cordon d’alimentation avant de proce’der a’
l’entretien, le nettoyage ou le retrait des capots; suivez la proce’dure
d’isolation/consignation proce’dures dans le manuel de l’opre’rateur;
E’chec de de’brancher la source d’alimentation peut provoquer
shockand e’lectrique blessures.
-Re’examiner le fonctionnement manuel avant l’installation.
WARNING
Safety Information, continued...
...Safety Information, continued
-Do not open door until machine comes to a complete stop;
moving parts inside could cause serious injury.
-No abra la puerta hasta que la marquina se detenga
completamente, las partes internas en movimiento pueden
causar heridas graves.
-Ne pas ouvrezla porte jusqu’a’ ce que la machine est
comple’tement arre’te’; pièces en mouvement à l'intérieur
pourrait provoquer des blessures graves.
PARTES EN MOVIMIENTO
PIE’CES EN MOUVEMENT
MOVING PARTS INSIDE
1.1 Safety Precaution Labels
Part No. 1780899 Part No. 1781570
Part No. 1784963

5
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-852-1811
1785871 Rev J
ECO 15-0051 B
December 2015
Owner’s Manual: XVL10
1.2 Safety Precaution Summary
...Safety Information, continued
WARNING!
DO NOT attempt to replace any damaged
electrical wire or components. Improper
replacement could result in electric shock and
serious injury. Only a qualified service
representative should attempt to repair or
replace any damaged electrical components.
Review this owner's manual before installing
or operating.
The machine must be properly grounded
prior to use. In the case of an electrical short
circuit, grounding reduces the risk of electric
shock by providing an escape wire for the
electric current.
The machine’s power cord has a grounding
wire with an appropriate grounding plug. This
plug must be inserted into an electrical outlet
that is properly installed and grounded
according to all local codes and ordinances.
If you must repair or replace the power cord
or plug, do not connect the grounding wire to
either flat-blade terminal. The wire with
insulation having an outer surface that is green
(with or without yellow stripes) is the grounding
wire.
Check with a qualified electrician if you don’t
completely understand these grounding
instructions, or if you are not sure whether the
machine is properly grounded. Do not modify
the plug provided; if it won’t fit in the outlet,
have a proper outlet installed by a qualified
electrician.
Disconnect the power cord before servicing,
cleaning, or removing any covers
Follow the lockout/tagout procedures of your
company.
CAUTION!
Keep the work area free of clutter and
electrical cords.
Avoid extension cords. To minimize the risk
of improper electrical grounding, extension
cords are not recommended. If an extension
cord is unavoidable, consult a qualified
electrician to determine what type of extension
cord will satisfy the grounding, current capacity,
and other requirements of the particular
situation.
Use the proper power source. Refer to the
machine data plate on the right side panel or
the section 2.1, Specifications, in this manual.
Keep customers away from the work area.
The machine should be used only by properly
trained individuals.
DO NOT open the door until the machine
comes to a complete stop.
To avoid electric shock, don’t get the timer,
control panel, or wiring wet.
This machine is not explosion proof.
All containers must be properly sealed and void
of leaks.
Review product label, Material Safety Data
Sheet, and HMIS rating of materials prior to
mixing to determine potential hazards.
DO NOT use solvent-based cleaners or
thinners.
Use in a dry and well-ventilated environment
where dust and flammable vapors are not
present.
Product safety labels should be inspected
and cleaned periodically to maintain good
legibility. Replace any labels that are no
longer legible.

6www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-852-1811
Owner’s Manual: XVL10
1785871 Rev J
ECO 15-0051 B
December 2015
2. InTroduCTIon
2.1 Application 2.2 Specications
Congratulations on your purchase of the X V L10
one-gallon vortex mixer . This machine is
designed to accommodate standard plastic or
metal 1-gallon paint cans. When used with the
9783761 Adapter, it also accommodates quart
and pint cans. Using the 6786133 foam Adapter
with the 9783671 Adapter accomodates half pint
cans.
Understand your machine's features and
proper operation to take full advantage of its
capabilities.
Read this entire manual completely before
operating the machine. Practice installing and
removing a can before mixing for the first time.
Keep this manual for future reference.
Always follow all safety instructions!
Unit Size: W15. in. (38.1 cm) D21.75in. (55.2 cm)
H21 in. (53.3 cm)
Machine Weight: 81 lbs. (36.7 kg)
Electric Service:110 V 60 Hz
Capacity: 15 lb. (6.8 kg)
Sizes Mixed: 1 gal., 1 qt.,
Machines rated at 110 V, 60 Hz are for use with a
nominal 120 V circuit.
20"
15" 21"

7
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-852-1811
1785871 Rev J
ECO 15-0051 B
December 2015
Owner’s Manual: XVL10
3. unpaCkIng & InsTallaTIon
This machine was shipped fully assembled.
Before plugging in the machine or attempting to
operate it:
1. Use a 1/2 in. combination wrench and a 1/2
in. socket wrench to remove the shipping bolts
at the back of the mixer (at the end of the yellow
lanyard). To loosen, turn the bolts counter-
clockwise until the nuts and washers have been
removed from the bottom side of the pallet. It
may be necessary to prop the machine up to get
at the nuts underneath the pallet.
2. Slide the bolts up through the frame and out
of the mixer. Set aside the bolts, washer, nuts,
and yellow lanyard in case they are needed for
future shipment of the mixer.
3. Set the machine on a stable, level surface
and plug it in an appropriately grounded outlet
(see section 1.2, Safety Precaution Summary, for
grounding information).
NOTE: If the machine needs to be shipped any
time, contact Red Devil to obtain the appropriate
packaging kit, part no. 6784975. See section 9,
Ordering, for ordering information.

8www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-852-1811
Owner’s Manual: XVL10
1785871 Rev J
ECO 15-0051 B
December 2015
4. operaTIon
4.1 Control Panel - XVL10
• Operation Indicator (A): This light is
illuminated during machine operation.
• Power Switch (B): Turn the power o or
on.
• Counter (C): View number of machine
cycles.
• Pastels (Two-Minute Cycle) (D): Push to set
a two-minute cycle.
• Deeptones (Three-Minute Cycle) (E): Push
to set a three-minute cycle,
(A)
(B)
(E)
(D)
(C)

9
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-852-1811
1785871 Rev J
ECO 15-0051 B
December 2015
Owner’s Manual: XVL10
1. Open the cabinet Door
2. Load the can into the machine for mixing:
• Gallon Cans: Insert the can into the can
holder. Slip the bail handle into the clip
retainers (D).
• Quart Cans: Place the can inside the quart
adapter, 9783761 (A). Set the quart can
horizontally with the lid up. (See Figure 1)
• Pint Cans: Place round pint cans vertical,
with the lid up. Close the 9783761 adapter
around the can. (See Figure 2)
• Half Pint Cans: Place the half pint can inside
the 6786133 (E) foam adapter. Close the
9783761 adapter arount the 6786133 foam
adapter. (See figure 3)
3. For Quarts, Pints & Half pints: Insert the
adapter into the can holder .Make sure the
9783761 adapter lugs (C) are lined up with the
bail retainers and the adapter is all the way to
the bottom of the can holder (B). (See Figure 4)
4. Close the cabinet door. The mixer has a
safety switch that interrupts operation if the
door is open.
5. Select the desired mix time.
If the container handle wasn’t properly
secured, press the STOP button on the control
panel.
NOTE: If colorant has been added to the paint,
be sure to reattach paint can lid tightly (using
the RED DEVIL EQUIPMENT Lid Press, Part No.
0-5080).
Select mix time by pressing a preset mix cycle
push button (XVL10 models).
Always unplug the power cord before
cleaning! DO NOT get the timer, control panel,
or wiring wet.
CLEANING:
Keeping the machine clean is important for
reliable operation.
• Colorant or base paint spilled on machine
surfaces can be removed using lukewarm
water and mild detergent for water-based/
glycol colorants.
• To preserve the appearance of the machine,
do not use abrasives to clean machine
surfaces.
(B)
5. CleanIng
(A)
(D)
(C)
Figure 1
Figure 3
Figure 2
Figure 4
(E)

10 www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-852-1811
Owner’s Manual: XVL10
1785871 Rev J
ECO 15-0051 B
December 2015
6. TroubleshooTIng
PROBLEM CAUSE REMEDY
Machine won’t run
Not connected to power source Connect to power source
Building circuit breaker or fuse
blown Reset breaker or replace fuse
Machine door does not make
contact with door limit switch
Readjust switch to make contact with
door switch screw when door is closed
Motor thermal protector acti-
vated Allow to cool, then restart
Machine circuit breaker trippedReset by pressing circuit breaker back
in
Faulty Motor Contact Red Devil Equipment Co.
Customer Care
Emergency E-STOP pushbutton
is activated
Turn switch knob 1/4-turn clockwise to
disengage
Faulty controller Contact Red Devil Equipment Co.
Customer Care
Door switch is faulty or needs
adjustment
Adjust the door switch. For replacement,
contact Red Devil Equipment Co.
Customer Care.
Worn, damaged, or loose drive
belt
Unplug power cord, open mixer door,
and visually inspect the drive belt
Excessive Vibration
Pail damaged Fix or replace pail
Can not properly seated Reset can into holder
Feet are not level Adjust and level feet
Machine doesn’t shut off at
end of mixing cycle Faulty controller Contact Red Devil Equipment Co. Customer Care
Machine doesn’t shut off
when door is opened Faulty door limit switch Contact Red Devil Equipment Co. Customer Care
Increasing mechanical noise Bearings worn or damaged Contact Red Devil Equipment Co.
Customer Care
Disconnect the machine from its power source before servicing .

11
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-852-1811
1785871 Rev J
ECO 15-0051 B
December 2015
Owner’s Manual: XVL10
7. WIrIng dIagram
R
BR
B
9780542
ORANGE
WIRE NUT
BL
W
G
POWER CORD
5780485
L
B/W
DOOR
SWITCH
5783815
BL
W
W
B
BR
BL
R
CONTROLLER
5782782
5
6
3
2
1
WIRE COLOR CODE:
BL = BLACK
B = BLUE
B/W = BLACK W/WHITE STRIPE
BR = BROWN
G = GREEN
GR = GREY
R = RED
W = WHITE
5782479
LIGHT
5782448
5782479
9780542
ORANGE
WIRE NUT
9780543
YELLOW WIRE NUT
W
BL
COUNTER
5784008
POWER SWITCH
5782445
9782621
BLUE
WIRE NUT
GR
BR
B
BLUE SWITCH
5782585
(180 SEC)
GREEN SWITCH
5782584
(120 SEC)
9784606
JUNCTION BOX
6784557 CONTROL PANEL ASSEMBLY
5782783
CONTROL HARNESS
W
BL
MOTOR
5785917
BL
W
GG
W
BL
5784216
MOTOR HARNESS
G
BL
GR
BL
BL
G
W
BL
5782484

12 www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-852-1811
Owner’s Manual: XVL10
1785871 Rev J
ECO 15-0051 B
December 2015
8. exploded VIeWs
8.1 Frame Assembly
Exploded Views, continued...
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY
3
5
2
6
1
4
3
5
2
6
1
4
Id Description
1 9780193 Nut, Nylock 3_8-16
2 9780343 Nut 1_4-20 Nylon Lock
3 9780886 SCREW HEX 3_8-16 X 1.00
4 9781929 ISOLATOR, RUBBER - 5300
5 9782044 Foot, Floor Stand
6 9784556 BASE - 1015

13
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-852-1811
1785871 Rev J
ECO 15-0051 B
December 2015
Owner’s Manual: XVL10
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY
...Exploded Views, continued
Exploded Views, continued...
32
25
2
28
15
27
17
31
9
18
21
16
30
7
11
20
26
19
29
33
10
22
6
13
12
8
24
1
3
4
5
23
32
25
2
28
15
27
17
31
9
18
21
16
30
7
11
20
26
19
29
33
10
22
6
13
12
8
24
1
3
4
5
23
ID Description
1 1784562 LABEL, CONTROL PANEL - 1015PB
2 5782445 POWER SWITCH
3 5782448 Operation Lamp, Neon
4 5782584 PUSH BUTTON, GREEN
5 5782585 PUSH BUTTON, BLUE
6 5782782 CONTROLLER, 2 BUTTON TIMER
7 5783815 Switch, Limit 1hp
8 5784008 Counter, cycle
9 9102519 BUSHING,STR.RELIEF
10 9166300 GROMMET
11 9641300 WASHER, FLAT #8 SAE
ID Description
12 9654100 Nut 1_4-20
13 9780164 Washer 1_4 LOCK
15 9780381 Screw Hex #8 X 3_8
16 9780886 SCREW HEX 3_8-16 X 1.00
17 9781338 Screw, Pan Head 8-32 X 1.00
18 9781840 Nut, Keps #8-32
19 9782681 BUMPER, DOOR - 5300
20 9783385 Screw, #10-32 SHWH Tap
21 9783503 LIMIT BRACKET
22 9783510 ACTUATOR LIMIT SWITCH SQ
23 9783672 Plug, .25 Dia Hole
ID Description
24 9784198 Screw, Pan hd thd forming #4 x .38
25 9784222 BOX, CONTROLLER - 5300 PB
26 9784425 Bearing, Bronze Flanged
27 9784426 Sleeve, Steel
28 9784589 SEAL, DOOR - 1015
29 9786423 BOX, DIGITAL DISPLAY - 1015
30 9787239 Enclosure Weldment - 1015
31 9787242 PANEL, CONTROL - XVL10 PB
32 9787240 BACK PANEL 1015
33 9787253 DOOR WELDMENT - 1015
8.2 Enclosure Assembly

14 www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-852-1811
Owner’s Manual: XVL10
1785871 Rev J
ECO 15-0051 B
December 2015
16
8
18
10
7
17
6
3
13
1
14
5
11
9
15
5
4
19
2
16
8
18
12
10
7
17
6
3
13
1
14
5
11
9
15
5
4
19
2
Id Description
1 5785917 MOTOR, 1_4 HP 56C, W_HARNESS
2 6785869 ROTATING ARM ASBY - XVL10
3 6787044 BRG HSNG ASSY XVL 10, 12
4 9760514 Washer 1_4 SAE .281 ID
5 9780343 Nut 1_4-20 Nylon Lock
6 9780402 Washer 3_8 split lock
7 9780886 SCREW HEX 3_8-16 X 1.00
8 9781414 Washer Fender 1_4
9 9781904 WASHER, SPACER
10 9782182 PULLEY, BIG - 1015
Id Description
11 9782537 GEAR, BIG BEVEL, STATIONARY
12 9783838 Retaining Ring, .625 Shaft
13 9781960 Key, Square .187 x 1.00
14 9784523 FRAME, MIX - 1015
15 9784554 SCREW, SOC HD CAP 1_4-20 X 1.25
16 9784555 SCREW, HEX SEMS 1_4-20 X .75
17 9784651 BELT - 1015
18 9784652 PULLEY, SMALL - 1015
19 9785907 SCREW, HEX CAP 1_4-20 X 2.75
8.3 Drive Assembly
...Exploded Views, continued
Exploded Views, continued...
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY

15
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-852-1811
1785871 Rev J
ECO 15-0051 B
December 2015
Owner’s Manual: XVL10
8.4 Rotating Assembly
...Exploded Views, continued
Exploded Views, continued...
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY
4
7
5
6
8
12
10
3
2
8
13
14
1
2
11
9
4
7
5
6
8
12
10
3
2
8
13
14
1
2
11
9
Id Description
1 6785987 CAN HOLDER ASSY, XVL 10
2 9760514 Washer 1_4 SAE .281 ID
3 9780343 Nut 1_4-20 Nylon Lock
4 9781896 CLAMP COLLAR, 0.625 ID
5 9781904 WASHER, SPACER
6 9781960 KEY, SQUARE .1875 x 1.00 LG
7 9782538 GEAR, URETHANE - 5300
8 9784555 SCREW, HEX SEMS 1_4-20 X .75
Id Description
9 9784698 SCREW, HEX 1_4-20 X .50
10 9785853 ORBIT ARM - XVL10
11 9785907 SCREW, HEX CAP 1_4-20 X 2.75
12 9785912 CAN DRIVE WELDMENT
13 9785913 COUNTERWEIGHT - XVL10
14 9785914 BRACKET, COUNTERWEIGHT - XVL10

16 www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-852-1811
Owner’s Manual: XVL10
1785871 Rev J
ECO 15-0051 B
December 2015
9. orderIng
Replacement Parts
HOW TO ORDER REPLACEMENT PARTS
Replacement parts can be ordered from Red Devil Equipment Co. by telephone, fax, or email:
If you need help in determining the proper part(s) to order, please call Customer Care. at 1-800-221-1083.
Always indicate the Model and Serial numbers of the machine when ordering replacement parts.
GENERAL PARTS REPLACEMENT POLICIES
While your machine is under warranty, do not attempt on-site repair or parts replacement without first
contacting Red Devil Equipment Co. (to protect your warranty). After the warranty expires, replacement
parts and recommendations for on-site servicing are available from Red Devil Equipment Co. Please
Customer Care for assistance.
RESTOCKING FEE
A restocking fee will be charged on all unused parts which are returned.
RED DEVIL EQUIPMENT CO.
763-533-2969
800-221-1083
763-852-1811 (FAX)
[e-mail]

17
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-852-1811
1785871 Rev J
ECO 15-0051 B
December 2015
Owner’s Manual: XVL10
10. WarranTy
Equipment Covered Under This Warranty:
Model XVL10
Warranty
Red Devil Equipment Co. warrants equipment manufactured by it and bearing its name to be free from
defects in material and workmanship.
Red Devil Equipment Co. will provide replacement parts caused by failure due to production or
manufacturing error during the warranty period. Costs of labor and transportation for service of
machines under this warranty will also be covered during the warranty period. Normal ground freight
will be covered for replacement parts sent within the warranty period. UPS Ground or common carrier
ground freight will be covered for the return of defective items only.
This warranty applies only when the equipment is installed, operated, and maintained in accordance
with written Red Devil Equipment Co. instructions as appearing in the owners' manuals.
This warranty does not cover, and Red Devil Equipment Co. shall not be liable for, any malfunction,
damage, or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or
improper maintenance, negligence, accident, tampering, or substitution of non-Red Devil Equipment
Co. component parts, modification or use for non-intended purposes. Nor shall Red Devil Equipment
Co. be liable for malfunction, damage, or wear caused by the incompatibility of Red Devil Equipment Co.
equipment with structures, accessories, equipment, or materials not supplied by Red Devil Equipment
Co.
Disclaimers and Limitations
The terms of this warranty constitute purchaser's sole and exclusive remedy and are in lieu of any
other warranties, express or implied. In no case shall Red Devil Equipment Co.'s liability exceed the
amount of the purchase price. *All warranty repairs must be executed by a Red Devil Equipment Co.
Authorized Service Center or warranty will be voided.
Please contact your Red Devil Equipment Co. account representative at 800-221-1083 for specific
questions regarding warranty terms.

18 www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-852-1811
Owner’s Manual: XVL10
1785871 Rev J
ECO 15-0051 B
December 2015
noTes

19
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-852-1811
1785871 Rev J
ECO 15-0051 B
December 2015
Owner’s Manual: XVL10

For sales or service, please contact:
Red Devil Equipment Company
Attn: Customer Care Department
14900 21st Ave N
Plymouth, MN 55447
USA
U.S. Telephone:
International Telephone:
Fax:
E-mail:
800.221.1083
+1.763.533.2969
763.852.1811
[e-mail]
Copyright 2014 Red Devil Equipment Company. All rights reserved.
Owner’s Manual: XVL 10 1785871 Rev J
ECO 15-0051 B
December 2015
For instructional “How To” videos please visit
our youtube channel or go to
www.RedDevilEquipment.com