red lion DA USB Sled User manual

DAUSB - C
Drawing No. LP1127
Revised 12/2022
DA USB Sled
Installation Guide
1
PACKAGE CHECKLIST
This product package should contain the items listed below. If
any items are missing or damaged, contact Red Lion immediately.
- DA USB Sled
- Installation Guide
SAFETY SUMMARY
All safety related regulations, local codes and instructions that
appear in this document or on equipment must be observed to
ensure personal safety and to prevent damage to either the
device or equipment connected to it.
Do not use these products to replace proper safety interlocking.
No software-based device (or any other solid-state device) should
ever be designed to be responsible for the maintenance of
personnel safety or consequential equipment not equipped with
safeguards. Red Lion disclaims any responsibility for damages,
either direct or consequential, that result from the use of this
equipment in a manner not specified.
ORDERING INFORMATION
DESCRIPTION PART NUMBER
USB Host Sled DA S00 PN40U 400 000
Spaces in listed part numbers are shown to improve readability, do not
include when searching for or ordering these parts.
SPECIFICATIONS
1. POWER REQUIREMENTS: Power is supplied by the DA host
controller.
Max Power: 3 W
2. INTERFACES: USB 2.0
3. ENVIRONMENTAL CONDITIONS:
Operating Temperature Range: -40 to 75 °C TAMB
Storage Temperature Range: -40 to 80 °C TAMB
Vibration to IEC 60068-2-6: Operational 5-500 Hz, 2 g
Shock to IEC 60068-2-27: Operational 15 g
Operating and Storage Humidity: 0 to 95% max. RH non-
condensing
Altitude: Up to 2000 meters
4. CERTIFICATIONS AND COMPLIANCES:
CE Approved
EN 61326-1 Immunity to Industrial Locations
Emission CISPR 11 Class A
IEC/EN 61010-1
RoHS Compliant
ATEX Approved
II 3 G Ex ec IIC T4 Gc
DEMKO 20 ATEX 2268X
IECEx Approved
IECEx UL 20.0007X
UKEX Approved
UL22UKEX2576X
UL Hazardous: File # E317425
5. INSTALLATION REQUIREMENTS: Sled must be installed
inside the unit case with the hardware provided. See
“Installing the DA USB Sled” for more details
6. WEIGHT: 2.1 oz (65.32 g)
CAUTION: Risk of Danger
Read complete instructions prior to installation and
operation of the unit.
ATTENTION : Risque de danger
Lire les instructions complètes avant l’installation et
l’utilisation de l’appareil.
zHigh-Speed USB 2.0 host port
z500 mA capable
zIndustrial rated for harsh environments
zWide operating temperature range
zField installable
For use with DA50 and DA70 series covered in DEMKO 20 ATEX
2268X and IECEx UL 20.0007X certificates
FOR USE IN HAZARDOUS LOCATIONS:
Class I, Division 2, Groups A, B, C, and D
T4
C
C
US
US
UL
R
LISTED
IND.CONT. EQ.
E317425
II 3 G Ex ec IIC T4 Gc
DEMKO 20 ATEX 2268X
IECEx UL 20.0007X
UL22UKEX2576X

2
Drawing No. LP1127 Revised 12 2022
INSTALLING THE DA USB SLED
DA50 INSTALLATION
1. Prior to installing the Sled for your DA50 application, ensure
that the unit is not receiving power.
2. Disconnect and remove your DA50 from the DIN rail.
3. Remove the DA50 unit’s front cap by squeezing the sides and
pulling.
4. Slide out the sled holder.
5. Install a sled into the sled holder and hand tighten the captive
fasteners, or use a screwdriver.
6. Re-install the sled holder containing the sled into the
Converter. Make sure it is fully seated.
7. Replace the front cap.
DA70 INSTALLATION
1. Prior to installing the Sled(s)
for your DA70 Controller
application, ensure that the
Controller is not receiving
power.
2. Remove the carriage from the
Controller case by releasing
the two retaining latches and
pulling straight out from
Controller
3. Remove blank panel from the
carriage slot of the target sled
installation location.
4. Install sled by aligning the
two sled mounting hole
fasteners, with the controller
mounting posts. Be sure locating holes on bottom side of sled
align with the locating pins on the carriage, and the sled sits
flush against the carriage.
5. Hand tighten the sled captive fasteners, or use a screwdriver
if necessary.
6. Repeat the above steps for any additional sleds.
7. Carefully align the carriage with the Controller base and press
carriage into the controller.
8. Close the retaining latches to ensure the carriage is fully
seated into the Controller case.
COPYRIGHT
©2020 Red Lion Controls, Inc. All rights reserved. Red Lion
and the Red Lion logo are trademarks of Red Lion Controls,
Inc. All other company and product names are trademarks of
their respective owners.
CONFIGURING THE USB SLED
DA50N CONFIGURATION
When using the USB Sled in your installation, configuration and
access to a connected device can be accomplished through the
Linux command line. Mass storage devices may be mounted to a
directory of your choosing via the “mount” command.
DA50D or DA70D CONFIGURATION
The USB Host Sled is configured using Crimson 3.1 (or later)
software. After selecting the USB Host Sled, configure the
Memory Stick or Keyboard properties in the USB Host Ports
section. Find additional information in the Crimson 3.1 User
Manual.
SLED LED
The Sled LED provides status for both Sled power as well as
USB port power. This LED will light up Green once a USB device
is plugged into the port and power has been applied to it.
RED LION CONTROLS TECHNICAL SUPPORT
If for any reason you have trouble operating, connecting, or
simply have questions concerning your new DA USB sled, contact
Red Lion’s technical support.
Support: support.redlion.net
Website: www.redlion.net
Inside US: [phone]
Outside US: [phone]
Red Lion Controls, Inc.
35 Willow Springs Circle York, PA 17406
CAUTION: Follow standard ESD precautionary
procedures.
ATTENTION: Suivez les procédures de précaution
standard de décharge électrostatique.
WARNING - Disconnect all power to the unit before
installing or removing sleds.
AVERTISSEMENT - Débranchez l’alimentation électrique
de l’appareil avant d’installer ou de retirer les tiroirs.
CAUTION: Failure to properly align the carriage can
result in damage to the Sled connector pins.
ATTENTION: Si le tiroir n’est pas correctement
aligné, les broches du connecteur du tiroir risquent
d’être endommagées.
LIMITED WARRANTY
(a) Red Lion Controls Inc. (the “Company”) warrants that all
Products shall be free from defects in material and workmanship
under normal use for the period of me provided in “Statement
of Warranty Periods” (available at www.redlion.net) current at
the me of shipment of the Products (the “Warranty Period”).
EXCEPT FOR THE ABOVE-STATED WARRANTY, COMPANY
MAKES NO WARRANTY WHATSOEVER WITH RESPECT
TO THE PRODUCTS, INCLUDING ANY (A) WARRANTY OF
MERCHANTABILITY; (B) WARRANTY OF FITNESS FOR
A PARTICULAR PURPOSE; OR (C) WARRANTY AGAINST
INFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS OF
A THIRD PARTY; WHETHER EXPRESS OR IMPLIED BY LAW,
COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE
OF TRADE OR OTHERWISE. Customer shall be responsible for
determining that a Product is suitable for Customer’s use and that
such use complies with any applicable local, state or federal law.
(b) The Company shall not be liable for a breach of the warranty
set forth in paragraph (a) if (i) the defect is a result of Customer’s
failure to store, install, commission or maintain the Product
according to specicaons; (ii) Customer alters or repairs such
Product without the prior wrien consent of Company.
(c) Subject to paragraph (b), with respect to any such Product
during the Warranty Period, Company shall, in its sole discreon,
either (i) repair or replace the Product; or (ii) credit or refund the
price of Product provided that, if Company so requests, Customer
shall, at Company’s expense, return such Product to Company.
(d) THE REMEDIES SET FORTH IN PARAGRAPH (c) SHALL
BE THE CUSTOMER’S SOLE AND EXCLUSIVE REMEDY AND
COMPANY’S ENTIRE LIABILITY FOR ANY BREACH OF THE
LIMITED WARRANTY SET FORTH IN PARAGRAPH (a).
BY INSTALLING THIS PRODUCT, YOU AGREE TO THE TERMS
OF THIS WARRANTY, AS WELL AS ALL OTHER DISCLAIMERS
AND WARRANTIES IN THIS DOCUMENT.