Redarc Tow-Pro Elite User manual

Tow‑Pro®Elite
Electric Trailer Brake Controller
12 V or 24 V, 1 to 3 Axles
MODEL:
 EBRH‑ACCV3

2
Tow‑Pro®Elite
Electric Trailer Brake Controller (EBRH‑ACCV3)
The Tow‑Pro®Elite is an electric trailer brake controller designed to suit most common trailer braking
applications. It requires minimal dash space and is simple to install and operate.
The Tow‑Pro®Elite has selectable Proportional or User Controlled trailer braking modes so you can
choose the braking style that suits the road/terrain conditions or vehicle type.
The Tow‑Pro®Elite features Active Calibration which constantly monitors the direction of travel and
will even calibrate with no trailer attached, and can be mounted in any orientation.
The unit can operate electric trailer brakes from either 12 V or 24 V vehicle systems without the need
for manual selection or extra components or wiring.
The unit can operate Electric/Hydraulic trailer brakes from 24V vehicle systems when installed with a
suitable adapter such as a REDARC EB24A. The
Tow‑Pro®Elite is ADR compliant when installed
as directed and is approved for use with AL‑KO
ESC and Dexter DSC sway control systems.

Contents | 3
CONTENTS
1 WARNINGS AND SAFETY INSTRUCTIONS ���������������������������������������������������������������������4
2 KIT CONTENTS ��������������������������������������������������������������������������������������������������������������������6
3 SPECIFICATIONS �����������������������������������������������������������������������������������������������������������������7
3.1 Dimensions and Connection ��������������������������������������������������������������������������������������8
4 INSTALLATION ���������������������������������������������������������������������������������������������������������������������9
4.1 Mounting the Main Unit����������������������������������������������������������������������������������������������� 9
4.2 Wiring the Brake Controller���������������������������������������������������������������������������������������10
4.3 Brake Signal Source��������������������������������������������������������������������������������������������������14
4.4 Mounting the Remote Head �������������������������������������������������������������������������������������15
4.5 Active Calibration�������������������������������������������������������������������������������������������������������17
5 OPERATION ����������������������������������������������������������������������������������������������������������������������� 18
5.1 Adjusting the Braking Force �������������������������������������������������������������������������������������18
5.2 Manual Override���������������������������������������������������������������������������������������������������������18
5.3 Operating Modes�������������������������������������������������������������������������������������������������������19
5.4 Park Brake Feature����������������������������������������������������������������������������������������������������21
5.5 Visual User Guide ������������������������������������������������������������������������������������������������������21
5.6 AL‑KOiQ7 Compatibility�������������������������������������������������������������������������������������������22
5.7 LED Indication������������������������������������������������������������������������������������������������������������22
5.8 Troubleshooting ���������������������������������������������������������������������������������������������������������23
6 MAINTENANCEANDCHECKS ��������������������������������������������������������������������������������������� 25
7 FREQUENTLY ASKED QUESTIONS �������������������������������������������������������������������������������� 26
8 WARRANTY����������������������������������������������������������������������������������������������������������������������� 27

4 | Warnings and Safety Instructions
1 WARNINGS AND SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS — This manual contains important safety instructions for the
Tow‑Pro®Elite Electric Trailer Brake Controller.
Do not operate the controller unless you have read and understood this manual and the controller
is installed as per these installation instructions. REDARC recommends that the charger be installed
by a suitably qualified person.
SAFETY MESSAGE CONVENTIONS
Safety messages in this manual include a signal word to indicate the level of the hazard as follows:
WARNING: Indicates a potentially hazardous situation which could result in death or serious
injury to the operator or to bystanders.
CAUTION: Indicates a potentially hazardous situation which may result in moderate or minor
injury to the operator or to bystanders.
NOTICE: Indicates a situation that may cause equipment damage.
WARNING
• Ensure that your trailer brakes are installed and are operating correctly;
Improperly installed and/or faulty trailer brakes can cause erratic vehicle or trailer behaviour
with the potential to cause a road accident. For this reason, it is of utmost importance that
your trailer braking system be installed/maintained by a qualified installer.
• Always check brakes at low speed each time a trailer is attached to your vehicle.
• Early sign of problems related to the safety and integrity of the braking system need to
be investigated and corrected with urgency including, but not limited to: locking of trailer
brakes, brake‑away system not operating or incorrectly fused, permanent illumination of
vehicle stop lamps and/or dashboard warning lamps.
Left unchecked these type of issues can involve loss of braking and/or severe damage of the
equipment and the vehicle.
CAUTION
1. Ensure that the Tow‑Pro®Elite is mounted securely in a fixed location. Failure to mount
securely will result in inaccurate braking force measurements and incorrect braking of the
trailer.
2. Ensure that the Tow‑Pro®Elite is installed inside the vehicle cabin and away from any
environmental conditions that may cause damage, including engine heat, submersion in
water, salt spray and humidity. Exposure to these conditions may cause damage to the
unit’s circuitry and may cause erratic trailer braking.
3. A Fuse or Circuit Breaker of appropriate rating must be installed to protect the vehicle
system. Please refer to the installation instructions starting on page 9for specific
instructions on where to install the Fuse or Circuit Breaker and for appropriate Fuse or
Circuit Breaker rating. The Fuse or Circuit Breaker must be installed as close as possible to
the battery.

Warnings and Safety Instructions | 5
4. Ensure the remote head push‑button activates correctly when installed into surfaces with
a thickness greater than 3.75mm (0.15"). Failure to activate correctly would result in not
being able to activate the override function or change modes.
5. Ensure that the wire(s) and all connections used to install the Tow‑Pro®Elite are suitably
rated to supply the required current to simultaneously operate the trailer electric brakes and
stop lamps. Incorrect wiring can result in reduced (or total loss of) trailer braking and/or
damage to property or persons.
6. The Tow‑Pro®Elite is suitable for trailers with electric brakes up to three axles. Note that
Federal and State laws apply to trailer weights and brake controller requirements. Please
consult your local authority to ensure you comply with the legal requirements.
7. Do not tow with the Tow‑Pro®Elite while a fault code is active. Fault codes of the
Tow‑Pro®Elite may indicate conditions that make it unsafe or illegal to tow, including
unreliable trailer brakes or failure of brake lights.
8. During the calibration step of the Tow‑Pro®Elite, braking of the trailer may be inconsistent.
REDARC recommends calibrating the Tow‑Pro®Elite without a trailer attached. A normal
drive of a few kilometres will do for this purpose. If calibrating with a trailer attached, then
the recommended setting for the Tow‑Pro®Elite is 4 or less.
NOTICE
1. Ensure that a correct grounding point is used. Vehicles often have ungrounded metal
reinforcements under the dash and these points are not suitable grounds. Bad grounding of
the unit will result in poor or no operation.
2. The Tow‑Pro®Elite does not act as a trailer lights voltage converter. If the trailer brake lights
operate on a different voltage, damage to the vehicle; trailer and/or Tow‑Pro®Elite and
associated wiring may result. This may also result in reduced (or total loss of) trailer braking.
3. When installing the Tow‑Pro®Elite Remote Control to a thin panel, washers are
recommended to reinforce the structure of the panel.
4. Do NOT exceed Tow Vehicle and Trailer weights and specifications. Failure to abide by the
towing regulations, including maximum loads, may result in a fine, or in case of an accident,
refusal of the insurance claim, and the possibility of further legal action.
5. If no trailer is connected, Active Calibration may occur as normal without any indication from
the LED. The LED will already be Blue when the trailer is connected. Essentially, whether
a trailer is connected or not, just drive normally and Active Calibration will ensure the
Tow‑Pro®Elite learns the correct direction of travel.

6 | Kit Contents
2 KIT CONTENTS
1
34
7
5
8
6
2
1Main Unit
2Remote Head Assembly
3Remote Head Body
4Remote Head Nut
5Remote Head Knob
6Remote Head Bezel
7Main Unit Wires and Connector 0.5 m (1'7")
8Remote Head Cable 1m (3'3")

Specications | 7
3 SPECIFICATIONS
Part Number EBRH‑ACCV3
Operating Voltage 9V to 32V
Nominal Input System Voltage 12 V 24 V
Brake Input Signal Voltage OFF: 0 V
ON: +12 V nominal
OFF: 0 V
ON: +24 V nominal
Brake Coil Voltage 12 V
Max. Trailer Axles 3 Axles
Nominal Current Draw 18 A
Max. Rated Current 25 A 30 A
Standby Current <5 mA
Operating Temp –20°C to +60°C (−4°F to 140°F)
Weight 200 g (7.05 oz)
Warranty 2 years

8 | Specications
3.1 DIMENSIONS AND CONNECTION
10.0mm (0.39") 10.0mm (0.39")
Brake
Lights
(RED)
Input
Power
(BLACK)
Ground/
Earth
(WHITE)
Brake
Output
(BLUE)
Remote Head
Connection
19.6mm
(0.77")
14.7mm
(0.58") (Recommended)
11.5mm (0.45")
20.0mm
(0.79")
20.0mm
(0.79")
20mm
(0.79")
31.7mm
(1.25")
30.0mm
(1.18")
84.5 mm (3.33")
67mm (2.64")
74mm (2.92")
100.0mm (3.94")
104.0mm (4.09")
28.8mm
(1.13")

Installation | 9
4 INSTALLATION
4.1 MOUNTING THE MAIN UNIT
The Tow‑Pro®Elite should be mounted inside the vehicle cabin using either M4 (5⁄32") diameter
screws or other secure fitting methods at the mounting points provided. It is essential to mount the
unit in a location which allows access to the intended remote head location.
The Tow‑Pro®Elite can be mounted in any orientation as long as the installation is secure and
the main unit cannot move or change orientation once installed. A change of orientation will affect
the system calibration.
CAUTION
• Ensure that the Tow‑Pro®Elite is mounted securely in a fixed location. Failure to mount securely
will result in inaccurate braking force measurements and incorrect braking of the trailer.
• Ensure that the Tow‑Pro®Elite is installed inside the vehicle cabin and away from any
environmental conditions that may cause damage, including engine heat, submersion in
water, salt spray and humidity. Exposure to these conditions may cause damage to the unit’s
circuitry and may cause erratic trailer braking.
Any secure location ok
Do Not Mount to
Cables/Wiring Looms
(Must be mounted to a
solid object or surface)

10 | Installation
4.2 WIRING THE BRAKE CONTROLLER
CAUTION
• A Fuse or Circuit Breaker of appropriate rating must be installed to protect the vehicle system.
Please refer to the installation instructions starting on page 9 for specific instructions on
where to install the Fuse or Circuit Breaker and for appropriate Fuse or Circuit Breaker rating.
The Fuse or Circuit Breaker must be installed as close as possible to the battery.
• Ensure that the wire(s) and all connections used to install the Tow‑Pro®Elite are suitably
rated to supply the required current to simultaneously operate the trailer electric brakes and
stop lamps. Incorrect wiring can result in reduced (or total loss of) trailer braking and/or
damage to property or persons.
NOTICE: The Tow‑Pro®Elite does not act as a trailer lights voltage converter. If the trailer brake
lights operate on a different voltage, damage to the vehicle; trailer and/or Tow‑Pro®Elite and
associated wiring may result. This may also result in reduced (or total loss of) trailer braking.
4.2.1 RED WIRE (VEHICLE BRAKE LIGHT) CONNECTION
The requirements for a suitable connection of a brake controller trigger wire are quite specific.
This connection point must:
• Provide a voltage of the same voltage level as the “Start Battery*” while the vehicle
brakes are applied.
• Have 0 V output while the vehicle brakes are not applied.
• Accept battery voltage input when the brake controller manual override is operated and
illuminate at least the trailer brake lights.
• Accept the battery voltage input as above without causing any damage, spurious vehicle
operation or erroneous fault indication.
A relay should not be installed to drive the red wire as this would prevent the override feature from
working and may introduce dangerous voltage spikes.
For many vehicles, the brake light terminal of the trailer lighting socket provides a suitable
connection, however this is not necessarily suitable for all vehicles. Unfortunately REDARC
cannot recommend where to make this connection on a specific vehicle's OEM wiring. For further
information contact the vehicle manufacturer.
* Start Battery voltage output means directly from the Start Battery and within 0.4 V of Supply (Black wire) voltage.

Installation | 11
4.2.2 WIRING — ELECTRIC BRAKES
For 12 V and 24 V vehicle electrical systems, the Tow‑Pro®Elite is designed to operate electric
brakes without the need for any additional converters.
To 12V Vehicle
Brake Light trigger
To 12V Electric
Trailer Brakes
BLUE
RED
25A Fuse or
30A Circuit Breaker
(CBK30-EB)
12V Vehicle
Start Battery
Ground
BLACK
Dash mount
controls for
Tow-Pro
WHITE
1.25 mm
(14 AWG)
3.0 mm
(12 AWG)
3.0 mm
(12 AWG)
1.25 mm
(14 AWG)
Ground
12V
INPUT
For wire selection refer to the wiring gauge guide in Section4.2.5 (page14).
For red wire selection refer to Section4.2.1 (page10).
NOTICE
The Input Power (Black) wire must be connected directly to the positive terminal of the start
battery via a Fuse (25 A) or Circuit Breaker (30 A) and not through an Ignition source.
To 24V Vehicle
Brake Light trigger
To 12V Electric
Trailer Brakes
25A Fuse or
30A Circuit Breaker
(CBK30-EB)
24V Vehicle
Start Battery
Dash mount
controls for
Tow-Pro
Ground
24V
INPUT
Ground
1.25 mm
(14 AWG)
3.0 mm
(12 AWG)
3.0 mm
(12 AWG)
1.25 mm
(14 AWG)
BLUE
RED
BLACK
WHITE
For red wire selection refer to Section4.2.1 (page10).

12 | Installation
4.2.3 WIRING — ELECTRIC/HYDRAULIC BRAKES
NOTICE: Always refer to the manufacturer’s specifications for your Electric/Hydraulic Braking
system prior to installation and usage of the Tow‑Pro®Elite.
12 V VEHICLE SYSTEMS
The Tow‑Pro®Elite is designed to operate both Electric trailer brake systems and 12V
Electric/Hydraulic trailer brake systems. However, most Electric/Hydraulic systems require a separate
12V power feed for the hydraulic pump. For example:
Electric / Hydraulic
System
Power Supply for
Electric/Hydraulic System
Output Wire (Blue)
Tow-Pro
Brake
Signal
12 V Start
Battery
To 12 V Vehicle Brake
Light Trigger
To Electric / Hydraulic
Brake System
BLUE
RED
25A Fuse or
30A Circuit Breaker
(CBK30-EB)
12V Vehicle
Start Battery
BLACK
Dash-mount
Controls for
Tow-Pro
WHITE
Power Supply for
Electric / Hydraulic
Brake System
Refer to Electric / Hydraulic system
manufacturer specications for power
supply wire gauge and fuse rating
Ground
Ground
1.25 mm
(14 AWG)
3.0 mm
(12 AWG)
3.0 mm
(12 AWG)
1.25 mm
(14 AWG)
12V
INPUT
For red wire connection, see Section4.2.1 (page10).

Installation | 13
24 V VEHICLE SYSTEMS
Both Electric / Hydraulic braking and ESC systems can be sensitive to 24V inputs depending on
the electronics within the hydraulic pump system or the ESC system. To supply a 12 V input to the
Electric / Hydraulic or an ESC system, a REDARC EB24A can be used in a 24V vehicle to provide
12 V Red and Black wires of the Tow‑Pro®Elite. For example:
IGN
EB24A Tow-Pro
Output Wire (blue)
24V Vehicle Brake Light Trigger
To 24V System
24V Battery Setup
Power Supply for Electric/Hydraulic
Actuator OR ESC System
Electric/Hydraulic
Actuator OR
ESC System
THE REDARC EB24A
• Converts a 24 V brake signal to a 12 V signal for the Tow‑Pro®Elite (Red wire).
• Allows the Tow‑Pro®Elite override button to switch on 24 V brake lights.
• Provides charge equalisation of the supply batteries so 12 V can be supplied
from the 24 V battery bank.
24V
INPUT
To 24V Vehicle
Brake Light Trigger
To Electric / Hydraulic
Brake System
RED
BLUE
25A Fuse or
30A Circuit Breaker
(CBK30-EB)
24V Vehicle Start Battery
WHITE
BLACK
Ground
Relay
PINK
GREEN
To Vehicle
Ignition
To 24V System RED
EB24A
Adaptor
10A
Fuse
10A
Fuse
BROWN
PURPLE
Power Supply
for Electric/Hydraulic
Brake System
Dash mount
controls for
Tow-Pro
1.25 mm
(14 AWG)
3.0 mm
(12 AWG)
3.0 mm
(12 AWG) 3.0 mm
(12 AWG)
3.0 mm
(12 AWG)
1.25 mm
(14 AWG)
For red wire connection, see Section4.2.1 (page10).

14 | Installation
4.2.4 WIRING — VEHICLES WITH CAN BUS SYSTEM
Many modern vehicles use a CAN Bus system for signalling when to apply the vehicles brakes
as required by safety systems including adaptive cruise control, stability control, Autonomous
Emergency Braking (AEB) and hill descent control. For these vehicles, REDARC recommend the
following wiring configuration.
RED
WHITE
Trailer Brake
Light Wire
from Vehicle
IMPORTANT
If the Brake signal
source is the Brake
Light Terminal of the
Trailer Plug. A Diode
MUST be used.
Trailer Brake STOP
Light PIN #6
To Pin #5 of the
Trailer Plug
BLUE
30A Circuit Breaker
(CBK30-EB)
To Vehicle
Start Battery
BLACK
Dash mount
controls for
Tow-Pro To Chassis
Ground Bolt
1.25 mm
(14 AWG) Diode (EPOK-001)
3.0 mm
(12 AWG)
3.0 mm
(12 AWG)
1.25 mm
(14 AWG)
4.2.5 WIRING GAUGE GUIDE
This diagram outlines the required wire cross sectional areas for the Tow‑Pro®Elite installations
detailed in Section4.2 (page10).
All wire ratings refer to the minimum required cross sectional area of copper only (not including
insulation). Always use a wire gauge equal to or greater than what is specified in this guide.
Red
1.25mm
AWG16
White
1.25mm
AWG16
3mm
Blue
AWG12
6mm
Black (24V)
AWG9
3mm
Black (12V)
AWG12
4.3 BRAKE SIGNAL SOURCE
Brake Light terminal of Trailer Plug
For CAN Bus vehicles, REDARC recommend sourcing the brake signal from the brake light wire of
the trailer plug as it will capture all braking events that illuminate the vehicle brake lights.
Please note that if the brake signal is sourced at the trailer plug, a diode MUST be fitted on the
vehicles brake light wire on the vehicle side of the point where the brake signal is sourced.
This prevents the back feeding of the 12 V into the vehicle when the Tow‑Pro®Elite is manually
activated whilst illuminating the trailer brake lights.
Trailer Brake
Light Wire
from Vehicle
Tow-Pro Elite
Brake Signal Wire
Trailer Plug
Brake Light Wire
Wire Diagram
Scale (mm)
0 5 10 15 20 25 30 35

Installation | 15
4.3.1 BRAKE PEDAL SWITCH
Sourcing the brake signal at the brake pedal will only detect braking events when the brake pedal
is depressed (and the switch activated) and not brake applications activated by other on board
systems such as AEB.
NOTE: Only connect to the brake pedal switch of specified by vehicle manufacturer.
4.4 MOUNTING THE REMOTE HEAD
The Tow‑Pro®Elite remote head is designed to be mounted at a distance from the main unit,
allowing for a neat, convenient installation and not impeding on lower leg airbags or driver leg room.
The Tow‑Pro®Elite remote head is designed to be mounted on or around the vehicle dashboard and
when installed correctly, complies with Australian Design Rule (ADR) 21, which sets requirements for
devices mounted on the dashboard.
The Tow‑Pro®Elite remote head can be mounted directly to the dashboard, to the centre console or
through a spare knock‑out switch panel and requires only one hole to be drilled as per the Mounting
Guide in Section 4.4.2 on page 16. For easy access in an emergency situation, REDARC
recommend installing the remote head within reach of the driver such as the regions shaded in the
diagram.
4.4.1 INSTALLATION ACCESSORIES
REDARC offer a range of vehicle specific switch inserts and
vehicle specific wiring kits designed to make the installation of the
Tow‑Pro®Elite easier.
A full listing of Switch Inserts and Wiring Kits is available for
purchase on the REDARC website.

16 | Installation
4.4.2 MOUNTING THE REMOTE HEAD ON A DASH OR CONSOLE PANEL
Ensure that there is enough space behind the mounting location to fit the Tow‑Pro control head and
remote head cable before drilling any holes.
10mm
(25/64")
1.25 – 3.6 mm
(1/16" – 9/64")
1Drill a small pilot hole, then Drill a 10 mm
(25⁄64") mounting hole. 2
Gently bend bezel to aid removal of
white backing tape. Apply adhesive bezel
(optional) to cleaned surface.
0.8Nm
(0.6 lbf-ft)
3Insert Remote Head shaft through the
hole and fasten with nut. 4Turn shaft fully anti‑clockwise.
Level marker
5Apply knob with ‘0’ aligned to level
marker on the bezel. 6Test installed remote head for correct function.
CAUTION: Ensure the remote head push‑button activates correctly when installed into
panels with a thickness greater than 3.75 mm (1⁄8"). Failure to activate correctly would result in
not being able to activate the override function or change modes.

Installation | 17
4.5 ACTIVE CALIBRATION
When the unit is first powered, Active Calibration must first become confident in the
vehicle direction of travel. Until this time the LED will flash Blue/Green.
During Calibration Once Calibrated
Time Time
Active Calibration constantly monitors the vehicle’s direction of travel and allows the Tow‑Pro®Elite
to ‘learn’ and continuously confirm its mounting orientation. This process occurs whilst the vehicle is
moving and the brake is applied and will occur with or without a trailer connected.
When the Tow‑Pro®Elite is first installed it will begin learning its mounting orientation through Active
Calibration as soon as you start driving, at this point Proportional Mode is selected but not yet fully
operational.
Until the Tow‑Pro®Elite has determined its mounting orientation the unit will function as if in
User‑Controlled mode, this is indicated by the LED glowing green with blue flashes. As the
Tow‑Pro®Elite becomes more confident of its direction of travel the length of the Blue flash will
increase, to the point that the LED is solid Blue which indicates it is now operating completely in
Proportional mode.
Under normal driving conditions the Tow‑Pro®Elite will learn its mounting orientation within 20 brake
applications. Note that the braking must be perceptible (applying the brake while stopped will not
assist calibration).
If power is disconnected (for example, if the vehicle battery is changed) calibration memory will be
lost and the unit will recalibrate itself using active calibration. This is similar to a radio losing its clock
or preset station memory.
NOTICE: If no trailer is connected, Active Calibration may occur as normal without any
indication from the LED. The LED will already be Blue when the trailer is connected. Essentially,
whether a trailer is connected or not, just drive normally and Active Calibration will ensure the
Tow‑Pro®Elite learns the correct direction of travel.

18 | Operation
5 OPERATION
5.1 ADJUSTING THE BRAKING FORCE
In both modes the braking level can be adjusted to suit varying trailer loads,
braking requirements or user comfort by adjusting the control knob on the
remote head.
The lower end of the scale (below level 5) should be used as a starting point
and adjusted accordingly once braking requirements are established.
If a lighter braking level is required, turn the control knob to a lower number (anti‑clockwise) to
reduce the trailer braking force. Similarly, turn control knob to a higher number (clockwise) to
increase the trailer braking force.
The braking level will be indicated by the LED changing to a shade of RED when the brakes are
applied. The higher the braking level, the more RED the LED will glow.
A setting of ‘0’ will result in no trailer braking output.
5.2 MANUAL OVERRIDE
Pressing the gain control knob whilst driving will apply the manual override
brake. The manual override brake will apply the trailer brakes only, and
will also apply the trailer brake lights and will turn the LED indicator RED.
Depending on the vehicle wiring it may also apply the vehicle brake lights.
The manual override is designed to be used when the trailer brakes need
to be applied without the vehicle brakes, such as correcting trailer ‘sway’
whilst travelling.
In Proportional mode the manual override will apply the trailer brake to a
level equivalent to ‘light’ vehicle braking.
In User Controlled mode the manual override will apply the trailer brakes
to the level set on the gain control knob.
In both modes the braking force can be adjusted by turning the gain control knob, either higher or
lower, even whilst applying the manual override brakes.
Manual override should not be used in place of the regular vehicle brakes.
2x
2
0
4
6
8
10

Operation | 19
5.3 OPERATING MODES
The Tow‑Pro®Elite offers two modes of operation — Proportional and User Controlled. On the
first application of power to the black wire, the Tow‑Pro®Elite will start‑up in Proportional mode.
Every time a trailer is connected, the Tow‑Pro®Elite will start up in the mode that was last selected
(provided the black wire has remained connected to power/battery positive).
5.3.1 PROPORTIONAL MODE (BLUE LED)
If the status indication LED on the control knob is glowing BLUE,
the Tow‑Pro®Elite is in Proportional Mode.
In Proportional Mode, the Tow‑Pro®Elite will apply the trailer brakes
at a level proportional to the vehicle deceleration. The control knob
setting, 0 to 10, will set the brakes from a lighter to a heavier trailer
brake application. Simply put, the harder the vehicle brakes are
applied, the harder the trailer will brake. This mode is designed
for highway travelling or everyday use and requires minimal input
from the user whilst travelling.
2
0
4
6
8
10
5.3.2 USER CONTROLLED MODE (GREEN LED)
If the status indication LED on the control knob is glowing GREEN,
the Tow‑Pro®Elite is in User Controlled Mode.
In User Controlled Mode, the Tow‑Pro®Elite will apply the trailer
brakes to the level set by the user on the gain control knob. The
control knob setting, 0 to 10, will set the brakes from Zero to Full
trailer brake application. Simply put, the trailer will brake to
the level set by the control knob (regardless of how hard
the vehicle brakes). This mode is often preferred for off road or
precision use and may require frequent attention from the user.
2
0
4
6
8
10
NOTICE: It is important to consider the road surface and conditions when selecting a mode and
level setting. When changing conditions we advise to review your controller settings and adjust
according to your preference.

20 | Operation
5.3.3 CHANGING MODES
Changing modes can only be completed with a trailer connected. Ensure the vehicle has come to a
complete stop before beginning the mode change process.
Changing between modes requires the user to complete the following process:
1Rotate the knob fully counter‑clockwise. 2Apply Vehicle Brakes.
2x
3Double‑click the knob
(two pushes within 1 second). 4Release Vehicle Brakes.
NOTICE: If you are unable to change modes, check that the remote head is not installed into a
panel which is too thick and that the button is able to be depressed fully. Refer to Section4.4
(page15)for details.
Ensure you reset the Control Knob to a suitable braking level after changing modes.