RedHealth c. Balance User manual

1
RedHealth c. Balance - Circadian Balance
User Guide
The RedHealth c. Balance unit is a non-invasive electronic device
specifically developed for personal use. It offers the capacity to enhance
general wellbeing, maintain circadian (body clock) rhythms and counteract
the effects of electro pollution (EMF). It has user selectable programs
designed to calm emotions, aid sleep patterns, ease pain and revitalize
energy levels. The c. Balance can also be ‘personalized’, calibrating the
inbuilt wellbeing programs to relate to the individual user.
The device utilizes ultra-low-level pulsed magnetic fields designed to resonate
with the body’s natural acupuncture meridian system and provide support for
the body’s natural self-regulating and adaption mechanisms.
This user guide explains the use and operation of the c. Balance unit.

2
About the Device
The c. Balance unit offers two categories of wellbeing programs:
Manual User programs – selected by the user can and used as and when
required. These provide the potential to calm emotions, aid sleep patterns,
ease pain, and revitalize energy levels.
Automated Background programs – run automatically at preselected times
of the day and night. These are designed to generally aid wellbeing by
maintaining circadian rhythms (24-hour body clock), aid brain wave states,
counteract the effects of EMF pollution and reduce stress. They also help
activate the body and mind in the morning and prepare it for sleep in the
evening.
In addition, the background programs can be recalibrated and uniquely
personalized to match with the user, adding potency and depth to the
therapeutic effects.
All features are accessed via two buttons on the control panel. The right ‘Set’
button gives direct access to the user programs and starts the ‘Personalize’
feature; the left ‘Status’ button is used to display the battery level and the
current time. As an additional procedure, the buttons can be pressed
together to initialize the ‘Personalize’ feature and to recalibrate the
background programs to specifically relate to the user.

3
User Programs
Single consecutive presses of the right ‘Set’ button will activate each of the
manual user programs in turn. The first press will activate ‘CALM’ as indicated
by the flashing red light, a second press will activate ‘SLEEP’, a third press
‘EASE’ and the fourth will activate ‘REVIT’
(revitalize).
A flashing red light against a user program along
with the pulsating central yellow light indicates it is
active and will stay active for a preset time of
between 14 and 25 minutes (depending on the
program) and then will automatically end.
The programs can be manually stopped at any
stage by pressing the ‘Set’ button several times to
advance to ‘REVIT’ and pressed once more for OFF.
Description of User Programs:
Calm: This program is designed to work with both acute and chronic stress
and anxiety and offers the potential for a general calming and relaxing
effect, promoting a quieter and more peaceful mind. The program runs for 15
minutes.
Sleep: Helps establish improved sleep patterns. It is best used a little before
retiring to bed. If waking during the night the Calm program may be more
effective than using the Sleep setting but do experiment. The run time is 25
minutes.
Ease: The aim of this program is to soothe nerve pain, reducing its intensity
and help relax muscular and mental tension. When muscle tensions are
reduced the experience of pain changes. It becomes less dominant or goes
completely. The Ease program also incorporates a ‘rejuvenate’ element to
aid the natural rejuvenation of damaged tissues. The program runs for 14
minutes and if required can be used several times in succession several times
a day. Ease can be used in most instances where pain is experienced and is
generally used over the area of discomfort.

4
Revit (Revitalize): This program aims to aid with the reestablishment of a sense
of vitality when feeling depleted. Run time is 14 minutes.
Note: The action of each of the user program may be enhanced by placing
the device over relevant acupoints as described in the ‘suggested use’
guide.
Setting the Time
Built into the c. Balance unit is a clock that maintains synchronization
between the background programs and the time of day. It is important to set
the clock correctly to ensure the background programs are activated at the
optimum time of day.
There are two ways of how the correct time can be set.
1. Set time to Midday
For correct setting the time this method can only be used at Midday.
Press the left button once and release (show battery level) and then press
once more and hold in while the time is indicated. After a couple of seconds
the HR, AM and PM lights will flash three times to indicate the time has been
set to midday. Release the button.
NOTE: If the clock is in stop mode (following a battery discharge below a
critical level) the time will not be shown, only the Time indicator will be on and
the HR, AM and PM will remain off. Setting the time will reactivate the clock.

5
2. Set time to any full hour
This method requires more details, but the time can be set to any desired full
hour.
1 - Press the
left button 2
times to
indicate
‘TIME’.
2 - Press the
right button
once and the
clock
indicator,
‘AM’, ‘PM’
and ‘HR’
lights will flash
three times
indicating the time has been cleared
to midnight and a new time can be
set.
3 – After
clearing the
time, the
new time is
set by
pressing the
right button.
Each press of
the left
button will flash the ‘HR’ light and
increment the time by one hour (1am,
2am, 3am…).
4 - After 12
presses ‘PM’
will change to
‘PM’
(indicating
midday).
Continuing to
press the Set
button will
increment the time (1pm, 2pm, 3pm…).
When the current time is reached, stop
pressing the set button and after a few
seconds the lights will go out and the
time is then set.
NOTE: the time can only be set to the nearest hour; there are no minute
settings. Ideally set the clock when the time is at or near the hour point.
However, for practical purposes it is fine to have the time set to within 15
minutes of the actual time.
After setting the time, check that it is correct.

6
Display the Time
To display the time, press the left button twice (TIME indictor).
Then either the ‘am’ or ‘pm’ indictor will show and the ‘HR’
indicator will flash once for each hour.
E.g. if ‘PM’ is indicated and the ‘HR’ indicator blinks 4 times, this is
4pm.
If ‘AM’ is indicated and there are no ‘HR’ blinks then it is 12am
(midnight)
If ‘PM’ is indicated and there are no ‘HR’ blinks then it is 12pm
(midday).
NOTE: if the ‘TIME’ is indicated but neither ‘AM’ nor ‘PM’ are, then the clock is
not being set.
Personalizing the Background Programs
The Personalize function automatically calibrates the background programs
to match with the users’ current state. Place the unit on the body, over the
heart is a good place.
There are two ways for initiating the Personalize feature:
1. Press and hold the right Set button. Release when the LEDs start flashing.
2. Press both the set and status buttons at the same time.
The central yellow light will come on and the indicator lights will flash on and
off in a clockwise direction for about 20 seconds as the personalization
process is running. When it is finished, the lights will go out and the unit
resumes to auto background mode.
NOTE: personalize only works if the time has been set.
NOTE: The personalize settings will remain set for 21 days and are then
automatically cleared. This happens as the body changes over time and the
unit needs to re-synchronize on a regular basis with a maximum of 21 days.
When the personalize-settings are cleared, the device reverts to default
program settings.

7
Battery Level
The battery level is indicated by pressing the left ‘Set’ button
once where the yellow battery indicator and several red
lights will come on. The number of red lights indicates the
battery level:
• 4 red lights = fully charged
• 3 red lights = good level of charge
• 2 red lights = lower level of charge
• 1 red light = low charge
• Yellow battery light flashing = discharged
The battery level will show for a couple of seconds and then all the lights will
go out.
Charging the Battery
The built in rechargeable battery is charged by
inserting a micro USB lead into the socket in the side
of the unit and connecting the other end into a USB
charger or USB port on a computer. To open the USB
port dust cover, insert a small screwdriver into the grove
as shown and gently lever it open.
When charging the yellow battery light on the front
panel will be illuminated and will stay illuminated for as
long as the charger is attached. To check the battery level during charging it
is best to disconnect the charging lead, wait a few moments and then hold in
the button on the front panel until the battery light shows. A fully charged
battery (four red lights) will give at least a month’s use of background
programs.

8
The time required to charge the battery will depend on how discharged the
battery is. If the battery level is at two red lights then a full charge will take
around 7 hours. If the battery is fully discharged (flashing battery light) then a
soak charge of 20 hours is recommended.
NOTE: If the battery is left in a depleted state then the unit will go into
hibernation mode and the background programs and user programs will no
longer run. When the left button is pressed, depending on the batter
discharge state, either the battery light will flash a few times or will not light at
all. It is necessary to recharge the unit to make it active again.
NOTE: If the unit is going to remain unused for several months then it is
recommended to fully charge the unit, put it into sleep mode and give it a
recharge every six months to preserve the battery. If the battery is left fully
discharged then it may start to deteriorate.
Putting the unit into Sleep Mode:
The unit can be put into sleep mode when not being used to save battery
power and the effective output from the unit is stopped, however the clock
will keep time. To put the unit into sleep mode press and keep holding in the
left button where first the battery level will be indicated and then after a
couple of seconds all the red lights will show and go out one at a time in a
clockwise direction indicating the device is in sleep mode. Let go of the
button.
To wake from sleep mode press in and hold the left button until the red lights
start to light up one at a time in an anticlockwise direction before they all go
out. The unit is then in the normal operating mode.
Note: When sleep mode is entered the personalization-settings are cleared so
it will be necessary to re-personalize the unit after waking from sleep mode.

9
Use
• The unit is sealed against water ingress and will tolerate being wet and
submerged in shallow water for a short length of time. However, it is not
designed to be used when swimming or to be subject to high-pressure
of water. It is recommended to keep the unit dry as much as possible.
• The unit is tolerant of shock loads but do not subject it to excessive
loads or constant vibration.
• Its operating temperature range is -5°C to +40°C.
• Clean with a damp cloth only - do not use chemicals.
• Only charge the unit from a standard USB charger outlet.
Disclaimer
All indications for using the device in this guide are suggestions for trial and
personal use only. This product does not claim to diagnose, treat, cure or
prevent disease. If you have a medical concern or condition, consult an
appropriate health care professional. This product has not been evaluated by
any medical government agency or medical regulatory organization.
© 2018 All rights reserved
Rev 1-1