Redline Engineering 2200HD User manual

2200 LBS
ELECTRIC
ATV/MOTORCYCLE LIFT
Instruction Manual
Please read this instruction manual carefully before use.

IMPORTANT
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFETY INSTRUCTIONS AND
WARNINGS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE WHICH IT IS
INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE TO PROPERTY AND/OR PERSONAL INJURY.
PLEASE KEEP THIS INSTRUCTION MANUAL SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS AND WARNINGS
1.1 Use a qualified person to maintain the lift in good condition. Keep it clean for best performance.
1.2 The maximum load is 2200lbs. DO NOT exceed this rated capacity.
1.3 Use this lift for lifting purpose only. DO NOT use it for any other purpose it is not designed to
perform.
1.4 Keep children and unauthorized persons away from the work area.
1.5 Remove ill fitting clothing. Remove ties, watches, rings and other loose jewelry, and tie up long
hair.
1.6 Wear ANSI approved safety goggles when operating the lift.
1.7 Keep proper balance and footing, do not overreach and wear nonskid footwear.
1.8 Only use this lift on a surface that is stable, level, dry and not slippery, and capable of sustaining
the load. Keep the surface clean, tidy and free from unrelated materials and ensure that there is
adequate lighting.
1.9 Before lifting load, stabilize the lift by turning the adjusting screws down. The lift must only be
used in a static position for lifting and lowering loads. Ensure that the load remains stable at all
times.
1.10 Ensure the load is adequately secured to the lift with appropriate straps.
1.11 Before lowering lift ensure that there are no obstructions underneath and that all people present
are standing clear.
1.12 Always keep your hands and feet away from moving parts.
1.14 DO NOT use the lift if damaged, or any suspect parts are subjected to a shock load.
1.15 DO NOT operate the lift when you are tired or under the influence of alcohol, drugs or any
intoxicating medication.
1.16 DO NOT allow untrained individuals to operate the lift.
1.17 DO NOT make any modifications to the lift.
1.18 DO NOT expose the lift to rain or snow.

EXPLODED DRAWING

NO.
DESCRIPTION
Q'TY
NO.
DESCRIPTION
Q'TY
1
SIDE EXTENSION
2
34
CONNECT BAR
1
2
PLATE FORM
1
35
FIXED HINGE
1
3
BAFFLE PLATE
1
36
PLATE FOR SUPPORT
1
4
VISE
1
37
WASHER
9
5
BOLT
12
38
BOLT
9
6
WASHER
12
39
SAFTY BASE
4
7
NUT
10
40
WHEEL
2
8
HOOK BASE
2
41
RAM ASSY
1
9
END CAP
4
42
CLIP
4
10
PIN
4
43
PIN
1
11
STATIONARY RING
4
44
PIN
2
12
CONNECT TUBE
2
45
PIN
1
13
NON-SLIP PLATE
1
46
PIN
2
14
SCREW
4
47
BASE FRAME ASSY
1
15
PIN
2
48
SEAL RING
4
16
WASHER
2
49
OIL CONNECTOR FOR RAM
1
17
BOLT
2
50
OIL HOSE
1
18
SET BLOCK
6
51
OIL CONNECTOR FOR PUMP
1
19
SCREW
6
52
PLATE ASSY
1
20
COVER COMPONENTS
1
53
SCREW
8
21
LEADING PLATE
1
54
RAM CONNECTOR ASSY
2
22
LEADING PLATE
2
55
HOSE CONNECTOR ASSY
2
23
WHEEL
2
56
HOSE ASSY
1
24
SUPPORTS
1
57
FRAME FOR PUMP
1
25
CUP
5
58
CLIP
2
26
CLIP
12
59
WHEEL
2
27
PIN
2
60
LOCK WASHER
2
28
SUPPORTS
1
61
HANDLE SLEEVE
1
29
SAFTY BAR
1
62
CONTRAL BOX
1
30
SPRING
1
63
INCHING SWITCH
1
31
ACTIVE HINGE
1
64
URGENT STOP SWITCH
1
32
R-PIN
2
65
ELECTRIC MOTOR
1
33
PIN
2
66
HANDLE SLEEVE
1
67
WASHER
2