Redliro JK1608P Operating manual

MODEL
JK1608P
REDLIRO TREADMILL
PRODUCT USE GUIDE

Service
Safety Information
Product Specications
Package List
Product Structure
Introduction to Display
Remote Control Instructions
Battery Replacement
Instructions for Using the Treadmill
Preparation before use
Instructions for Use
Product Maintenance
Daily Cleaning
Routine Maintenance
Troubleshooting and Handling
Workout Guide
Warranty
SERVICE
Thank you for purchasing this Redliro product. Questions, problems,
missing parts? Before returning to your retailer, contact our Customer
Service Department to receive more complete service, please email
your order number to: [e-mail]
Response
Time
URL : www.redliro.com
FOR INFORMATION REGARDING WARRANTY, REPLACEMENT PARTS, AND REFUNDS,
PLEASE CONTACT OUR CUSTOMER SUPPORT.
Emailing us with the information above will be the best
method to receive a response during peak business hours.
CONTENT
2
4
5
6
7
8
9
12
13
13
13
17
17
18
20
24
25

[email protected] [email protected]
45
SAFETY INFORMATION
TO REDUCE THE RISK OF INJURY, PLEASE READ INSTRUCTIONS IN FULL BEFORE USE.
• Intended for at-home use only. Please only use in an area with 3 - 6 feet of free space around your device.
Do not operate your device on a carpet more than 0.5 inches thick or near water.
• Treadmill is not intended for use by children or those with physical, sensory, or cognitive impairments.
• To avoid injury, do not disassemble this machine without guidance of manufacturer.
• This product only works with electrical outlets with a voltage between 100 and 120VAC. If your product’s
plug does not t your home’s outlets, do not attempt to use.
• Check all parts before use to ensure the screws and nuts are not loose.
• Keep ngers away from moving parts. Don’t put your hands or feet in the space under the running belt.
Keep children or pets away from the treadmill.
• Wear appropriate exercise clothes and athletic shoes while using the treadmill. Loose tting or oversized
clothing can get caught in machine.
• Unstable power supply may overload the circuit. Do not plug high-power devices such as a computer into
an outlet on the same circuit.
• This product can only be used by one person at a time.
• Do not place any objects on the machine. Do not stand directly on the belt when the machine is turned on.
• Keep children, pets, and household objects clear of the machine when folding and unfolding. Do not start
the machine when it is folded.
• Always unplug the power cord after use before cleaning and performing maintenance.
• Only use manufacturer’s accessories. Never exceed product’s maximum weight capacity of 300 lbs. (136kg)
• Moisture and overheating will a󰀨ect the use of the product. Please keep the machine, motor, power cord
and plug away from water and high temperatures.
• If the treadmill overheats, emits smoke or a burning smell during use, please stop using it immediately and
contact customer service for replacement.
• The company is not responsible for any harm caused by improper use.
PRODUCT SPECIFICATIONS
Product configuration Technical parameters
Input voltage 110V
Speed range 0.5-4 mph
Maximum load bearing 300 lbs
Package size 54.3 x 24.6 x 6.5 inches
Assembly size 51 x 20.5 x 6 inches
Operating area 41x15.5 inches
Rated power 2.25 hp
Net/gross weight 46.3/57.3lb

[email protected] [email protected]
67
PRODUCT STRUCTURE
SERIAL NO. DESCRIPTION Q U A N T I T Y UNIT
1TREADMILL 1 PC
2POWER CORD (THREE-PINPLUG) 1 PC
3SILICONE LUBRICANT 1 PC
4L STYLE WRENCH 1 PC
5REMOTE CONTROL 1 PC
PACKAGE LIST
TREADMILL × 1
REMOTE CONTROL × 1SILICONE LUBRICANT × 1POWER CORD
(THREE-PINPLUG) × 1
L STYLE WRENCH × 1
Display Panel
Motor Lower Cover
Power Switch
Motor Upper Cover
Running Belt
Foot Edge Strip
NOTE: THE RUNNING BELT IS MADE OF HEAD AND TAIL SPLICING, THERE ARE
SEAM MARKS, IT IS NORMAL PROCESS PHENOMENON, AND DOES NOT AFFECT THE
NORMAL USE OF THE TREADMILL.

[email protected] [email protected]
89
INTRODUCTION TO DISPLAY
1. The “TIME” window has two display modes.
• Standard mode counts from 00:00 ~ 99:00 and resets to 0 when it reaches 99:00.
• The preset/custom mode allows user to set a time for length of use. Select from 5 minutes to 99 minutes.
Once countdown has reached 0, your device will slowly stop and enter standby mode.
2. The "CALORIES" window has two display modes.
• Standard mode counts from 0 to 999.9, and resets to 0 when it reaches 999.9.
• The preset/custom mode allows user to set calorie value. Select from20 to 990. Once countdown has
reached 0, your device will slowly stop and enter standby mode.
3. The “STEP” window displays the number of steps taken. The count is 0~9999 steps. When the step count
reaches 9999, it will reset to 0.
4. The "SPEED" window displays the current running speed, and the speed range is 0.5mph~4mph.
• In preset mode, 12 preset schemes (P1 ~ P12) are displayed.
5. The "Distance" window has two display modes.
• In standard mode, the distance will increase from 0.0 to 99 miles, and the count will reset to 0 when it
reaches 99
• In preset/custom mode, the distance will be reduced from the inputted data (setting range: 1~99 miles) to 0.
When the display is 0, your device will slowly stop and enter the standby state.
1 2 4 35
REMOTE CONTROL INSTRUCTIONS
HOW TO ESTABLISH A NEW CONNECTION
1. Ensure the treadmill is connected to the power source but keep it powered on.
2. Hold the Mute button and Reset buttons on the remote control simultaneously for 5 seconds. The light on
the remote control will ash as it enters pairing mode.
3. The remote control will pair with treadmill automatically after a few seconds.
Increase Speed
Mode
ResetMute
Start / Stop Reduce Speed
Programs
NOTE: TO USE THE REMOTE CONTROL, YOU MUST FIRST ESTABLISH A NEW CONNECTION

[email protected] [email protected]
10 11
Start/Stop button:
Press Start/Stop button in standby mode and the treadmill will start after 3 seconds. The default speed is 0.5
mph.
Press Start/Stop button in preset/custom mode and the treadmill will start immediately, running at preset
values. It will immediately begin accumulating data.
Press Stop button while running belt is in motion and the treadmill will slow down slowly and return to pause
mode.
In the pause mode, press Start button and the running belt will begin moving at the previous selected
program.
+/- button:
Used for speed adjustment while your device is in use. Speed will be adjusted 0.1 mph each time you press.
Hold for more than 0.5 seconds and the speed will continue to increase or decrease. Can also be used to
adjust settings in preset/custom mode.
M button:
Press the M button while in standby mode to switch to custom mode. Select between time setting (setting
range 5:00 ~ 99:00), distance setting (setting range1 ~ 99 miles ) and calorie setting( setting range 20 ~ 990 ).
Press M button to change the cyclic display or xed display mode when in use.
Mute button:
Press the "Mute" button once to mute noise. Press it twice to cancel the operation.
Reset button:
In the pause mode, press Reset button and the running belt will slowly return to standby mode
P button:
In standby mode, the P button is used to select 12 preset automatic programs (P01 ~ P12)
FUNCTION OF THE REMOTE CONTROL
TIME
PROGRAMA
SET TIME/20=RUNNING TIME FOR EACH SECTION
P1 SPEED 1.0 2.0 3.0 4.0 4.0 3.0 4.0 4.0 4.0 3.0 4.0 4.0 4.0 4.0 4.0 2.0 3.0 4.0 3.0 2.0
P2 SPEED 1.0 3.0 4.0 4.0 4.0 2.0 4.0 2.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 2.0 4.0 4.0 3.0 2.0
P3 SPEED 1.0 4.0 4.0 1.0 4.0 4.0 1.0 4.0 4.0 4.0 4.0 2.0 4.0 4.0 1.0 2.0 4.0 3.0 3.0 2.0
P4 SPEED 1.0 4.0 2.0 2.0 2.0 4.0 2.0 4.0 4.0 2.0 2.0 3.0 4.0 1.0 2.0 4.0 4.0 4.0 4.0 2.0
P5 SPEED 1.0 3.0 4.0 3.0 4.0 4.0 3.0 1.0 2.0 4.0 4.0 4.0 4.0 2.0 3.0 4.0 1.0 4.0 4.0 3.0
P6 SPEED 1.0 2.0 2.0 4.0 3.0 1.0 4.0 2.0 3.0 2.0 1.0 4.0 2.0 3.0 4.0 1.0 2.0 4.0 1.0 3.0
P7 SPEED 1.0 4.0 4.0 4.0 4.0 2.0 4.0 3.0 4.0 4.0 1.0 2.0 3.0 4.0 1.0 2.0 3.0 4.0 2.0 3.0
P8 SPEED 1.0 4.0 4.0 4.0 4.0 3.0 1.0 4.0 4.0 4.0 1.0 3.0 4.0 4.0 2.0 3.0 4.0 4.0 3.0 3.0
P9 SPEED 1.0 2.0 3.0 1.0 2.0 4.0 2.0 1.0 1.0 2.0 1.0 4.0 1.0 2.0 3.0 4.0 2.0 4.0 4.0 3.0
P10 SPEED 1.0 3.0 3.0 4.0 4.0 4.0 3.0 4.0 2.0 4.0 1.0 4.0 4.0 3.0 4.0 4.0 4.0 4.0 4.0 4.0
P11 SPEED 1.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 3.0 3.0 1.0 2.0 4.0 4.0 4.0 4.0 4.0 4.0 2.0 2.0
P12 SPEED 1.0 4.0 4.0 4.0 2.0 4.0 4.0 4.0 4.0 4.0 1.0 4.0 4.0 4.0 4.0 2.0 4.0 4.0 2.0 2.0
The 12 preset programs have the following speeds:

[email protected] [email protected]
12 13
Step 1: Push back to remove the cover and install the battery.
BATTERY REPLACEMENT
Step 2: Remove button cell of remote control:
After long-term use, the remote control will have reduced sensitivity or become inoperable due to insu󰀩cient
power, and the battery needs to be replaced. Remove battery cover and take dead batteries out of your
remote control.
Step 3: Install button cell of remote control:
Ensure you have purchased new batteries that are the right type for the remote control by comparing with the
dead ones. Insert your new batteries into the remote and replace cover. Dispose of old batteries responsibly.
1
1
2
2
3
3
INSTRUCTIONS FOR USING THE TREADMILL
PREPARATION BEFORE USE:
INSTRUCTIONS FOR USE
1. Plug in the power cord
2. Establish the connection between the treadmill and the remote control
3. Press the power switch on the treadmill and wait for the indicator light to turn on
Note: All modes of the treadmill must be started while the machine is in standby. Keep treadmill in standby
before switching to a di󰀨erent mode.
Note: In order to extend the life of treadmill, the maximum time for one workout has been set to 99 minutes.
The treadmill will stop running should you hit this time and the display screen will read END.
HOW TO USE THE TREADMILL IN STANDARD MODE
1. How to turn on the treadmill
In standby mode, press the Start/Stop button on the remote control and the running belt will begin moving at
0.5mph in 3 seconds
2. How to adjust the treadmill speed
To change the speed of the running belt, press the +/- buttons on the remote control; the speed will be
adjusted by 0.1mph when you press the button. Hold for 0.5 seconds or longer and the speed will increase or
decrease continuously.
3. How to select the desired display mode
The left screen displays three modes: Time, Step and Calorie. The right screen displays two modes: Speed
and Distance. When the treadmill is running, you can select xed display or cyclic display mode by pressing
the M button on the remote control. In cyclic display mode, the display between each option in 5 second
intervals.
4.How to pause/restart the treadmill
Press Start/Stop button on the remote control while running belt is in motion and the treadmill will slow down
slowly and return to pause mode.
In the pause mode, press Start/Stop button on the remote control and the running belt will begin moving at
the previous selected program.
5. How to turn o󰀨 the treadmill
When the treadmill is paused, press the Reset button on the remote control and the treadmill will slowly
return to standby mode.
123

[email protected] [email protected]
14 15
HOW TO USE THE TREADMILL IN PRESET MODE
1. How to choose a program
In standby mode, you can select from 12 preset automatic programs (P1-P12) by pressing the P button on
the remote control
2. How to adjust the time of the preset program
After you have selected a preset program, press the +/- buttons on the remote control to adjust its duration
in 1 minute increments. Hold for over 0.5 seconds for timer to roll quickly. The selectable time range is 5-99
minutes.
3. How to turn on the treadmill
When you have selected the desired automatic program and duration, press the Start/Stop button on the
remote control, and the running belt will begin moving at the preset program speed in 3 seconds
4.How to pause/restart the treadmill
Press the Start/Stop button on the remote control while running belt is in motion and the treadmill will slow
down slowly and return to pause mode.
In the pause mode, press the Start/Stop button on the remote control and the running belt will begin moving
at the previous selected program.
5. How to turn o󰀨 the treadmill
When the treadmill is paused, press the Reset button on the remote control and the treadmill will slowly
return to standby mode.
Note: The speed can’t be adjusted when running in preset mode
HOW TO USE THE TREADMILL IN CUSTOM MODE
1. How to choose a program
In standby mode, you can press the M button on the remote control to select a mode from time, distance and
calorie
2. How to set the value of the program
Note: Only one of the three modes can be selected.
Time setting:
In standby mode, press the M button on remote control and adjust time by pressing the +/- buttons to adjust
its duration in 1 minute increments. Hold for over 0.5 seconds for timer to roll quickly. The selectable time
range is 5-99 minutes.
Distance setting:
In standby mode, press the M button on the remote control twice and then adjust the distance by pressing the
+/- buttons on the remote control. Hold for more than 0.5 seconds for counter to roll quickly. The selectable
distance range is 1-99 miles.
Calorie setting:
In standby mode, press the M button on the remote control 3 times, and then adjust the number of calories
you wish to burn by pressing the +/- buttons. Adjustments made in units of 1 calories. Hold for more than
0.5 seconds for the value to increase or decrease continuously. The selectable calorie burn range is 20-990
calories.

[email protected] [email protected]
16 17
3. How to turn on the treadmill
Once you've set up your desired program, press the Start/Stop button on the remote control and the running
belt will begin moving at 0.5mph in 3 seconds
4. How to adjust the treadmill speed
To change the speed of the running belt, you can press the +/- buttons on the remote control. Pressing the
button once will adjust speed by 0.1 mph; holding the button will allow counter to roll quickly.
5.How to pause/restart the treadmill
Press the Start/Stop button on the remote control while running belt is in motion and the treadmill will slow
down slowly and return to pause mode.
In the pause mode, press the Start/Stop button on the remote control and the running belt will begin moving
at the previous selected program.
6. How to turn o󰀨 the treadmill
When the treadmill is paused, press the Reset button on the remote control and the treadmill will slowly
return to standby mode.
PRODUCT MAINTENANCE
REGULAR MAINTENANCE IS IMPORTANT FOR YOUR SAFETY AND TO EXTEND THE LIFE OF
YOUR PRODUCT. PLEASE CHECK AND TIGHTEN ALL PARTS BEFORE YOUR FIRST USE AND
REPLACE WORN PARTS OVER TIME AS NEEDED.
DAILY CLEANING
Clean your treadmill regularly. The running belt and console must be clean and dry for long term safe use.
Power o󰀨 and unplug your treadmill. Wipe the exterior with a damp cloth and a small amount of mild soap.
The display console must be kept dry, however; wipe it with a dry, soft towel.
Dry the treadmill thoroughly with a soft towel.
Note: Do not spray liquid directly on the treadmill. To avoid damaging the console, keep it dry at all
times.
BLUETOOTH PAIRING GUIDE
Please staying within range of your treadmill while you have your device to keep the connection
Pair your Bluetooth device with the treadmill by:
1.Turing your treadmill on
2.Make sure that Bluetooth is enabled on your device
3.On the pairing screen, nd your treadmill with name “Bluetooth”, select and connect it

[email protected] [email protected]
18 19
Use of Silicone Lubricant
The treadmill has been lubricated prior to shipment. Friction between the running belt and the running board
will greatly a󰀨ect the service life and performance of the product, so be sure to lubricate every 3 months or
100 miles of use.
The silicone oil bottle is sealed. If you need to use it, unscrew the cap and break the sealing lm of the bottle
Gently lift the running belt 2-3 inches to give yourself enough room to apply silicone lubricant to the surface
of the running board. Apply the lubricant in 4 - 6 inches strips on both sides of the board, ensuring that none
gets into the motor shaft, which can cause the belt to slip.
Start the treadmill and let it run for 3 minutes to distribute the silicone lubricant evenly.
Running Belt Adjustment
All treadmills are shipped with the running belt adjusted in place of immediate use.
The running belt may deviate from its ideal position over time, which can be caused by the following.
1. The main body is not in kept in a stable position.
2. The user's feet are not in the center of the running belt.
3. The user's feet exert uneven force.
If the deviation is due to issues 2 and 3 above, the treadmill can be returned to normal after 3 minutes of
rotation with no weight on the running belt .
If the above does not solve the problem, adjust the running belt with the L-Wrench.
ROUTINE MAINTENANCE
Running belt is loose
Note: Please unplug the power cord.
The running belt will loosen over time. A loose running belt will not function properly.
Then plug in the power cord, run the treadmill for 3 minutes. Repeat until the running belt is centered.
Running belt is o󰀨 center
Note: Please unplug the power cord.
Running belt shifted to the left
Use the L-Wrench wrench to turn the left rear roller bolt clockwise 1/4 of a turn to tighten the running belt.
Running belt shifted to the right
Use the L-Wrench to turn the right rear roller bolt clockwise 1/4 of a turn to tighten the running belt.
Then plug in the power cord, and run the treadmill for 3 minutes. Repeat until the running belt is centered.
Note: use of your treadmill with the running belt out of place can cause preventable wear with the
potential for injury.
Note: A running belt that is too tight can cause damage to the belt itself and its rollers. Strange
noises are an indication your belt is too tight and must be loosened for a safe experience.
Note: Search “REDLIRO” on YouTube to nd videos on how to adjust the running belt.