REDT Miracle-A6 User manual

- 1 -
MIRACLE-A6
CAUTION
☞Be careful not to mount a key incorrectly (asshown in the following figures)
when cutting or decoding.
Standard(Edge) Key:
Laser Key:

- 2 -
MIRACLE-A6
Table of Contents
◆Cautions
- 4
◆Parts
- 7
◆Parts Names
- 9
◆Specifications
- 10
◆Key Pad
- 11
◆Cutter
- 12
◆Decoder
- 13
◆Spindle Belt
- 15
◆Type of Clamps
Clamp Type
How to Replace the Clamp
How to Adjust Clamp Holding Lever Position
How to Use the Another Clamps
◆How to Fasten Keys by Clamp Types
Automobile key Clamp (No.1 Clamp)
Dimple key Clamp (No.2 Clamp)
Single Sided Key Clamp (No.3 Clamp)
- 20
◆How to Use Auxiliary Key Hold Bracket Set
- 30
◆How to Use Tibbe Clamp
- 31
◆How to Use LDV(FO19) Clamp
- 32
◆How to Use SX9 Key Clamp
- 33
◆Clamp Origin Setting
Auto Setting
Manual Setting
- 34
◆Key Cutting Procedure
Standard Key
Laser Key
Cut Key by using IC Card number
IC Card is...
- 38
◆Search for Use the Key Type
- 44
◆Original Key Copy
- 45
◆Key Cut Option
- 47
◆Half Cut Method
- 48

- 3 -
MIRACLE-A6
Code Master Program
◆Program Installation
- 50
◆Connecting to the Computer and Running the
Program
Bluetooth wireless connection
USB cable connection
Portal to Miracle Program
- 51
◆Basic Menu
Automobile Key
Motorcycle Key
Standard Key (Domestic Key)
Key Blank Search
- 53
◆Convenient Features
Previous Key Data View
Key Cut List
Favorite
Customer information
- 59
◆Key Cutting Procedure
Standard Key
Laser Key
- 62
◆Original Key Copy
- 65
◆Key Cut Option
Speed Setting
Auto Key Measurement
Multi-Stage Cutting Count
Trim
Stop
Clamp Reference Point Change
- 67
◆Key Data Load Screen
Bitting Input
Read/Copy Original Key
Key Cutting
Menu
- 71

- 4 -
MIRACLE-A6
Make sure to follow the below directions when you use the machine.
Miracle-A6 is designed to be operated DC24V. This machine is only to be
operated made when DC24V is available. When any power supply other
than DC24V is used, the machine may not function properly In particular,
when low voltage (less than 24V) is used, the DC motor output decreases,
leading to slower rotation.
Replace the Cutter on a regular maintenance basis. Delaying the
replacement of the Cutter may inhibit the cutting force, leading to failure of
accurate key cutting.
Depending on the alloy makeup of the key blank, the necessary cutting force
of the Cutter should be adjusted. Set the cutting speed and cutting unit by
the strength of the key blank.
Take precautions not to drop the machine or allow it to get wet (from rain or
snow) when using it outside.
Make sure to check for errors on the key blank before cutting the key. An
error on key blank itself may produce unexpected results, even if the
machine cuts the key accurately.
This machine is not equipped with a function to sense the Clamp contact to
the tools. Therefore, when key cutting, the Clamp may be damaged by the
tools, depending on the type of the key or the type of the Clamp selected.
Take precautions when operating the key and the Clamp. The manufacturers
or resellers are not responsible for Clamp damage during the key cutting
process.
◆Data and Firmware Upgrade
- 79

- 5 -
MIRACLE-A6
Cautions for Safety
Make sure to observe the followings for safe use of the product.
 The below information is provided for user safety and to prevent personal injury or property damage.
Read the below cautions carefully.
Indicates that you may get injured or experience equipment damage if you fail to follow the
instructions.
Indicates that you could be seriously injured if you fail to follow the instructions.
Cautions for Power
Never use damaged or defective power
cords or loose plugs or sockets.
They may cause electric shock or
fire.
Never plug too many power cords into
an outlet simultaneously. The outlet
may get too hot and cause fire.
Never pull the plug out by tugging on
the power-cord, or touching the power
plug.
Keep the machine unplugged not using
it for a long time.
If smoke rises up while using the
machine, turn off the power right away.
Contact user`s dealer or our factory
for advice.
Cigarette jack fuse may blow out when
you connect the machine to the vehicle
cigarette jack. In such a case, replace
the old fuse with a new fuse 10A or
greater. You can only use the machine
connected to the cigar jack while the
vehicle engine is running.
Cautions for Installation
Do not install the machine in a place
with oil, smog, moisture, dust or water
splashing.
It may cause electric shock or fire.
Do not put burning cigarettes or
candles on the machine. Keep it away
from heating apparatus such as
stoves.
The unit could get overheated,
resulting in failure or fire.
Make sure to install the main body on
a stable flat surface.
The machine weighs about 21.5Kg and
generates vibration on both sides
during operation. If you use the
machine on a weak, wobbly, or bumpy
surface, it may lead to damage on
machine/worktable or injury

- 6 -
MIRACLE-A6
Cautions for Use
The blade of the machine spins at
high speed during its operation. Be
careful not to allow any part of user’s
body or clothing to get inside the
machine.
The operator may get seriously
injured by the Cutter if this is ignored
or overlooked.
Do not put any tools, water containers,
mugs, cups or small metal pieces on
the unit or cutting bed.
The vibration of the machine and
carelessness of the user may
cause falling of the above objects,
which could lead to bodily injury.
Overheating or electric leakage
could also lead to fire or
malfunction.
It may also cause electric shock or
fire when the unit gets wet.
Be careful not to catch any part of user`s
body or clothing in the route of each axis
of the machine, so as not to be damaged
or injured by its blade.
When a part of body or object is jammed
in the axis path of the machine, or gets
scratched by a sharp blade, serious
injury, machine damage or mechanical
failure may occur.
Other Cautions
Do not disassemble or remodel the body
of the machine.
It may cause fire, electric shock or
equipment failure. If you need a
check-up, adjustment, or machine
repair, please ask user`s dealer for
service or contactor factory.
Curiosity or carelessness of young
children about the machine may lead
them to serious injury. Keep the
machine out of reach of small children.
In winter, sub-zero temperatures, may
cause the unit to be unable to work
properly. If such thing happens, increase
the temperature of the work
environment. Do not let the machine
room temperature go below 0 degrees
(C)

- 7 -
MIRACLE-A6
Contents
Figure
Quantity
Purpose
AC adapter
(CP-04)
1 EA
Power supply
24VDC 5A
Power cable
(CP-02)
1 EA
Cutter
(T60-E20)
2 EA
Tool for key cutting
Decoder
(T60-P10)
2 EA
Tool for decoding
T Wrench
(CP-T25)
1 EA
Tool change
M5 bolt
(CP-95)
2 EA
Used to fasten Cutter or Decoder
Stopper
(CP-91)
1 EA
Guide for Key positions
Stopper
Right-to-Left
(CP-96)
1 EA
Guide for alignment-key location
to hold a key from right-to-left
Parts

- 8 -
MIRACLE-A6
Auxiliary key hold
bracket set
(SX9 Clamp)
(CP-92)
1 SET
5 EA
Auxiliary bracket to hold double-sided
standard keys more firmly
Spindle belt
(CP-SB35)
6 EA
Spindle belt transmitting spindle motor
power to spindle
(G35 3mm thick, 35mm in diameter)
Tools rack
(CP-98)
1 EA
Tools storage
Mounting bracket
(BP-95)
2 EA
Bracket to Hold
the product on floor
Back bracket
(BP-94BMA9)
1 EA
Bracket to protect the power connector
and USB port
Calibration bar
1 EA
Guide for the calibration of
the automobile key Clamp and dimple key
Clamp
Program CD
1 EA
“CodeMASTER” program CD
( SW for car key cutting and update)
User manual
1 EA
Product instruction guide
USB Communication
Cable
1 EA
Connecting the product to PC
for communication
☞TIP)
Cutters and spindle belts are consumables. Make sure to replace them with the new one on a regular
maintenance schedule.

- 9 -
MIRACLE-A6
Key
Front Shield Cover
Power Switch
(Emergency Switch)
LED Light
Clamp
Clamp Knob
Chip Tray
Spindle
Decoder
LCD
Parts Names
Power Port
12V DC
USB Communication
Port
Clamp Holding Lever
Tool box

- 10 -
MIRACLE-A6
Power Input
24VDC / 5A
Power Consumption
120W
Dimensions
255 (W)×360 (H)×340 (D)mm
Weight
24kg
Resolution
XYAxis: 0.005mm, Z Axis: 0.00125mm
Spindle Revolution
8,750 rpm
Bluetooth
Spec.
Bluetooth Specification V1.2
Frequency
2.4GHz ISM Band
Profile
SPP, GAP
Temperature
0 - 40 ºC
Humidity
10 - 90 %
Usage
Cutting and duplicating keys
Specifications

- 11 -
MIRACLE-A6
Menu: Selects menu item
Input Number: Inputs bitting number
Inputting number 1~5: Press the button.
Inputting number 6~0: Press the button again when 1~5 is displayed.
Menu: Moves back
Input Bitting: Inputs decimal
Menu:
: Moves to previous/next menu page
: Moves menu item selection
Input Number:
: Moves to next input position
: Increase/Decrease number
[Load key by Instacode]
Load key data by IC Card Code number in Instacode.
[Retrieve key by Maker]
Load key data from maker list.
[ENTER]
Enters selection or starts action.
[MENU]
Goes into menu
[TOOL CHANGE]
Measures cutter or decoder length
[STOP]
While cutting: Cancel cutting
Menu: Jump to start
Key Pad

- 12 -
MIRACLE-A6
The Cutter is a tool to be used for cutting a Key. The range of Cutter thickness can be set
between 1.5mm -2.5mm. 2.0mm is the default thickness of the Cutter.
[How to Replace]
1.
Loosen the bolt with a T-wrench to replace the Cutter.
2.
Press the [Tool Change] button in the
keypad.
3.
If you press the [Enter], the length of Cutter is
Automatically measured.
☞TIP)
If the key is not cut accurately or there is a loud noise in cutting, check the Cutter condition and
replace it if necessary.
Type
Flat Cutter (T60-E20)
Total length
40mm
Shank Diameter
6mm
Blade Diameter
2.0mm (recommended)
Cutter

- 13 -
MIRACLE-A6
The Decoder is a tool used for decoding and copying keys.
[How to Replace]
1.
Loosen the bolt with a T-wrench to replace the
Decoder.
2.
Press the [Tool Change] button in the
keypad.
3.
If you press the [Enter], the length of Decoder
is Automatically measured.
Type
Decoder (T60-P10)
Total length
40mm
Shank
Diameter
6mm
Blade Diameter
1.0mm
Decoder

- 14 -
MIRACLE-A6
The Decoder is easily broken.
If the Decoder is bent, a measurement error is generated. The machine is designed so that
when the force is strong enough to bend the Decoder, the Decoder will break off.
Take extra care not to drop Decoder, to impact to the Decoder nor make mistakes
when using it.
The manufacturer of resellers are not responsible for the breaking of Decoder, in
any cases.

- 15 -
MIRACLE-A6
Miracle-A6 delivers rotational force to the Spindle through the Spindle Belt.
The Spindle Belt is perishable. If the key does not cut accurately or there is a loud noise
in cutting, check the spindle belt condition and replace it if necessary.
[How to Replace]
- Loosen the bolts on the head cover to remove the Cover and remove the existing Belt and replace it with the new
Belt.
When the Spindle Belt wears out, the Cutter life is reduced and key cutting may not function
properly.
Check the Spindle Belt condition periodically and replace if necessary.
Type
Silicon Belt (CP-SB35)
Thickness
3mm
Diameter(Inside)
35mm
Spindle Belt
be Replacement

- 16 -
MIRACLE-A6
Miracle-A6 can be used by exchanging three types of clamps according to the type of
keys to be processed.
[Clamp Type]
1) Automobile key (CP-86)
No.1 Clamp
2) Dimple key (CP-88)
No.2 Clamp
3) Single Sided key (CP-89)
No.3 Clamp
Type of Clamps

- 17 -
MIRACLE-A6
[How to Replace the Clamp]
1. Unfasten the Clamp holding Lever.
2. Remove the Clamp.
3. Push the desired Clamp into the groove. Turn it in as far as possible and fasten the holding Lever.
☞TIP)
If the Clamp holding Lever is located in a position that prevents you from fastening the Clamp, you can
adjust the Lever position.

- 18 -
MIRACLE-A6
[How to Adjust Clamp Holding Lever Position]
1. Pull out the Clamp holding Lever.
2. To pull it out, turn it counterclockwise.
3. Push it into the original position, turning clockwise.
If you fasten the Clamp by pressing down the Lever repeatedly, the Clamp may wobble. The
Clamp must be tightened by turning the Lever.
DON’T Press Down
DO Turn Clamp

- 19 -
MIRACLE-A6
[How to Use the Another Clamps]
- When cutting and copying keys, press [MENU] button from the key fixing screen to choose a clamp.
Laser Key
Standard Key
Dimple key (CP-88)
Single Sided key (CP-89)