Reece MILLI User manual

MILLI
EDGE MIRROR WITH CLOCK
SPECIFICATIONS
Recommended use Domestic, hotel and commercial.
Features Digital clock
Infrared on/off sensor
LED dimmer
5mm glass with PVC safety backing
Defogger function
Electrical 240V AC / 50Hz / 35W / IP44
CLEANING RECOMMENDATIONS
We recommend the use of a soft dry cloth.
This product should not be cleaned with abrasive materials or cleaning agents.
Damage caused by improper treatment is not covered by the product warranty - refer to warranty conditions.
To see the complete MILLI range go to
www.reece.com.au/bathrooms
page 1 of 4
Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered
trades people. The manufacturer/distributor reserves the right to vary specifications or delete models from
their range without prior notification. Dimensions are nominal measurements only. Dimensions and set-
outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility
for printing errors.
Tech Page Version 2

MILLI
EDGE MIRROR WITH CLOCK
page 2 of 4
Please ensure a copy of the installation instructions is left
with the end user for future reference
WARNING
This mirror must be installed by a qualified electrician in accordance with AS/NZS 3000 wiring rules. Switch off the electrical
supply at the mains before installation and maintenance. A means of disconnection must be incorporated in the fixed wiring
in accordance with the wiring rules. Suitable for bathroom zones 2, 3, and non-bathroom/dry areas. See diagram below. Not
suitable for above baths (zone 0) or zone 1, nor for installation in saunas, steam rooms or shower cubicles.
Do not connect to a plug and socket outlet. Rated IP44 and suitable for indoor use only. Do not fix to damp or conductive
surfaces. Site well away from curtains and fabrics. Never cover the mirror. Switch off after use. Do not leave on for prolonged
periods. This appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been given supervision or instruction. Children should be supervised to
ensure that they do not play with the appliance.
IMPORTANT!
Inspect the product immediately upon receipt for transit damage, missing parts or manufacturing faults. Handle the product with
care and protect against knocks to all sides and edges of the glass.

MILLI
EDGE MIRROR WITH CLOCK
page 3 of 4
Please ensure a copy of the installation instructions is left
with the end user for future reference
INSTALLATION INSTRUCTIONS
1. Remove screws from mirror casing as indicated.
2. Separate mirror from casing.
3. Disconnect internal wiring.
4. Use mirror casing to mark fixing points.
5. Drill wall as per markings from step 4
6. Insert wall plugs
7. Feed electrical wiring through rear of mirror casing
and fix casing to wall
8. Complete all required electrical connections and
reattach mirror to casing
9. Re-insert screws and ensure that the mirror is
securely fixed to its casing

MILLI
EDGE MIRROR WITH CLOCK
page 4 of 4
Please ensure a copy of the installation instructions is left
with the end user for future reference
OPERATION
Infrared mirror light on /off sensor
Moving your hand in proximity of the sensor turns the mirror light on and off.
When turning on the lights, if you keep your hand in front of the sensor, after a few seconds, the LED intensity will change.
Once the desired intensity is reached, move your hand away from the sensor and the mirror will save that particular intensity.
The next time the mirror is turned on it will return to the programmed intensity.
Please note, that the mirror must be installed not less than 70mm from the wall or bathroom furniture column, otherwise the
sensor will read the object and will not function properly.
Defogger on off switch
The defogger is switched on and off with a toggle switch, mounted on the side of the mirror, which is illuminated red when the
defogger is operating.
ON / OFF DEFOGGER
Setting the clock
NOTE: It is normal for top and bottom LED to have partial illumination even in the off position due to small current
through the IR on /off switch.