Reed Instruments R3000SD User manual
Data Logging
pH/ORP Meter
Instruction
Manual
R3000SD
REED Instruments
2
Table of Contents
Introduction ................................................................................................ 3
Product Quality........................................................................................... 3
Safety ......................................................................................................... 4
Features...................................................................................................... 4
Included...................................................................................................... 4
Specications..........................................................................................4-5
Instrument Description............................................................................... 6
Display Description .................................................................................... 7
Operating Instructions...........................................................................8-10
Power ON/OFF ...................................................................................... 8
pH or ORP Modes.................................................................................. 8
pH Measurement Mode (Manual Temperature Compensation) ............. 8
pH Measurement Mode (Automatic Temperature Compensation) ........ 9
mV Measurement Mode......................................................................... 9
Data Hold ............................................................................................... 9
Recording Maximum and Minimum Readings..................................9-10
Backlight .............................................................................................. 10
Setup Mode.........................................................................................10-14
Formatting the SD Card (Sd F)........................................................... 11
Setting the Time and Date (dAtE)....................................................... 11
Setting the Data Logging Sampling Rate (SP-t) ................................. 12
Enabling/Disabling Auto Power Off (PoFF)......................................... 12
Enabling/Disabling the Beeper (bEEP) ............................................... 12
Setting Data Decimal Format (dEC).................................................... 13
Selecting the Temperature Unit of Measure (t-CF)............................. 13
Setting pH manual Temperature Compensation Value....................... 13
ESC .................................................................................................... 14
Verify Set Time and Date.................................................................... 14
Verify Sampling Rate .......................................................................... 14
continued...
REED Instruments
3
Data Logging.......................................................................................14-16
Data Recording Modes....................................................................... 14
Manual Data Logging Mode ..........................................................14-15
Automatic Data Logging..................................................................... 15
Transferring Data from the SD Memory Card to a Computer........15-16
pH Calibration .....................................................................................16-17
Required Equipment for Calibration................................................... 16
Calibration Procedure ...................................................................16-17
Clearing pH Calibration Data.............................................................. 17
Data Stream Output ................................................................................. 18
3.5mm Terminal to RS-232 Serial Connection ................................... 18
System Reset ........................................................................................... 19
Battery Replacement................................................................................ 19
Applications.............................................................................................. 19
Accessories and Replacement Parts ..................................................19-20
Frequently Asked Questions (FAQ's)........................................................ 20
Product Care ............................................................................................ 21
Product Warranty ..................................................................................... 21
Product Disposal and Recycling .............................................................. 21
Product Support....................................................................................... 22
Introduction
Thank you for purchasing your REED R3000SD Data Logging pH/ORP
Meter. Please read the following instructions carefully before using your
instrument. By following the steps outlined in this manual your meter will
provide years of reliable service.
Product Quality
This product has been manufactured in an ISO9001 facility and has been
calibrated during the manufacturing process to meet the stated product
specications. If a certicate of calibration is required please contact the
nearest authorized REED distributor or authorized Service Center. Please
note an additional fee for this service will apply.
REED Instruments
4
Safety
Never attempt to repair or modify your instrument. Dismantling your
product, other than for the purpose of replacing batteries, may cause
damage that will not be covered under the manufacturer's warranty.
Servicing should only be provided by an authorized service center.
Features
probe, R3000SD-ATC)
Included
Specifications
Temperature
Automatic Temperature
Compensation (ATC): Manual: 33.8 to 212°F (1 to 100°C)
Optional ATC Probe (R3000SD-ATC):
32 to 149°F (0 to 65°C)
ORP (mV)
Measuring Range: -1999 to 1999mV
Accuracy: ±(0.5% +2 dgt)
Resolution: 1 mV
continued...
REED Instruments
5
pH
Measuring Range: 0.00 to 14.00
Accuracy: ±(0.02 pH +2 dgt)
Resolution: 0.01 pH
pH Electrode Compatibility: Any pH electrode with BNC connector
General Specifications
Display: Dual Display, LCD
Backlit Display: Yes
Data Hold: Yes
Min: Yes
Datalogging Capabilities: Yes
Real-Time Clock and
Date Stamp: Yes
Sampling Rate: Yes (1 second to 8 hours, 59 minutes
and 59 seconds)
with SD card (optional)
Auto Shut-off: Yes (after 10 minutes/off)
Kick Stand: Yes
Tripod Mountable: Yes
Low Battery Indicator: Yes
(optional)
Data Output: Yes (RS-232)
Battery Life: Sampling Time Dependent
Product Certications: CE
Operating Temperature: 32 to 122°F (0 to 50°C)
Storage Temperature: 14 to 140°F (-10 to 60°C)
Operating Humidity Range: 10 to 80%
Weight: 1.1lb (489g)
REED Instruments
6
Instrument Description
pH/ORP Meter
SD Series Data logger
TIME
LOG/SET
SAMPLING
CHECK
FUNCTION
POWER
HOLD
ESC
REC
ENTER
R3000SD
2
3
4
6
5
AB
7
8
9
10
11
12
13
14
1
15
16 17
1. LCD Display
2. POWER/Backlight Button
4. TIME Button
5. SD Card Slot
6. HOLD/ESC Button
7. REC/ENTER Button
8. Down/ Button
9. /SET/
CHECK Button
10. RS-232 Output Jack
11. Reset Pin
12. Power Adapter Input Jack
13. Tripod Mounting Screw
14. Battery Cover
15. Kickstand
16. pH/ORP Electrode Input
(BNC) Jack
17. Temperature Probe Input Jack
REED Instruments
7
Display Description
3
6
10
1. pH/ORP (mV) Measurement Reading
2. Date & Time Values/Temperature Measurement Reading
3. Date/Time Stamp
4. Data Logging Status Indicator
5. SD Card Status Indicator
8. Record Mode Indicator
9. Data Hold Indicator
10. Low Battery Indicator
REED Instruments
8
Operating Instructions
Prior to first use with the meter, the pH electrode should
be calibrated. Refer to the pH Calibration section
of this manual for further instructions.
Power ON/OFF
Turn the meter on by pressing the POWER button. To turn the meter off,
press, hold and release the POWER button for 2 seconds.
Note:
adapter (sold separately).
pH or ORP Modes
This meter offers pH and ORP modes of measurement capable of
measuring 0.00 to 14.00 pH and 0 to 1999 mV (ORP).
pH measurements achieve better results when the temperature of the
solution being tested is known and a temperature compensation factor
is applied. This can be attained using manual or automatic temperature
compensation.
is not connected to the meter and the temperature of the solution under
test is manually entered. The temperature compensation value appears
on the lower part of the LCD display.
probe is connected to the meter (R3000SD-ATC) and inserted into
the solution under test. The temperature compensation value will also
appear on the lower part of the LCD display.
pH Measurement Mode (Manual Temperature Compensation)
1. Connect the Optional pH Electrode into the pH/ORP Input BNC Jack.
2. Press the FUNCTION button to select pH mode.
3. Set the pH Manual Temperature Compensation value. Refer to Setup
Mode for details.
4. Place the pH electrode into the measured solution, so that the tip of
the electrode and junction are fully immersed and stir at a moderate,
uniform rate. The top of the LCD will display the pH value while
the bottom part of the LCD will display the setting for the manual
temperature compensation value. continued...
REED Instruments
9
pH Measurement Mode (Automatic Temperature Compensation)
1.
Connect the optional temperature probe into the temperature input jack.
2. Connect the optional pH electrode into the pH/ORP input BNC jack.
3. Press the FUNCTION button to select pH mode.
4. Place both the temperature probe and pH electrode into the
measured solution, so that the tip of the electrode and junction are
fully immersed and stir at a moderate, uniform rate. The top of the
LCD will display the pH value while the bottom part of the LCD will
display the setting for the manual temperature compensation value.
Note: When measurements have been completed, be sure to store the pH
electrode in its protective cap.
mV Measurement Mode
This meter has a built in mV (millivolt) measurement function, which
the range of ±1999 mV.
1. Connect the Optional ORP Electrode into pH/ORP Input BNC Jack.
2. Press the FUNCTION button to select mV (ORP) mode.
3. The top of the LCD will display the mV value.
Data Hold
1. While taking a measurement, press the HOLD button to freeze the
current readings on the display.
2. While in this mode a HOLD symbol will appear.
3. Press the HOLD button again to resume normal operation.
NotePOWER
button are disabled.
Recording Maximum and Minimum Readings
1. Press the REC button to enter recording mode as indicated by
and minimum readings.
2. While in recording mode;
continued...
REED Instruments
10
A) Press the REC
B) Press the REC button again and the minimum value will appear
hold the REC button for two seconds.
When in recording mode the POWER button is disabled
and the meter cannot be turned off.
Backlight
After powering the meter ON, the LCD Backlight will turn on automatically.
Setup Mode
1. Press and hold the SET button for 2 seconds to enter Setup Mode.
2. Press the SET button continuously to scroll through the
following parameters.
Parameter Description
Sd F Format the SD memory card
dAtE Set the time and date
SP-t Set the data logging sampling rate
PoFF Enable or disable the auto-power off function
bEEP Turn the beeper on or off
dEC
t-CF Select the temperature unit of measure (°C or °F)
t-SEt Set pH manual Temp. compensation value, pH only
ESC
3. Once the appropriate parameter has been selected, follow the
instructions below.
Note: At any time, you can press the ESC
and resume normal operation.
continued...
REED Instruments
11
Formatting the SD Card (Sd F)
1.
Press the and
2. Press the ENTER button to conrm selection.
3. Press the ENTER button again to re-conrm.
4. The meter will format the SD card and automatically return to the
Setup menu when formatting is complete.
Note: At any time, you can press the ESC
and resume normal operation. It is recommended that new SD cards
should be formatted prior to rst use. If the formatting process fails or if
no card is inserted, the meter will display:
Setting the Time and Date (dAtE)
1. Press the and buttons
2. Press the ENTER button to conrm selection.
3. Repeat steps 1 and 2 for month, day, hour, minute and seconds as
indicated by (mm/dd/h/m/s).
4. Press the SET button to save the time stamp and jump to
Note: At any time, you can press the ESC
and resume normal operation. The internal clock will keep accurate time
when the meter is powered off. When new batteries are installed the clock
will have to be reset. continued...
REED Instruments
12
Setting the Data Logging Sampling Rate (SP-t)
only) up to 8 hours, 59 minutes and 59 seconds.
2. Press the and buttons to adjust the required sampling rate by
hours, minutes or seconds as indicated by (h/m/s).
3. Press the ENTER button to conrm each selection.
4. Press the SET button to save the selected sampling rate and jump to
Note: At any time, you can press the ESC
and resume normal operation.
Enabling/Disabling Auto Power Off (PoFF)
1.
Press the and buttons to select between ON (enabled) or OFF
(disabled). With the Auto Power OFF feature enabled, the meter will
automatically switch OFF after 10 minutes of inactivity to preserve
battery life.
2. Press the ENTER button to conrm selection.
3. Press the SET
Note: At any time, you can press the ESC
and resume normal operation.
Enabling/Disabling the Beeper (bEEP)
1.
Press the and buttons to select between ON (enabled) or
OFF (disabled).
2. Press the ENTER button to conrm selection.
3. Press the SET
Note: At any time, you can press the ESC
and resume normal operation.
continued...
REED Instruments
13
Setting Data Decimal Format (dEC)
Numeric formats vary in different countries. By default the meter is set to
bASIC mode where a decimal point is used to separate units, (i.e. 20.00).
The European format uses a comma (i.e. 20,00) to separate units. To
appears on the LCD.
1. Press the and buttons to select between bASIC and Euro.
2. Press the ENTER button to conrm selection.
3. Press the SET
Note: At any time, you can press the ESC
and resume normal operation.
Selecting the Temperature Unit of Measure (t-CF)
1. Press the and buttons to select between °C and °F.
2. Press the ENTER button to conrm selection.
3. Press the SET
Note: At any time, you can press the ESC
and resume normal operation.
Setting pH manual Temperature Compensation Value
Ph measurements are more accurate when the temperature of the solution
being tested is known. This can be achieved by applying a manual or
automatic temperature compensation factor to the measurement. Please follow
the steps below to manually set the pH temperature compensation value.
1. Press the and buttons to select the select the temperature of the
solution being tested in °C or °F. By default, the meters temperature
compensation factor is set to 25°C or 77°F.
2. Press the ENTER button to conrm selection.
3. Press the SET
Note: At any time, you can press the ESC
and resume normal operation.
continued...
REED Instruments
14
ESC
Press the SET
mode and resume normal operation.
Note: At any time, you can press the ESC
and resume normal operation.
Verify Set Time and Date
During normal operation, press the TIME button once to display the hour,
minute, seconds. Press the button again to display the year, month
and day.
Verify Sampling Rate
selected sampling rate.
Data Logging
Data Recording Modes
Manual Data Logging: Press the LOG button to manually log up to 99
readings on a SD memory card (see Manual Data Logging Mode for details).
Automatic Data Logging: Setup the meter parameters in order to
automatically log data on a SD memory card. The number of data points
is limited by the size of the memory card.
Note: It is recommended to use a class 4 SDHC memory card between
The card must be inserted with the label side facing the rear of the meter.
Manual Data Logging Mode
In manual mode, the LOG button is pressed to manually log a reading on
the inserted SD card at any time. In order to setup the meter for manual
data logging, follow steps 1 through 7 below.
2. Press the REC
3. Press the LOG button to enter manual data logging function as
continued...
REED Instruments
15
between 1 and 99).
5. Press the and buttons to select one of the 99 data memory
positions in which to record.
6. Press the LOG button again to save a reading to memory.
REC button
2 seconds to resume normal operation.
Automatic Data Logging Mode
In automatic mode the desired data logging sampling rate can be set
between 1 second to 8 hours, 59 minutes and 59 seconds prior to
recording. In order to setup the meter for automatic data logging, follow
steps 1 through 5 below.
1. Press the REC
2. Press the LOG button to enter automatic data logging function as
time a reading is stored.
4. To pause the data logging session press the LOG button and
LOG
button again.
5. To end the current data logging session, press and hold the REC
button for 2 seconds.
Transferring Data from the SD Memory Card to a Computer
1. While the meter is powered Off remove the SD memory card from the
SD card slot.
2. Insert the SD memory card into the computer.
Position Date Time Ch1_Value Ch2_Value
1 19-07-10 11:00:39 3.45 pH 25 Degree_C
2 19-07-10 11:00:43 3.45 pH 25 Degree_C
3 19-07-10 11:00:47 3.52 pH 25 Degree_C
4 19-07-10 11:00:51 3.48 pH 25 Degree_C
5 19-07-10 11:00:55 3.5 pH 25 Degree_C
6 19-07-10 11:00:59 3.46 pH 25 Degree_C
7 19-07-10 11:01:03 3.45 pH 25 Degree_C
8 19-07-10 11:01:07 3.56 pH 25 Degree_C
9 19-07-10 11:01:11 3.45 pH 25 Degree_C
10 19-07-10 11:01:15 3.45 pH 25 Degree_C
11 19-07-10 11:01:19 3.45 pH 25 Degree_C
12 19-07-10 11:01:23 14 pH 30 Degree_C continued...
REED Instruments
16
pH Calibration
This meter has been manufactured for use with a pH electrode that
generates 0mV at pH7.00 (177.4mV at pH4). If your pH electrode does not
meet stated specications or is being used for the rst time, calibration
procedures are necessary. Calibration also ensures accurate
measurements. It is always recommended to carry out a two point
calibration for better accuracy.
Required Equipment for Calibration
1. pH Electrode (See Accessories and Replacement Parts)
2.
pH Buffer Solutions (See Accessories and Replacement Parts)
Calibration Procedure
1. Prepare buffer solutions for calibration. It is recommended to start
with calibration buffer pH 7.00 pH, followed by either pH 4.00 or
the pH 4.00 and pH 7.00 buffer solutions when measurements are
be on the higher side of the pH scale.
2. Connect the optional pH electrode into the pH input jack
3. Turn the meter on by pressing the POWER button.
continued...
REED Instruments
17
4. Manually adjust the temperature compensation value to make it
same as the temperature value of the pH buffer solution. Refer to the
Setup Mode section of this manual for instructions. For automatic
temperature compensation, plug in the optional ATC probe.
5. Rinse the electrode with distilled water to remove any residual solution.
6. Place the electrode into the pH 7.00 buffer solution, so that the tip of
the electrode and junction are fully immersed in the buffer solution,
and stir at a moderate, uniform rate. If using an ATC probe, both
probes should be placed into the solution together.
7. When calibration has stabilized, a pH value will appear at the top of
the display.
8. Press and hold both the REC and HOLD buttons until the screen
of the screen and release to enter the calibration mode.
9. Press the and buttons to scroll to pH 7.00 or whichever screen
matches your buffer solution.
10. Press the Enter button to save your selection.
11. Repeat steps 5 through 10 for the pH 4.00 and pH 10.00 buffer solutions.
Clearing pH Calibration Data
1. While under normal, press and hold both the REC and HOLD
calibration mode.
2. Press the and buttons
3. Press the ENTER button to conrm and erase all calibration data.
4. The display will continuously blink while the calibration data is
being erased.
5. When complete, the meter will resume normal operation.
REED Instruments
18
Data Stream Output
and use the following setting to view the data stream.
Terminal Settings:
41050000000010 = Upper Value, +10 pH
Reading
Decimal Place 0-3
Positive (+) = 0, Negative (-) = 1
°C = 01, °F = 02, pH = 05, mV = 18
1 = Upper display value,
2 = Lower display value
4
41050000000010 = Valeur supérieure, +10 pH
Lecture
Position décimale 0-3
Positif (+) = 0, Negatif (-) = 1
4
1 = valeur d'affichage supérieure,
2 = valeur d'affichage inférieure
°C = 01, °F = 02, pH = 05, mV = 18
3.5mm Terminal to RS-232 Serial Connection
RS-232 Mono Jack
Pin 2 (RX)
Pin 4 (DTX)
Sleeve
Tip
REED Instruments
19
System Reset
If the meter becomes unresponsive or if the display freezes, the
Reset
pin
can be used to reset the instrument.
2. After pressing the
Reset
pin, power the meter back up by holding the
POWER button for 2 seconds.
3. If resetting the meter does not resolve the issue, please return the
meter to the nearest authorized REED distributor or authorized
Service Center for repair.
Battery Replacement
When the low battery icon appears on the LCD, the batteries must
be replaced.
1. Remove the two (2) Phillips screws on the back of the meter directly
located above the top of the kickstand.
2. Remove the battery cover.
4. Secure the battery cover with the two (2) Phillips screws.
Applications
REED Instruments
20
Accessories and Replacement Parts
R3000SD-PH1 Professional pH Electrode
R3000SD-PH2
R3000SD-ORP Professional ORP Electrode
R3000SD-ATC Automatic Temperature Compensation Probe
R1404 pH Buffer Solution, 4.01, 500ml
R1407 pH Buffer Solution, 7.0, 500ml
R1410 pH Buffer Solution, 10.0, 500ml
R1420 Electrode Storage Solution, 500ml
R1425 Electrode Cleaning Solution, 500ml
R1500 Tripod
RSD-ADP-NA Power Supply, 110V
RSD-ADP-EU Power Supply, 220V
CA-05A Soft Carrying Case
R8888
SD-4GB
RSD-16GB
Don't see your part listed here? For a complete list of all accessories and
replacement parts visit your product page on www.reedinstruments.com.
Frequently Asked Questions (FAQ's)
I cannot turn off my meter, do you know why?
Often times, the meter cannot be turned off because it is in recording
REC button before attempting to turn the meter off.
Can I set an alarm to go off at a specific temperature?
The meter does not have an alarm function.
continued...
REED Instruments
Table of contents
Other Reed Instruments Measuring Instrument manuals
Reed Instruments
Reed Instruments Smart R1610 User manual
Reed Instruments
Reed Instruments R3530 User manual
Reed Instruments
Reed Instruments R8070SD User manual
Reed Instruments
Reed Instruments SMART Series User manual
Reed Instruments
Reed Instruments R9920 User manual
Reed Instruments
Reed Instruments Smart Series User manual
Reed Instruments
Reed Instruments R5090 User manual
Reed Instruments
Reed Instruments R8140 User manual
Reed Instruments
Reed Instruments R8050 User manual
Reed Instruments
Reed Instruments R5065 User manual
Reed Instruments
Reed Instruments R9930 User manual
Reed Instruments
Reed Instruments R6013 User manual
Reed Instruments
Reed Instruments R7700 User manual
Reed Instruments
Reed Instruments LM-81HT User manual
Reed Instruments
Reed Instruments R6210 User manual
Reed Instruments
Reed Instruments R3525 User manual
Reed Instruments
Reed Instruments R8085 User manual
Reed Instruments
Reed Instruments R1620 User manual
Reed Instruments
Reed Instruments R1600 User manual
Reed Instruments
Reed Instruments R9910SD User manual
