Regalo 1350 User manual

www.regalo-baby.com
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100 / Burnsville, MN 55306, USA
866.272.5274 (U.S. only) or 952.435.1080
Made in China
4-in-1 Play Yard
Safety Gate
OWNER’S MANUAL MODEL: 1350, 1350DS, 1350B
• READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE.
• KEEP INSTRUCTIONS FOR FUTURE USE.

English 3
Before Using Product
Read and follow all instructions carefully to ensure that your gate and extensions are
properly installed. Improper installation could result in the gate becoming unstable or
dislodged from the doorway. Always make sure the extension is securely attached
to the gate before using. The safety of your child is your responsibility. Please keep
these instructions for your reference.
IMPORTANT
• The four mounting brackets must be used in securing the gate to the wall.
These brackets prevent the gate from dislodging from its opening and
becoming unstable.
• If hardware mounting to a surface other than drywall or wood, please
consult with a professional about installation.
• The maximum width of this gate is 192 inches.

English4
WARNING
• To prevent serious injury or death, securely install gate
or enclosure and use according to manufacturer's
instructions.
• Children have died or been seriously injured when gates
are not securely installed. ALWAYS install and use as
directed using all required parts.
• STOP using when a child can climb over or dislodge
the gate.
• Use only with the locking mechanism securely engaged.
• To prevent falls, NEVER use at top of stairs.
• NEVER use to keep child away from pool.
• Intended for use with children from 6 months
through 24 months.
• Always ensure the gate is resting against the floor before
beginning installation.
• This product will not necessarily prevent all accidents.
Never leave child unattended.
• Check the gate regularly to see if all the hardware and
mountings are tightened.
• Do not use if any component is missing or damaged.
• Adult assembly required.

A
C
B
English 5
PLEASE CHECKTO MAKE SUREYOU HAVE THE FOLLOWING PARTS:
A Play Yard Gate Frame (8 Panels)
B Plastic Mounting Brackets (4 – Attached to Gate Frame)
C 1" Wall Mounting Screws (8) (requires a Phillips/cross-head screwdriver)
Before Assembly

English6
STEP 1
Unfold the gate frame by turning the locking knobs counter clockwise at
each pivoting joint. Loosen the knobs enough to allow the gate to swing
open freely without fully removing the knobs.
Option A: Installing Your Gate Between Two Walls
LOCKING KNOB
STEP 2
Use a Phillips/crosshead screwdriver to fix the wall mounting bracket to
the wall. Repeat for all four brackets.

English 7
STEP 3
Arrange the panels to your desired configuration, then tighten all of the
locking knobs.
NOTE: This gate is designed to fit openings 50.5 inches (128.27cm) to 192 inches
(487.68).
50-1/ 2" M inim um Wid th

English8
STEP 1
Unfold the gate frame by turning the locking knobs counter clockwise at
each pivoting joint. Loosen the knobs enough to allow the gate to swing
open freely without fully removing the knobs.
METAL PIVOT BAR (2)
LOCKING KNOB (2)
TOOTHED DISK (2)
WALL MOUNT BOTTOM
CAP – MALE (1)
WALL MOUNT BRACKET (2)
WALL MOUNT
TOOTHED DISK (1)
WALL MOUNT BOTTOM
CAP – FEMALE (1)
Option B: Installing Your Gate as a Freestanding Enclosure
STEP 2
Release the vertical metal pivot bars at each end of the play yard by
removing the following parts from the assembly:

English 9
STEP 3
Position the play yard into your desired configuration (e.g. octagon, square),
then join the free ends of the play yard together at the plastic joints.
STEP 4
Insert one of the previously removed metal pivot bars through the opening
created by joining the upper plastic joints. Guide the metal pivot bar
downward into the circular housing on the lower plastic joint.

English10
STEP 5
Reassemble the upper locking joint by adding one of the previously removed
toothed disks and locking knobs.
STEP 6
Tighten each of the locking
knobs by turning them
clockwise, fixing the play yard
into the configuration you have
chosen. To position the play
yard into a new configuration
or shape, simply loosen each
of the locking knobs, adjust
and retighten.
NOTE: When adding or removing additional panel units to the
configuration, panels must be added or subtracted in sets of two for the
freestanding enclosure to function properly.

English 11
STEP 1
Pull both sides of the slide lock sideways away from the metal lift latch while
simultaneously pivoting the metal lift latch upward from the gate’s door frame.
STEP 2
To relock the gate, close the door completely and drop the metal lift latch back
into place. The slide lock will return to it’s locked position on its own.
Operating the Door Latch
SLIDE LOCKMETAL LIFT LATCH

English12
TO FOLDYOUR PLAY GATE
STEP 1: Loosen all of the locking knobs so the play yard can move freely
and becomes flexible at the joints.
STEP 2: Remove one of the locking knobs from the play yard and remove one
vertical tube.
STEP 3: You will now be able to pull the two plastic joints and the top and bottom
of the play yard apart.
STEP 4: Fold and put away.
CARE AND MAINTENANCE
Periodically check the gate for signs of damage, wear, or missing components.
Do not use if any part is missing, worn or damaged. Check the gate regularly to
ensure all the hardware and mountings are tightened. Do not use abrasive
cleaners or bleach. Clean by sponging with warm water and a mild detergent.
90 DAYS LIMITED WARRANTY
If, during the first 90 days after consumer purchase of the item, under reasonable
and non-commercial use and conditions of maintenance, it fails while owned by
the original purchaser because of the quality of materials or workmanship of finish
and assembly, Regalo International, LLC, will replace or repair it at Regalo’s option.
PROOF OF PURCHASE REQUIRED.

English 13
Replacement Parts
A Door Frame Toothed Hinge
White = #13009
Black = #11009
B Top Hinge
White = #13011
Black = #11011
C Locking Knob
White = #13005
Black = #11005
D Toothed Hinge
White = #13012
Black = #11012
E Wall Mount Bracket
White = #13007
Black = #11007
F Wall Mount Bottom
Cap – Male
White = #13010
Black = #11010
G Bottom Hinge – Female
White = #13006
Black = # 11006
H Door Frame Bottom Hinge
White = #13004
Black = #11004
IBottom Hinge – Male
White = #13002
Black = #11002
JWall Mount Bottom
Cap – Female
White = #13014
Black = #11014
K 1" Wall Mount Screws
#10001
L 27" Metal Pivot Bar
White = #13008
Black = #11008
M Wall Mount Toothed Disk
White = #13013
Black = #11013
N Toothed Disk
White = #13003
Black = #11003
A B C
J
K
L
D
E
F
N
M
G
HI

French14
www.regalo-baby.com
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100 / Burnsville, MN 55306, É.-U.
866.272.5274 (aux États-Unis seulement) ou 952.435.1080
Fabriqué en Chine
Barrière de sécurité
pour parc de jeu 4 en 1
GUIDE D'UTILISATION MODÈLE: 1350, 1350DS, 1350B
• LIRE TOUTES LES INSTRUCTIONS AVANT D’ASSEMBLER ET
D’UTILISER LA BARRIÈRE.
• CONSERVER CES INSTRUCTIONS POUR UNE UTILISATION
ULTÉRIEURE.

French 15
Avant d'utiliser le produit
Lire et suivre attentivement les instructions pour assurer une installation conforme
de la barrière et des rallonges. Une mauvaise installation risque d'aboutir à une
barrière branlante, ou qui se détache de l'ouverture. Avant utilisation, toujours
s'assurer que la rallonge est fixée solidement à la barrière. Vous êtes responsable
de la sécurité de votre enfant. Conserver ces instructions pour consultation.
IMPORTANT
• Les quatre supports de montage doivent être utilisés pour fixer la barrière
au mur. Ces supports empêchent la barrière de sortir de son ouverture et de
devenir instable.
• Si la surface de fixation n'est pas une cloison sèche ou du bois, consulter un
spécialiste au sujet de l'installation.
• La largeur de cette barrière ne peut excéder 487.68cm (192 po).

French16
MISE EN GARDE
• Pour prévenir des blessures graves voire mortelles,
assembler solidement la barrière ou le parc; leur utilisation
doit être conforme aux directives du fabricant.
• Des enfants sont morts ou ont subi de graves blessures
en raison de barrières et de parcs mal fixés. TOUJOURS
installer et utiliser les barrières et les parcs conformément
aux directives en utilisant toutes les pièces nécessaires.
• CESSER l'utilisation si un enfant est capable de grimper
par-dessus la barrière ou le parc ou de les déloger.
• Installer de façon que le mécanisme de verrouillage se
trouve du côté opposé à l'enfant.
• Pour éviter les chutes, ne jamais utiliser la barrière en haut
des escaliers.
• NE JAMAIS utiliser pour tenir les enfants à l'écart d'une
piscine.
• Destiné aux enfants de 6 à 24 mois.
• Toujours s'assurer que la barrière repose sur le sol avant
de commencer l'installation.
• Cet article ne prévient pas nécessairement tous les
accidents. Ne jamais laisser l'enfant sans surveillance.
• Vérifier régulièrement le serrage des pièces de montage
et de fixation.
• Ne pas utiliser s'il manque des pièces ou elles sont
endommagées.
• Assemblage adulte requis.

A
C
B
French 17
VEUILLEZ VÉRIFIER QUE VOUS DISPOSEZ DES ARTICLES SUIVANTS:
A Cadre de la barrière pour parc de jeu (8 panneaux)
B Supports de montage en plastique (4 – attachés au cadre de la barrière)
C Vis de montage mural de 2,5 cm (1po) (8) (tournevis cruciforme/Phillips)
Avant l'assemblage

French18
ÉTAPE 1
Dépliez le cadre de la barrière en desserrant les boutons de blocage de
chaque articulation dans le sens contraire aux aiguilles d'une montre.
Desserrez suffisamment les boutons, mais sans les enlever, pour permettre
à la barrière de s'ouvrir librement.
Option A: Installation de la barrière entre deux murs
BOUTON DE BLOCAGE
ÉTAPE2
Utilisez un tournevis cruciforme/Phillips pour fixer le support de montage
mural au mur. Répétez pour les quatre supports.

French 19
ÉTAPE3
Disposez les panneaux selon la configuration désirée, puis serrez tous les
boutons de blocage.
REMARQUE : Cette barrière est conçue pour s'adapter à des ouvertures
comprises entre 128.27cm et 487.68cm (50.5 po et 192 po).
50-1/ 2" M inim um Wid th
128 cm (50,5 po)

French20
ÉTAPE 1
Dépliez le cadre de la barrière en desserrant les boutons de blocage de
chaque articulation dans le sens contraire aux aiguilles d'une montre.
Desserrez suffisamment les boutons, mais sans les enlever, pour permettre
à la barrière de s'ouvrir librement.
BARRE MÉTALLIQUE À PIVOT (2)
BOUTON DE BLOCAGE (2)
DISQUE DENTÉ (2)
CAPUCHON INFÉRIEUR POUR
MONTAGE MURAL – MÂLE (1)
SUPPORT POUR
MONTAGE MURAL (2)
DISQUE DENTÉ POUR
MONTAGE MURAL (1)
CAPUCHON INFÉRIEUR
POUR MONTAGE
MURAL – FEMELLE (1)
Option B: Installation de votre barrière comme
structure autoportante
ÉTAPE2
Libérez les barres métalliques à pivot à chaque extrémité du parc de jeu
en retirant les pièces suivantes de l'assemblage: