Regalo 1348DS User manual

www.regalo-baby.com
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100 / Burnsville, MN 55306, USA
866.272.5274 (U.S. only) or 952.435.1080
Made in China
Double Door Super Wide
Safety Gate
OWNER’S MANUAL MODEL: 1348, 1348DS
• READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE.
• KEEP INSTRUCTIONS FOR FUTURE USE.

English 3
Before Using Product
Read and follow all instructions carefully to ensure that your gate and extensions are
properly installed. Improper installation could result in the gate becoming unstable or
dislodged from the doorway. Always make sure the extension is securely attached
to the gate before using. The safety of your child is your responsibility. Please keep
these instructions for your reference.
IMPORTANT
• The four mounting brackets must be used in securing the gate to the wall.
These brackets prevent the gate from dislodging from its opening and
becoming unstable.
• If hardware mounting to a surface other than drywall or wood,
please consult with a professional about installation.
• The maximum width of this gate is 192 inches.

English4
WARNING
• To prevent serious injury or death, securely
install gate or enclosure and use according to
manufacturer’s instructions.
• Children have died or been seriously injured
when gates are not securely installed. ALWAYS
install and use gate as directed using all required
parts.
• STOP using when a child can climb over or
dislodge the gate.
• Use only with the locking/latching mechanism
securely engaged.
• To prevent falls, NEVER use at top of stairs.
• NEVER use to keep child away from pool.
• Intended for use with children between 6 and 24
months.
• Always ensure the gate is resting against the floor
before beginning installation.
• This product will not necessarily prevent all
accidents. NEVER leave child unattended.
• Check the gate regularly to see if all the hardware
and mountings are tightened.
• Do not use if any components are missing or
damaged.
• Adult assembly required.

English 5
D E
A B C
G HF
Before Assembly
Primary Door Panel (1)
Secondary Door Panel (1)
Gate Frame (6 Panels)
Plastic Mounting Brackets (4 – Attached to Gate Frame)
U-frame Support (1)
1" Wall Mounting Screws (8) (requires a Phillips/cross-head screwdriver)
Frame Assembly Screws (4)
Hex Key
PLEASE CHECK TO MAKE SURE YOU HAVE THE FOLLOWING PARTS:
A
B
C
D
E
F
G
H

English6
STEP 1
Connect the double doors by pushing the door frames together until the bases
meet.
STEP 2
Place the U-frame support on top of the connected door base an align screw
holes.
STEP 3
Use the hex key to fix the U-frame support to the door frame bases using
the frame assembly screws.
Assembling Your Gate

English 7
LOCKING KNOB
STEP 1
Option A: Installing Your Gate Between Two Walls
Unfold the gate frame by turning the locking knobs counter clockwise at each
pivoting joint. Loosen the knobs enough to allow the gate to swing open freely
without fully removing the knobs.
STEP 2
STEP 3
Use a Phillips/cross-head screwdriver to fix the wall mounting bracket to
the wall. Repeat for all four brackets.
Arrange the gate panels to your desired configuration to fit your opening
properly.

English8English8
NOTE:
to maximum width openings 192 inches wide.
52.5 INCHE S
Tighten all the locking knobs to secure your gate in place.
STEP 4

English 9
Option B: Converting Your Gate to a Play Yard
STEP 1
Unfold the gate frame by turning the locking knobs counter clockwise at
each pivoting joint. Loosen the knobs enough to allow the gate to swing
open freely without fully removing the knobs.
STEP 2
METAL PIVOT BAR (2)
WALL MOUNT
TOOTHED DISK (1)
LOCKING KNOB (2)
TOOTHED DISK (2)
WALL MOUNT BOTTOM
CAP - MALE (1)
WALL MOUNT BRACKET (2) WALL MOUNT BOTTOM
CAP - FEMALE (1)
Release the vertical metal pivot bars at each end of the play yard by
removing the following parts from the assembly:

English10
STEP 3
Position the play yard into your desired configuration (e.g. square), then join
the free ends of the play yard together at the plastic joints.
STEP 4
Insert one of the previously removed metal pivot bars through the opening
created by joining the upper plastic joints. Guide the metal pivot bar
downward into the circular housing on the lower plastic joint.

English 11
STEP 5
Reassemble the upper locking joint by adding one of the previously removed
toothed disks and locking knobs.
STEP 6
Tighten each of the locking
knobs by turning them
clockwise, fixing the play yard
into the configuration you have
chosen. To position the play
yard into a new configuration
or shape, simply loosen each
of the locking knobs, adjust
and re-tighten.

English12
Operating the Single Door
METAL LIFT LATCH SLIDE LOCK
Simultaneously slide the lock and lift up the metal lift latch to unlock the door.
The primary door will swing open in one direction only.
STEP 1
STEP 2
To lock the gate, close the door completely and push the metal lift latch back
into place.

English 13
Operating the Double Doors
STEP 1
LOCKING HINGE ROTATING LOCKING HINGE
After you have opened the primary door, rotate the locking hinge on the
secondary door. Lift the door up and swing open. The secondary door will open
in either direction.
SECURED
LOCKING HINGE
STEP 2
To close the secondary door, lift up on the door and place onto door frame
base. Rotate the locking hinge to secure in place.
NOTE: Secondary door will only function when the primary door is open.

English14
TO FOLD YOUR GATE
STEP 1: Loosen all the locking knobs so the gate can move freely and become
flexible at all the joints.
STEP 2: Remove one of the locking knobs from the gate and remove one metal
pivot bar.
STEP 3: You will now be able to pull the two plastic joints at the top and bottom
of the gate apart.
STEP 4: Fold and put away.
CARE AND MAINTENANCE
Periodically check the gate for signs of damage, wear, or missing components.
Do not use if any part is missing, worn or damaged. Check the gate regularly to
ensure all the hardware and mountings are tightened. Do not use abrasive
cleaners or bleach. Clean by sponging with warm water and a mild detergent.
90 DAYS LIMITED WARRANTY
If, during the first 90 days after consumer purchase of the item, under reasonable
and non-commercial use and conditions of maintenance, it fails while owned by
the original purchaser because of the quality of materials or workmanship of finish
and assembly, Regalo International, LLC, will replace or repair it at Regalo’s option.
PROOF OF PURCHASE REQUIRED.

English 15
Replacement Parts
F
K
O
D C B A
N
M
L
J
HIG
E
A
White = #13009
B
White = #13011
C
White = #13005
D
White = #13012
E
White = #13007
F
White = #13010
G
White = #13006
H
White = #13141
Door Frame Toothed Hinge
Top Hinge
Locking Knob
Toothed Hinge
Wall Mount Bracket
Wall Mount Bottom
Cap - Male
Bottom Hinge - Female
Door Frame Bottom Hinge
I
White = #13002
J
White = #13014
K
#10001
L
White = #13008
M
White = #13013
N
White = #13003
O
#10050
Bottom Hinge - Male
Wall Mount Bottom
Cap - Female
1” Wall Mount Screws
27”Metal Pivot Bar
Wall Mount Toothed Disk
Toothed Disk
Frame Assembly Screw

www.regalo-baby.com
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100
Burnsville, MN 55306, USA
866.272.5274 (U.S. only) or 952.435.1080
20180430ET