Regency City Series San Francisco Bay 40 User manual

Regency City Series San Francisco Bay 40
CB40E-NG11 / CB40E-LP11
FRAMING
DIMENSIONS
SPECIFICATIONS
HEAT RELEASE REQUIREMENTS
QR LINK FOR
PDF DIGITAL COPY
OF SPECIFICATIONS:
MUST READ BEFORE
FRAMING
IMPORTANT INFORMATION

City Series CB40E-11
Gas Line Entry
throughout this manual. The inches are rounded to the

City Series CB40E-11
Ventilation Openings
Release warmth into the room discreetly
Front Exit
The ventilation opening may be placed in front ensuring it meets the 120
to =100%.
Top Exit
The ventilation opening may be short of the ceiling as shown below.
enclosure to the ceiling and must be in open in front and both sides to
Ventilation Opening Locations
The following are examples of how the ventilation openings may be placed
ventilation opening. The ventilation opening(s) must be a minimum 120
The ventilation opening may be fully open at the top of the enclosure.
This type of ventilation opening would be used when the top of the
enclosure is not visible from above and where the ceiling within the
other preventative measures should be put into place.
The ventilation opening may be placed on top ensuring it meets the 120
when the top of the enclosure is visible from above and where the ceil-
ing within the room is higher than normal.

City Series CB40E-11
Chase Enclosure
Top of chase enclosure
Top of chase
Top of chase enclosure
top of the chase enclosure for all installations.
2
examples shown in this manual.
Internal chase:
enclosure causing the enclosure to overheat. It is vital that all the hot air from within the enclosure exits through the ventilation openings only.

City Series CB40E-11
Levelling bolts
There are four levelling bolts - two on each side
These can be adjusted using the open end wrench
Locating Your Gas Fireplace
ensure that the clearances are met.
application. The appliance must be installed on
a metal or wood panel extending the full width
and depth of the appliance.
Diagram 1
CB40E
a remote control.
for details.
-
tion on paper using exact measurements for
installing this appliance. Have an authorized
before installation.
Note:
Locations" section.
WARNING!
screw. Bend into the correct shape (see above).
the unit and attach the other end with one screw.
The front access panel may be removed for ease
ensure that the access panel is reinstalled prior to
See locations in diagrams to the right.
Nailing strips are shipped with the appliance and will
need to be attached. Note that the nailing strips are
1. Secure nailing strip to appliance with 2 screws
per side.
2. Secure nailing strips to framing using wood or
metal screws.

City Series CB40E-11
NOT be
recessed into combustible construction.
WARNING
instructions.
Clearances
**
B: Sidewall (on one side)
**
Side wall to side wall (min.)
G: To Enclosure Ceiling (min/max) From top of enclosure
* Top/front or side of enclosure
To Top of Ceiling
L: Chase Enclosure (min.)
Perpendicular from chase grill
Hearth
See mantel clearances chart in this manual
Horizontal - Top
Horizontal - Side
Horizontal - Bottom
Passing through wall/
floor/ceiling - when
The HeatWave
-
HeatWave
manual for details.
M

City Series CB40E-11
Note: The ventilation opening
Clearances
Floor to ceiling with top opening Low framing with vents in front/2 sides or top
Full framing with low vents in front or 2 sides Full framing with vents in front or 2 sides

City Series CB40E-11

City Series CB40E-11

City Series CB40E-11

City Series CB40E-11
DIMENSIONS
B
C -
sure.
on the wall.

City Series CB40E-11
Secure with screws through louvers to the sides.
may not be
but the drawing dipicts the process.
DIMENSIONS
-
sure.
B
C
on the wall.
Repeat steps to install the second grill to the other side of the chase.

City Series CB40E-11
Mantel Clearances
Combustible mantel clearances from top of front facing
are shown in the diagram on the right.
Mantel Leg Clearances
Combustible mantel leg clearances as per diagram:

City Series CB40E-11
NOTE:
for the product to facilitate ease of installation. See instructions in this manual for details.
Description
Framing Height
B
*C
G
Note:
Note:
Note:
Note: This appliance must be in-
stalled on a solid surface such as a
width and depth of the appliance.
*
header on edge
-
studs in front and both
sides. Studs behind can be

City Series CB40E-11
Part A Install
Screw Locations

City Series CB40E-11
Part J install to Part B1 + B2
Part J screw locations
Secure Framing to Wall Studs with wood screws
Install Pre Assembled Sidewall
Install Pre Assembled Sidewall (opposite)
Part B1 to A - screws go in from front

City Series CB40E-11
Telescope LEFT + RIGHT sidewalls to desired height
Set predetermined height when using wood panel kit
Attach Part O (x2) and Q (x2) to Part B2
Attach Part O (x2) to Part B3
Part B3
Part B3
Part Q
Part O Part O
LEFT RIGHT
Attach Part S and Part H to Front of LEFT + RIGHT sides

City Series CB40E-11
Attach Part I (x2) to Part S & H
Attach Part M (x2) to Part L
Part I screw holes located on the side
Attach Part L (x2) to LEFT and RIGHT sides
Part L
Part M
Part H
Part Q
Part S
Part I
Screw holes in Part I
located on the side
Part M

City Series CB40E-11
Swing Parts O out and attach
Attach Part P (Left) to the LEFT SIDE + H1
Attach Part P (Right) to the RIGHT SIDE + H1

City Series CB40E-11
Front view Part ID - extended shown
Back view Part ID - extended shown