Regency Greenfire GF1500L NG-2 User manual

 GreenreGF1500L-2 |1
Greenre®GF1500L-2 Gas Fireplace
MODEL GF1500L NG-2 GF1500L LP-2 GF1500L ULPG-2
Fuel Type Natural Gas Propane ULPG
Gas Consumption 50MJ/h 49MJ/h 44MJ/h
Manifold
Pressure 0.87kPa 2.49kPa 2.49kPa
Injector Size 1x#29
3.40mm
1x#47
1.99mm
1x#49
1.85mm
1151mm
344mm
1263mm
633mm
249mm
117mm
37mm
159mm
459mm
13mm
737mm
824mm
945mm
560mm
523mm

2| GreenreGF1500L-2
CLEARANCES
Caution Requirements
Thetop,backandsidesofthereplacearedenedby
standos.ThemetalendsofthestandomayNOTbe
recessedintocombustibleconstruction.
WARNING
Fire hazard is an extreme risk
if these clearances (air space) to combustible materials are
not adhered to. It is of greatest importance that this replace
and ue system be installed only in accordance with these
instructions.
The clearances listed below are minimum distances unless otherwise stated:
A major cause of chimney related res is failure to maintain required clearances (air space) to combustible materials. It is of the greatest
importance that this replace and ue system be installed only in accordance with these instructions.
Clearance: Dimension Measured From:
A: Mantel Height (min.) 254mm TopofFireplaceOpening/HotAirOutlet
B: Sidewall (on one side) 152mm SideofFireplaceOpening/HotAirOutlet
C: Ceiling
(room and/or alcove)
1162mm TopofFireplaceOpening/HotAirOutlet
D: Mantel Depth (max.) 305mm 730mmAboveFireplaceOpening/Hot
AirOutlet
E: Alcove Width 1524mm SidewalltoSidewall(Minimum)
F: Alcove Depth 914mm FronttoBackWall(Maximum)
G: From Floor 617mm TopofFireplaceOpening/HotAirOutlet
Note: 0 Nohearthrequired
Installed close
to ceiling.
Flue Clearances to Combustibles
Horizontal-Top 76mm
Horizontal-Side 51mm
Horizontal-Bottom 51mm
Vertical 51mm
Alcove
E
F
F
E
D
A
B
Installed Close
to Floor
G
IMPORTANT: If installing a television above
this appliance, the television must be either
fully recessed into the wall above the
replace and or have a mantle below the
television. If the television is left unprotected,
the extreme heat being emitted from this
appliance will result in damage to the
television. See clearance requirements for
both mantle (page 9) and or enclosing the
top of the appliance (page 11 (D) dimension).
GF1500L-2 Gas Fireplace

 GreenreGF1500L-2 |3
FRAMING DIMENSIONS
Framing
Dimensions Description GF1500
A FramingHeight 945mmcombustiblenish
A¹FramingHeight-SteelStud 846mmnoncombustiblesteelstud
B FramingWidth 1394mm
CFramingDepth 568mm
D MinimumHeighttoCombustibles 1225mm
ECornerWallDepth 1460mm
F CornerFacingWallWidth 2065mm
GVentCenterlineHeight 1016mm
H* Non-combustiblefacingheight *seenon-combustiblefacingheightinthismanual
IGasConnectionOpeningHeight 38mm
J GasConnectionHeight 67mm
KGasConnectionInset 44mm
L GasConnectionOpeningWidth 89mm
NOTE:Aminimumthicknessof12mmnon-combustiblefacingboardcompliantwithAS1530-1andAS1530-3isrequired
whenusingthenoncombustibleushnishingoption.Aminimumthicknessof10mm-19mmcombustiblefacingboardis
requiredwhenchoosingthecombustibleushnishingoption.
Note:mustmaintain13mmairgapallaroundtheperimeteroftheappliancewhenchoosingthisoption.
D
G
H
Non-Combustible
Facing
Header
F
E
I
J
K
L
Flex or Rigid Pipe
Drywall or
other facing
C
C
A
B
C
Timber
Studs
Finished Floor
A
B
C
Timber
Studs
Finished Floor
Non-combustible Flush Finishing Framing
A
1
Steel Stud
on edge
NOTE: Do not place timber
studsbelowthetimberfram-
ing studs already in place.
Additional steel studs must
be added as shown when
choosingthenoncombustible
ushnishingoption.
Note:Steelstudmustbeinstalledafter
unithasbeenpositionedinplaceand
priortoinstallationofnon-combustible
nishing
Note: Ifraisingtheunit,thenthe
minimumframingheightmeasure-
ment(A)mustbeadheredto.
For example: Unit raised 300mm
thenA+300mm=1240mm.
CombustibleushnishingFraming
IMPORTANT NOTE:
This unit can be nished
with combustible facing
material of thickness range
10-19mm OR non-combus-
tible facing material of a
minimum thickness 12mm.
GF1500L-2 Gas Fireplace

4| GreenreGF1500L-2
GF1500L-2 Gas Fireplace
Combustible Requirements
FRAMING & FINISHING (COMBUSTIBLE)
Note:
Dependingonthematerialusedfornishing,thenailingstripsmust
besetaccordinglysothatthenishedmaterialisalwaysbeush
withtheedgeoftheange.
If nishing with material with a combined thickness greater
than 19mm, non-combustible material must be used.
Note:
*Finishing Trim or one of the fascias must be used with
combustible nishing.
10mm to 19mm combustible nishing can be used if the 13mm
airgaparoundthefrontfacingoftheunitismaintained.Finishing
materialcannotbethickerthan19mmandmustbeushwiththe
frontedgeoftheange.
Note:
• The siding nailing strips are factory set at 10mm. The top
nailingstripisxedduringtransittotherearoftheappliance.
• Donotplaceanyreinforcementinfrontofheaderandbehind
nishingmaterial.
• Thenailingstripmustbeused.Itisxedduringtransittothe
rearoftheunit.
NOTE:
Theappliancemustbeinstalledonaat,
solid,continuoussurfaceForexamplea
wood,metalorconcreteoor.Inaraised
(onthe wall) application the appliance
must be installed on a metal or wood
panelextendingthefullwidthanddepth
oftheappliance.
NOTE:
Donotremovethestandoswhichare
locatedaroundtheperimeterothisunit
Theseareinplaceandactasaguidefor
thecombustiblematerialtobeplaced.
148mm
482 mm
1288 mm
630 mm
Finished
Material
10mm-19mmthick-
nessusingcombusti-
blenishing
Note:mustmaintain
13mmairgapall
around
(seediagramsbelow
andonnextpage)
1stslot
Unit
13mm
gap
NOTE: Maintain a 13mm gap
all round.
A minimum of 10mm to
maximum 19mm material
thickness is required.

 GreenreGF1500L-2 |5
GF1500L-2 Gas Fireplace
CLEARANCES FOR COMBUSTIBLE FINISHING WITH MANTEL
Due to the extreme heat this replace emits, the mantel clearances are critical.
Combustiblenishingandmantelclearancesareshowninthediagram
ontheright.FinishingTrimmustbeusedwithcombustiblenishing.
Note: Maximum combustible nishing material thickness is
19mm measured from the front of the replace opening.
If total nishing material is greater than 19mm, non-
combustible must be used.
Note:Ensurethepaintthatisusedonthemantelandthe
facingis"highquality"orthepaintmaydiscolour.
Note:Combustiblemantelstartsat796mm(618mm+178mm)
fromunitbase.
COMBUSTIBLE MANTEL LEG CLEARANCES
Mantelleg&combustiblenishingclearancesasperdiagram:
Combustible Material
(152mm)
(305mm)
(0)
(630 mm)
To unit base
(322 mm)
Top of
Fireplace
Opening
(576 mm)
(305mm)
(470 mm)
(241mm)
Combustible Stud
(On Edge)
Nailing Flange
Combustible facing
(min. 10mm- max. 19mm)
(297 mm)
(200mm)
(100mm)
(372 mm)
Allowable mantel
leg projection
181mm
254mm
330mm
38mm
MANTEL LEG
102mm
178mm
Allowable mantel
leg projection
181mm
254mm
330mm
38mm
MANTEL LEG
102mm
178mm
Allowable mantel
leg projection
181mm
254mm
330mm
38mm
MANTEL LEG
102mm
178mm
13mm Gap 13mm Gap
Combustible Combustible
Important:

6| GreenreGF1500L-2
CLEARANCES FOR NON-COMBUSTIBLE FLUSH FINISHING WITH MANTEL
Due to the extreme heat this replace emits, the
mantel clearances are critical.
Combustiblemantelclearancesfromtopoffrontfacingare
showninthediagramontheright.
Note:Foraushednishusingnon-combustiblenishing,
seven13mm stand-otabs aroundthereplace opening
mustbebrokeno.Thetopnailingangecannotbeused
andanon-combustiblesteelstudmustbeinstalledtosupport
thenon-combustiblefacing.
Note: Ensure the paint that is used on the
mantel and the facing is "high quality"
or the paint may discolour.
Note:Combustiblemantelstartsat796mm(605mm
+191mm)fromunitbase.
NON COMBUSTIBLE MANTEL LEG CLEARANCES
Mantelleg&Non-combustiblenishingclearancesasperdiagram:(FlushedFinish)
Allowablemantel
leg projection
181mm
254mm
330mm
38mm
MANTELLEG
102mm
178mm
Allowablemantel
leg projection
181mm
254mm
330mm
38mm
MANTELLEG
102mm
178mm
Allowablemantel
leg projection
181mm
254mm
330mm
38mm
MANTELLEG
102mm
178mm
83mm
Non-combustible
83mm
Non-combustible
Combustible Material
(152 mm)
(305mm)
(0 mm)
To Uni
t
Base
(617 mm)
(335 mm)
Top of
Fireplace
Opening
(589mm)
(305 mm)
(457 mm)
(254mm)
Non-Combustible facing (min.12 mm)
Non-Combustible steel stud
846 mm to underside
of steel stud
(100mm)
(310 mm)
(200mm)
(385 mm)
GF1500L-2 Gas Fireplace

 GreenreGF1500L-2 |7
GF1500L-2 Gas Fireplace
NON COMBUSTIBLE REQUIREMENTS
FLUSHED FINISHING & FRAMING WITH NON-COMBUSTIBLE MATERIAL
Note: Forush nishing,thetop nailing stripmustbe removedand a
non-combustiblesteelstudsupportadded.
Thesevenreplaceopeningstandoswhicharelocatedonthisunitcan
beremovedwhennoncombustiblematerialisinstalledushwiththeunit.
(seeP.13).
Non-combustiblenishingmaterialonthetopandsidesmustalsobeused.
NOTE:
Theappliancemustbeinstalledon
aat,solid,continuoussurfaceFor
exampleawood,metalorconcrete
oor. In a raised (on the wall)
applicationtheappliancemustbe
installedonametalorwoodpanel
extendingthefullwidthanddepth
oftheappliance.
871 mm
605 mm
1432 mm
Non-combustible
Combustible
Combustible
Steel Stud
on edge
Timber Stud
Timber Stud
159 mm 446 mm
Non-Combustible
Material
Combustible
Material
Finished
Material
*diagramsshownbelow
arewithtopnailingstrip
removed.
12mm
25mm
38mm
Unit
Unit
Unit MINIMUM THICKNESS OF THE FINISH MATERIAL: 12MM
A minimum thickness of 12mm
non-combustible facing is required.

8| GreenreGF1500L-2
OPTIONAL FRAMING KIT
920-194 01/28/20
OPTIONAL FRAMING KIT
1. Construct the timber framing, ensure inside dimensions are 1095 mm H
x 1394 mm W as shown below.
NN
NN
2. Bend both side nailing strips from the side of the appliance until
positioned as shown below. Determine the overall combined thickness
of the non-combustible board + finished material being used. The
nailing strips can be adjusted up to 38mm. Remove top nailing strip and
recycle.
3. Adjust the nailing strips by loosening 2 screws on each nailing strip -
adjust and retighten screws.
NOTE: depending on the finishing material used.
4. Attach both vertical studs (607-065) to the vertical timber studs and
secure using 6 screws, as shown.
NOTE: Ensure the flat side of the steel stud is facing the timber framing.
(607-065)
Flat side out
5. Secure horizontal steel header stud (606-067) with 2 screws per side as
per diagram.
6. Slide the unit into position. Hook up gas, flueing, electrical and
conversion kit (if purchased) prior to installing the remaining steel studs.
7. Secure the upper horizontal steel stud (606-067) as shown with 2
screws per side.
8. Secure the top large horizontal stud (607-027) with 2 screws per side
as shown. Bring finishing material to the edge of the top framing lip on
large stud (607-027).
9. Install the large lower stud (607-066) with 2 screws on each side.
Header stud
(606-067)
606-067
607-065
607-027
607-066
607-065
Nailing Strips
Remove Top
Nailing Strip
Large stud
(607-027)
Large stud
(607-066)
Horizontal stud
(606-067)
tooltip
Framing Lip
Finishing with
non combustible
material
Use Top Holes
Finishing with
combustible material
Use lower holes
1
GF1500L-1
GF1500L-2 Gas Fireplace

 GreenreGF1500L-2 |9
GF1500L-2 Gas Fireplace
FRAMING & FINISHING (CLEAN FINISH INSTALLATIONS ONLY)
Note: When constructing the framed opening, please ensure there is access to install the gas lines when the unit is
installed.
2. Forexteriorwalls,insulatetheenclosuretothesamedegreeastherestofthehouse,applyvapourbarrieranddrywall,asperlocalinstallation
codes.(Do not insulate the replace itself and/or the ueing. Clearances must be maintained as per this manual.)
WARNING: Failure to insulate and add vapor barriers to the inside of the exterior wall will result in operational and performance
problems including, but not limited to: excessive condensation on glass doors, poor ame package, carbon, blue ames etc. These
are not product related issues.
3. Theunitdoesnothavetobecompletelyenclosedinachase.Youmustmaintainclearancesfromtheuetocombustiblematerials:See"Clearances"
section.Combustiblematerialscanbelaidagainstthesideandbackstandosandtheappliancebase.
4. Non-combustiblematerial(ie.tile,slate,etc)maybebroughtuptoandoverlaptheunit(topandbottom)ensuringthatthemaximumthickness
doesnotgobeyondthe38mmasshowninthediagrambelow.Thefaceplatewillnotbeabletobemountedifnishedmaterialisbeyond38mm.
1. Frameintheenclosurefortheunitwithframingmaterial.
IMPORTANT: The framed opening must be of non-combustible material.
Ensure  front of facing material is
ushwiththeedgeoftheangeon
thereplace.

10 | GreenreGF1500L-2
FLUEING INTRODUCTION
TheGF1500Lusesthe"balancedue"technologyCo-Axialsystem.Theinnerlinerventsproductsofcombustiontotheoutsidewhiletheouterliner
drawsoutsidecombustionairintothecombustionchambertherebyeliminatingtheneedtouseheatedroomairforcombustionandlosingwarmroom
airupthechimney.
Note: These ue pipes must not be connected to any other appliance.
Thegasapplianceanduesystemmustbeventeddirectlytotheoutsideofthebuilding,andneverbeattachedtoachimneyservingaseparatesolidfuel
orgasburningappliance.Eachdirectventgasappliancemustuseit'sownseparateuesystem.Commonuesystemsareprohibited.
FLUEING ARRANGEMENT FOR HORIZONTAL TERMINATIONS
Thediagramshowsallallowablecombinationsofverticalrunswithhorizontalterminations,usingone90o(two45o elbowsequalone90oelbow).
Note: Must use optional rigid pipe adapter (Part# 770-994) when using Simpson Dura Vent Only.
• Maintain clearances to combustibles as listed in "Clearances" section
• Horizontal ue must be supported every 0.9m
• A ue guard should be used whenever the termination is lower than the specied minimum or as per local codes.
• Flex system can only be used up to 3m - otherwise rigid system must be used.
FLUE RESTRICTOR SETTING:
Flue restrictor factory set at Set 0.
Refertothe"FlueRestrictorPosition"sectionfordetailsonhowtochangetheuerestrictorfromthefactorysettingofSet0toSet1ifrequired.
1061 mm
Minimum
Height
Requirement
2
3
3
Restrictor Set #0
Full Open
Restrictor Set #1
44 mm-Open
6.0
6.5
Meters
4.0 4.2
Restrictor Set #2
41 mm-open
GF1500L-2 Gas Fireplace