Regency Gem54 Quick start guide
WARNING:
If the information in these instructions are not followed
exactly, a re or explosion may result causing property
damage, personal injury or loss of life.
FOR YOUR SAFETY
Do not store or use gasoline or other ammable vapors and
liquids in the vicinity of this or any other appliance.
Installation and service must be performed by a qualied
installer, service agency or the gas supplier.
FOR YOUR SAFETY
What to do if you smell gas:
Do not try to light any appliance
Do not touch any electrical switch:
do not use any phone in your
building.
Immediately call your gas supplier
from a neighbour's phone. Follow
the gas supplier's instructions.
If you cannot reach your gas
supplier, call the re department.
918-784f
Regency Gem54
Gas Fireplace
12.19.16
Owners &
Installation Manual
www.regency-re.com.au
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
MODELS: GEM54NG1-R
GEM54LPG1-R
GEM54ULPG1-R
LISTINGS AND CODE APPROVALS
These gas appliances have been tested in
accordance with AS4558 / NZS 5262 and
Association for installation and operation
as described in these Installation and
Your unit should be serviced annually
by an authorised service person.
2Gem 54 Regency Gas Fire
To the New Owner:
REGENCY®. The Gem54 has been
®
Gem 54 Regency Gas Fire 3
table of
contents
DATA BADGE
.......................................................4
DIMENSIONS
Unit Dimensions ............................................................5
................5
INSTALLATION
Important Message ......................................................6
............................................................6
............................................6
......................................................7
.........................................7
Clearances ....................................................................8
...................................8
.......................................9
...............................9
Mantel Clearances.......................................................10
Mantel Leg Clearances................................................10
..................................................... 11
..............................13
...............................................13
Nailing Strips........................................................13
.....................................................13
Vent Restrictor Position ...............................................14
............................15
Venting Arrangements ................................................16
...............................16
........................................17
.............17
5” x 8” Rigid Pipe Cross Reference Chart ...................18
Venting Arrangements ................................................20
Allowable Horizontal Terminations.......................20
Venting Arrangements ................................................21
Allowable Horizontal Terminations for Gem54-lpg/
......................................................................21
Venting Arrangements ................................................24
Allowable Vertical Terminations for Gem54-ng ....24
Venting Arrangements ................................................25
Allowable Vertical Terminations for Gem54-lpg/
ULPG ...................................................................25
Unit Installation with Horizontal Termination................26
Unit Installation with Vertical Termination ....................27
Unit Installation............................................................28
High Elevation .............................................................29
Gas Line Installation....................................................29
...........................................................29
..........................................29
S.I.T. Valve Description................................................29
Conversion from NG to LPG .......................................30
Conversion from NG to ULPG.....................................30
....................................................33
Wiring Diagram ...........................................................33
........................................34
..................35
..................................................35
.............35
Log Set Installation......................................................36
....................39
...................................................40
OPERATING INSTRUCTIONS
.................................................42
......................................................................42
......................................................42
...................................................42
.............42
..............................43
.................................................................44
Wiring ..........................................................................46
MAINTENANCE
.............................................47
General Vent Maintenance..........................................47
.........................................47
...............................................................47
Glass Door...................................................................47
Glass Replacement .............................................47
Glass Door Removal ...................................................48
...........................49
........................................49
..............................................50
PARTS LIST
............................................................52
Accessories .................................................................53
WARRANTY
......................................................................54
4Gem 54 Regency Gas Fire
SAFETY LABEL
data badge
NOTE:®
one.
COPY OF DATA BADGE
Electrical: Millivolt Only
Serial
Number 345
918-785c
N2134
Regency Gas Fireplace
Gas Type NG LPG ULPG
Model Gem54NG1-R Gem54LP1-R Gem54ULPG1-R
Gas Consumption 35.9 mj. 32.2mj. 28.7mj.
Manifold Pressure 0.88 kPa 2.49kPa 2.49 kPa
Injector Size 1 x #32 1 x#51 1 x #52
2.95mm 1.70mm 1.61mm
Model
Approval No: AGA 7493 G
Code AS4558 / NZ5262
Part #: 918-785
Rev. C
Colour: Black on Grey
Size: 100%
Sept. 4/08: no changes to artwork
Apr. 30/09: Received certification #
June 10/13: Revised AGA #
Dec. 24/13: Updated E. Aus address and code format
Nov. 9/16: Rev. C - updated naming convention
Distributed by:
Western Australia:
Air Group Australia
28 Division St
Welshpool WA 6106
Eastern Australia:
Fireplace Products
Australia Pty. Ltd.
1 Conquest Way
Hallam, VIC 3803
To be installed by an authorised person in
accordance with installation instructions provided
with the appliance.
909-133
Part #: 909-133
Colour: Black on White.
Size: 7.1” x 1.55” 180mm x 39mm
Mar. 30/09
Apr. 16/12: Changed, removed punctuation and all caps as
per Aus
Warning primarily a
decorative appliance
not certified
as a space heater
Gem 54 Regency Gas Fire 5
DIMENSIONS
dimensions
59 (1499mm)
52-5/8 (1337mm)
48-1/2 (1232mm) 20-1/2 (521mm)
19-3/4 (502mm)
10-5/8
(270mm)
1-1/2
(38mm)
31-5/8 (803mm)
46-3/8 (1178mm)
35-1/4 (895mm)
22-3/8 (568mm)
17-1/8 (435mm)
5-11/16
(144mm)
FACEPLATE & DOOR FRAME OVERLAY DIMENSIONS
UNIT DIMENSIONS
6Gem 54 Regency Gas Fire
installation
13)
14)
15)
IMPORTANT MESSAGE
SAVE THESE
INSTRUCTIONS
to determine the need for a permit prior to
and all applicable codes and complies with a
AS/NZS 5601.
BEFORE YOU START
INSTALLATION AND REPAIR SHOULD
BE DONEBYANAUTHORIZED SERVICE
PERSON. THE APPLIANCE
GENERAL SAFETY
INFORMATION
SHOULD BE INSPECTED BEFORE
USE AND AT LEAST ANNUALLY BY A
PROFESSIONAL SERVICE PERSON.
MORE FREQUENT CLEANING MAY
BE REQUIRED DUE TO EXCESSIVE
LINT FROM CARPETING, BEDDING
MATERIAL, ETC. IT IS IMPERATIVE
THAT CONTROL COMPARTMENTS,
BURNERS AND CIRCULATING AIR
PASSAGEWAYS OF THE APPLIANCE
BE KEPT CLEAN.
DUE TO HIGH TEMPERATURES, THE
APPLIANCE SHOULD BE LOCATED
OUT OF TRAFFIC AND AWAY FROM
FURNITURE AND DRAPERIES.
WARNING: FAILURE TO INSTALL THIS
APPLIANCE CORRECTLY WILL VOID
YOUR WARRANTY AND MAY CAUSE
A SERIOUS HOUSE FIRE.
CHILDRENANDADULTS SHOULD BE
ALERTED TO THE HAZARDS OF HIGH
SURFACE TEMPERATURES, ESPE-
CIALLY THEFIREPLACE GLASS,AND
SHOULDSTAYAWAYTOAVOIDBURNS
OR CLOTHING IGNITION.
YOUNGCHILDRENSHOULDBECARE-
FULLY SUPERVISED WHEN THEY
ARE IN THE SAME ROOM AS THE
APPLIANCE.
1)
Codes.
2) -
codes.
3)
be enclosed.
4)
5)
6) Venting terminals shall not be recessed into
a wall or siding.
7)
be replaced prior to operating the appliance.
8)
9)
10) Be aware of electrical wiring locations in
termination.
11)
operating this appliance.
12)
"THIS UNIT MUST ALWAYS
TERMINATE / VENT
DIRECTLY TO THE OUTDOORS."
CLOTHINGOROTHERFLAMMABLE
MATERIALSHOULDNOTBEPLACED
ON OR NEAR THE APPLIANCE.
NOT INTENDED FOR FIREPLACE
INSERT.
Gem 54 Regency Gas Fire 7
installation
This includes:
1)
2)
CAUTION: Any alteration to the product that
causes sooting or carboning that results
in damage is not the responsibility of the
manufacturer.
LOCATING YOUR
GAS FIREPLACE
A)
B)
C) Recessed into Wall/Alcove
D) Corner
Diagram 1
1)
2)
installed on a metal or wood panel extending
3)
be installed in a recessed position or framed
Diagram 1.
7) -
8)
to the following sections:
Panels
9)
10)
operation fully explained to
customer.
INSTALLATION CHECKLIST
1) Locate appliance
2)
3)
4)
5)
6)
4) This appliance is Listed for bedroom
codes before installation.
5)
6)
clearances and floor protection before
Note: For vent terminations refer to
"Exterior Vent Termination Locations"
section.
8Gem 54 Regency Gas Fire
installation
Caution Requirements
NOT be
WARNING
Fire hazard is an extreme risk
if these clearances (air space) to combustible materials are not
adhered to. It is of greatest importance that this replace and vent
system be installed only in accordance with these instructions.
CLEARANCES
The clearances listed below are Minimum distances unless otherwise stated:
A major cause of chimney related res is failure to maintain required clearances (air space) to combustible materials. It is of the greatest
importance that this replace and vent system be installed only in accordance with these instructions.
F
B
E
D
A
Installed Close
to Floor
G
48" (1219mm)
4"
(102mm) 5-11/16
(144mm)
28
(711mm)
20"
(508mm)
22-1/2
52-5/8
60-1/2" (1537mm)
Non-combustible
Material
Non-combustible Material
Non-combustible
Material
Non-combustible
Material
Metal Stud (header)
Wood Stud
W
ood Stud
Clearance: Dimension Measured From:
A: Mantel Height (min.)
B: Sidewall
C: Ceiling
(room and/or alcove)
D: Mantel Depth (max.)
E: Alcove Width
F: Alcove Depth
Note
F
B
C
Installed Close
to Ceiling
NON-COMBUSTIBLE REQUIREMENTS
Flue Clearances
Horizontal - Top
Horiztonal - Side
Horiztonal - Bottom
Vertical
Gem 54 Regency Gas Fire 9
installation
If finishing the wall above the unit with paint -
the non-combustible board (shipped separately
from the unit) should be installed. Facing board
must be ordered when ordering the unit.
Calcium silicate board is a high - grade material
with cement, quartz, natural and selected
minerals as the main raw materials. It is widely
used for partitions and ceilings in buildings.
It is fire proof and earthquake proof.
If finishing the wall above the unit with materials
such as tile, brick, marble, etc. non-combustible
board available from the building supply store
can be used.
Note: Calcium Silicate is 12mm thick.
Caution: This non-combustible board can be damaged if
dropped or struck. Handle with care.
Inspect board prior to installation. Do not install if cracked.
1) Using plaster board screws - secure non combustible material
around unit, framing and top nailing strip every 150mm.
Important Note: To avoid cracking the board - pre-drill holes prior to
securing to unit/ framing.
2) Wipe any debris/dust from the non combustible
material and drywall.
3) Prior to taping and mudding it is highly recommended
to prime the facing and edges using a quality primer. This will
ensure proper adhesion of both the tape and mud.
The optional board is very porous. During dry fit, ensue that both
surfaces being taped are even.
4) Tape the seams using a mesh type tape.
5) To seal up seams as normal we recommend using a
product called Durabond high strength compound - for the first coat
This product can be found at any hardware store.
Sealant must be cured as per manufacturer’s recommendations.
6) Prime wall for a second time for proper adhesion of paint
7) Paint walls using a high quality paint which will withstand
the high temperatures being emitted from this appliance.
Note: Incorrectly sealed joints may crack. Keep sealant thickness to a
minimum.
4"
(102mm)
22-3/8
(568mm)
20"
(508mm)
21-3/4 (554mm)
52-5/8 (1343mm)
61-1/2" (1537mm)
Non-combustible
Facing Board
Non-combustible Facing Board
Non-combustible Facing Board
Metal Stud (header)
Timber Stud
Timber Stud
Non-combustible Facing Board
61-1/2" (1537mm)
5-5/8
(143mm)
NON COMBUSTIBLE FACING BOARD
NON COMBUSTIBLE FACING INSTALLATION
Non- combustible board
(calcium silicate)
Non-combustible board
MUST BE PRIMED.
Non- combustible board
(calcium silicate)
10 Gem 54 Regency Gas Fire
installation
MANTEL CLEARANCES
Note: Ensure the paint that is used on the mantel
and the facing is "heat resistant" or the
paint may discolour.
MANTEL LEG CLEARANCES
4"
A
llowable mantel
legprojection
11-1/2”(292mm)
14”(356mm)
15-3/4” (400mm)
1.5" (38mm)
MANTEL LEG 4”(102mm) Non-Combustible
Drywall
2
0
12 64
810
Topof
Fireplace
Opening
13" (330mm)
3½" (89mm)
Standoff
Metal Stud
(On Edge)
0
14
Non-combustible
Facing
To Floor
1" (25mm)
30 (762mm)
20
21
28-1/8
(724mm)
(51mm)
(102mm)
(152mm)
(203mm)
(254mm)
(305mm)
(356mm)
Due to the extreme heat this replace emits, the
mantel clearances are critical.
clearances from top of front facing are shown in the
diagram on the right.
Note: A non-combustible mantel may be
installed at a lower height if the framing
is made of metal studs covered with a
non-combustible board.
Gem 54 Regency Gas Fire 11
installation
Note: When constructing the framed opening, please ensure there
is access to install the gas lines when the unit is installed.
2)
-
lation codes. (Do not insulate the replace itself.)
WARNING: Failure to insulate and add vapor barriers to the inside
of the exterior wall will result in operational and performance
problems including, but not limited to: excessive condensation
on glass doors, poor ame package, carbon, blue ames etc.
These are not product related issues.
3)
4)
-
faceplate.
FRAMING & FINISHING
1)
IMPORTANT: Header must be metal stud.
framing materials.
58-3/16 (1478mm)
26-5/8 (676mm)
5)
dimensions noted below must
removal of the faceplate.
Material
Nailing Strip
Position
13mm 25mm
Setting
25mm 13mm
38mm
Unit
Nailing Strip
1 Forward
Unit
Nailing Strip
½ Forward
Unit
Nailing Strip
Flush w/unit
Factory Set
NailingStrips
Nailing strip/
Standoff bracket
12 Gem 54 Regency Gas Fire
installation
A
B
C
D
E
F
G
H
I
J
KL
Non-Combustible
Facing
Metal Stud (Header)
on edge
Metal Stud
(Header)
on edge
(Located on theright side of thefireplace)
Framing
Dimensions Description Gem54
A
B
C**
D
E Corner Wall Length
G Vent Centerline Height
H
I Gas Connection Opening Height
J Gas Connection Height
K Gas Connection Inset
L Gas Connection Opening Width
*
Gem 54 Regency Gas Fire 13
installation
VENTING INTRODUCTION
Note: These ue pipes must not be connected to any other
appliance.
shown below.
1) Remove one screw in location shown below.
2)°
bend in the same direction as the top tabs.
3)
determined.
UNIT ASSEMBLY
PRIOR TO
INSTALLATION
STANDOFF ASSEMBLY
be folded into shape and attached - see diagram 1.
1)
2)
Remove this screw to
strip
Diagram 1
Rear/side
standos
Diagram 2
Nailing Strips
Shipping brackets -
remove after shipped.
NAILING STRIPS
Note: The bottom nailing strip will need to be bent on site and
IMPORTANT NOTE
the side nailing strips set as far forward on
Nailing Strip / Top
Nailing Strips
Diagram 3
14 Gem 54 Regency Gas Fire
installation
1) Remove the glass door.
2) Remove the screws that hold the vent restrictor plate in place.
3)
4)
VENT RESTRICTOR POSITION
Vent Restrictor Settings for Gem54-NG Vent Restrictor Settings for Gem54-LP
Gem54-ULPG
108mm
76mm
51mm
Vent Restrictor Set 1
Vent Restrictor Set 2
Vent Restrictor Set 3
SET 2
THIS
HOLE SETS THE
VENT RESTRICTOR
AT 76mm
SET 1
THIS
HOLE SETS THE
VENT RESTRICTOR
AT 108mm
SET 3
THIS
HOLE SETS THE
VENT RESTRICTOR
AT 51mm
SET 3
THIS HOLE SETS THE
VENT RESTRICTOR
AT 51mm
SET 1
THIS HOLE SETS THE
VENT RESTRICTOR
AT 108mm
SET 4
THIS HOLE SETS THE
VENT RESTRICTOR
AT 25mm
Gem 54 Regency Gas Fire 15
installation
EXTERIOR FLUE TERMINATION LOCATIONS
Minimum clearances required for balanced ue terminals or
the ue terminals of outdoor appliances
according to AS5601-2004 (AGA gas installation code) or NZS 5262 (New Zealand)
and local authorities having jurisdiction.
air at the appliance is achieved.
Clearance 'k' in mm
Space Heaters All Other Appliances
Up to 50 MJ/h
Up to 50 MJ/h
Over 150 MJ/h
150 500 1000 1500
16 Gem 54 Regency Gas Fire
installation
8” dia.
Flue pipe
5” dia. flue pipe
spring spacer
Termination Cap
AstroCap XL TM
(Part #946-623/P)
Vent Guard - if required*
(Part #946-506/P)
Wall Thimble
(Mandatory in all
Horizontal T erminations)
Vinyl Siding
Standoff
VENTING ARRANGEMENTS
HORIZONTAL TERMINATION (FLEX)
Regency®Direct Vent System
FPI Direct Vent (Flex) System Termination Kits include all the
parts needed to install the Gem54 using a exible vent.
Notes:
1) Liner sections should be continuous without any joints
or seams.
2) Only Flex pipe purchased from FPI may be used for Flex
installations.
3) Horizontal vent must be supported every 3 feet (0.9m).
4) A wall thimble is mandatory for all horizontal terminations
due to high temperatures.
FPI Kit # Length Contains:
1)
2)
3) spring spacers
4) thimble
5) AstroCap termination cap
6) screws
7)
8) plated screws
9)
point
10)
Gem 54 Regency Gas Fire 17
installation
RIGID PIPE VENTING SYSTEMS
BASIC HORIZONTAL & VERTICAL TERMINATIONS
component parts for installation of both horizontal
The minimum components required for a basic
Horizontal Termination are:
1 AstroCap XL Termination Cap
1 90oElbow
1 Rigid Pipe Adaptor
1 Wall Thimble
The minimum components required for a basic
Vertical Termination are:
1 Vertical Termination Cap
1 Rigid Pipe Adaptor
penetrate roof
1 Storm Collar
When using Rigid Vent other than
Simpson Dura-Vent, 3 screws must be
used to secure rigid pipe to adaptor.
WARNING:
Do not combine venting components from
XLTM
Rigid Pipe
Adaptor (770-994)
Pipe Length
Vertical Terminal
Storm Collar
Flashing
Ceiling Firestop
Pipe
Length
Pipe Length
90 Elbow
o
AstroCap XL
Termination Cap
(Part #946-623/P)
Wall Thimble
(Mandatory in all
Horizontal Terminations)
Vinyl Siding
Standoff (Optional) Vent Guard-if required*
(Part #946-506/P)
18 Gem 54 Regency Gas Fire
installation
5” X 8” RIGID PIPE CROSS REFERENCE CHART
Adjustable Length 3”-10”-Galvanized N/A N/A
5DAL TC-5DLT
Adjustable Length 3”-10”-Black N/A N/A
5DALB TC-5DLTB
Adjustable Length 11”-14” -Galvanized Disc. - See 58DV-08A 5DT-AJ
N/A N/A
Adjustable Length 11”-14” -Black Disc. - See 58DV-08B 5DT-AJB
N/A N/A
Extension Pipe 17”-24” -Galvanized Disc. - See 58DV-16A N/A
N/A N/A
Extension Pipe 17”-24” -Black Disc. - See 58DV-16AB N/A
N/A N/A
Adjustable Length 8-1/2”-Galvanized 58DVA-08A - N/A from FPI N/A
N/A N/A
Adjustable Length 8-1/2”-Black 58DVA-08AB N/A
N/A N/A
Extension Pipe 16”-Galvanized 58DVA-16A - N/A from FPI N/A
N/A N/A
45ºElbow-Galvanized 58DVA-E45 5DT-EL45
5DT-EL45 TE-5DE45
45ºElbow-Black 58DVA-E45B 5DT-EL45B
5DT-EL45B TE-5DE45B
45ºElbow Swivel-Galvanized Disc. - See 58DVA-E45 N/A
N/A N/A
45ºElbow Swivel-Black Disc.-See 58DVA-E45B N/A
N/A N/A
90ºElbow-Galvanized 58DVA-E90 5DT-EL90S
5DT-EL90S TE-5DE90
90ºElbow-Black 58DVA-E90B 5DT-EL90SB
5DT-EL90SB TE-5DE90B
90ºElbow, Swivel-Galvanized Disc. - See 46DVA-E45 N/A
N/A N/A
90ºElbow, Swivel-Black Disc. - See 46DVA-E45 N/A
N/A N/A
90º Starter Elbow, Swivel-Galvanized N/A N/A
N/A N/A
Adaptor* N/A N/A
N/A N/A
Ceiling Support 58DVA-DC 5DT-CS
5DSP TM-5RDS
Cathedral Support Box 58DVA-CS 5DT-CSS
5DRS TM-5SS
Wall Support/Band 58DVA-WS 5DT-WS/B
5DWS TM-5WS
Offset Support 58DVA-ES - N/A from FPI 5DT-OS
N/A TM-5OS
Wall Thimble-Black 58DVA-WT 5DT-WT
5DWT N/A
Wall Thimble Support/Ceiling Support 58DVA-DC - N/A from FPI N/A
N/A N/A
Firestop Spacer 58DVA-FS 5DT-FS
5DFS TM-5LS
Tr im Plate-Black 58DAV-WFS 5DT-TP
5DCP TM-5TP
5” X 8” RIGID PIPE CROSS REFERENCE CHART
Components from different Manufacturers may not be mixed. Not all rigid pipe components are available directly from Regency.
Note: The listed manufacturers may have other lengths not shown on this chart, which would also be approved.
Description Simpson
Direct Vent Pro®
Selkirk
Direct Temp™
Metal-Fab™
Sure Seal
ICC Excel
Direct
6” Pipe Length-Galvanized 58DVA-06 5DT-6
5D6 TC-5DL6
6” Pipe Length-Black 58DVA-06B 5DT-6B
5D6B TC-5DL6B
9” Pipe Length-Galvanized 58DVA-09 5DT-9
N/A TC-5DL9
9” Pipe Length-Black 58DVA-09B 5DT-9B
N/A TC-5DL9B
12” Pipe Length-Galvanized 58DVA-12 5DT-12
5D12 TC-5DL1
12” Pipe Length-Black 58DVA-12B 5DT-12B
5D12B TC-5DL1B
18” Pipe Length-Galvanized 58DVA-18 5DT-18
5D18 TC-5DL18
18” Pipe Length-Black 58DVA-18B - N/A from FPI 5DT-18B
5D18B TC-5DL18B
24” Pipe Length-Galvanized 58DVA-24 5DT-24
5D24 TC-5DL2
24” Pipe Length-Black 58DVA-24B 5DT-24B
5D24B TC-4DL2B
36” Pipe Length-Galvanized 58DVA-36 5DT-36
5D36 TC-5DL3
36” Pipe Length-Black 58DVA-36B 5DT-36B
5D36B TC-5DL3B
48” Pipe Length-Galvanized 58DVA-48 5DT-48
5D48 TC-5DL4
48” Pipe Length-Black 58DVA-48B 5DT-48B
5D48B TC-5DL4B
60” Pipe Length-Galvanized 58DVA-60 N/A
N/A N/A
60” Pipe Length-Black 58DVA-60B - N/A from FPI N/A
N/A N/A
Gem 54 Regency Gas Fire 19
installation
Description Simpson
Direct Vent Pro®
Selkirk
Direct Temp™
Metal-Fab™
Sure Seal
ICC Excel
Direct
Attic Insulation Shield 12” 58DVA-IS N/A from FPI N/A N/A N/A
High Wind Vertical Cap 58DVA-VCH N/A N/A TM-5VT
High Wind Horizontal Cap N/A N/A N/A TM-5DHT
Horizontal Square Te rmination Cap N/A 5DT-HHC 5DHT TM-5HT
Vertical Te rmination Cap N/A 5DT-HVC 5DVT N/A
Storm Collar 58DVA-SC 5DT-SC 5DSC TM-SC
Restrictor Disk 58DVA-RD N/A N/A TM-5DS
Colinear Flex Connectors N/A N/A N/A N/A
Adjustable Flashing 0/12-6/12 58DVA-F6 5DT-AF6 5DF TF-5FA
Adjustable Flashing 6/12-12/12 58DVA-F12 5DT-AF12 5DF1-2 TF-5FB
Vinyl Siding Standoff 58DVA-VSS 5DT-VS 5DVS TM-VSS
Vinyl Siding Shield Plate N/A 5DT-VSP N/A N/A
Snorkel Te rmination 14” 58DVA-SNK14 N/A N/A TM-5ST14
Snorkel Te rmination 36” 58DVA-SNK36 (N/A - FPI) N/A N/A TM-5ST36
Basic Horizontal Te rmination Kit (A) N/A 5DT-HKA N/A TM-5HTK
Horizontal Te rmination Kit (B) 58DVA-KHA 5DT-HKB N/A TM-5HTK
Vertical Te rmination Kit 58DVA-VHA 5DT-VKC N/A N/A
FPI
946-604/P Simpson Direct Vent or Astro Cap -Vent Guard (Optional) 946-623/P AstroCap XL Horizontal Cap
770-994 Rigid Pipe Adaptor (Must use with all rigid piping) **946-506/P Vent Guard (Optional)
**946-606 Starter collar reducer 5” x 8” to 4” x 6-5/8” 946-625 Vinyl Siding Standoff - AstroCap XL
**Note: When using Metal-Fab Sure Seal Rigid Piping - please note that the Adaptor (4DDA) must be used in conjunction with FPI Rigid Pipe Adaptor (510-994).
** Not available/applicable for the following units: B41XTE, B41XTCE, HZ54E
Offset Pipe Selection: Use this table to determine offset pipe lengths.
Pipe Length
(L)
5” x 8” Venting For specific instructions on venting components - visit the
manufacturers website listed below.
Run (X) Rise (Y)
0” (0mm) 5-11/16” (144mm) 15-5/16” (389mm) Simpson Direct Vent Pro: www.duravent.com
6” (152mm) 8-13/16” (224mm) 18-7/16” (468mm) Selkirk Direct-Temp: www.selkirkcorp.com
9” (229mm) 10-15/16” (278mm) 20-9/16” (522mm) Metal-Fab Sure Seal: www.mtlfab.com
12” (305mm) 13” (330mm) 22-11/16” (576mm) Industrial Chimney Company: www.icc-rsf.com
24” (610mm) 21-7/16” (697mm) 31-1/16” (789mm) Note: Horizontal runs of vent must be level, or have a 1/4”
rise for every 1 foot of run towards the termination.
Never allow the vent to run downward - this could cause high
temperatures and may present a possible fi re hazard.
36” (914mm) 29-13/16” (757mm) 39-7/16” (1002mm)
48” (1219mm) 38-1/4” (972mm) 47-7/8” (1216mm)
20 Gem 54 Regency Gas Fire
installation
VENTING ARRANGEMENTS
ALLOWABLE HORIZONTAL TERMINATIONS
o(two 45o o
Note: Must use optional rigid pipe adapter (Part# 770-994) when using Simpson Duravent Venting Systems.
• Maintain clearances to combustibles as listed in "Clearances" section
• Horizontal vent must be supported every 3 ft / 91 cm.
• Firestops are required at each oor level and whenever passing through a wall.
• A wall thimble is mandatory for all horizontal terminations due to high temperatures.
VENT RESTRICTOR SETTING:
Vent restrictor factory set, no adjustment required unless otherwise indicated.
2
2
0
0
12
12 20
6
6 14
4
44(1118mm)
Minimum Height
Requirement
4
14
8
8 16
10
10 18
Vertical Height (Feet)
Horizontal (Feet)
Vent Restrictor
on Set 2
Vent Restrictor
on Set 3
Vent Restrictor
on Set 1
(factory setting)
16
18
"THIS UNIT MUST ALWAYS
TERMINATE / VENT
DIRECTLY TO THE OUTDOORS."
This manual suits for next models
3
Table of contents
Other Regency Indoor Fireplace manuals
Regency
Regency P36-NG Quick start guide
Regency
Regency Horizon HZ42STE-NG Quick start guide
Regency
Regency Horizon HZ40E Service manual
Regency
Regency PG33-NG Quick start guide
Regency
Regency P121-NG1 Quick start guide
Regency
Regency G51-NG UltraGlow Quick start guide
Regency
Regency HZ54E-NG10 Quick start guide
Regency
Regency U41 Quick start guide
Regency
Regency P33-LP10 Quick start guide
Regency
Regency Contura RC500E Quick start guide
Regency
Regency FireGenie PG121-NG1 Quick start guide
Regency
Regency Z30DVT-LP User manual
Regency
Regency Liberty L965E Service manual
Regency
Regency City Series CB40E Series Datasheet
Regency
Regency F250B Quick start guide
Regency
Regency Bellavista B36X Quick start guide
Regency
Regency Energy E33-NG10 Quick start guide
Regency
Regency Sunrise U32S-NG5 Quick start guide
Regency
Regency E18-NG User manual
Regency
Regency GF900L-NG Quick start guide
Popular Indoor Fireplace manuals by other brands
Ecoflam
Ecoflam AZUR 30 manual
Town & Country Fireplaces
Town & Country Fireplaces TC36 Installation and operating instructions
Osburn
Osburn HYBRID-35 owner's manual
FMI
FMI GMCAT42 Series OWNER'S OPERATION AND INSTALLATION MANUAL
Amantii
Amantii BS1910034-1/EU4 Installation & operation instructions
Jøtul
Jøtul F 118 N Installation instructions with technical data
Security Chimneys International
Security Chimneys International SB36 installation instructions
Woodfire
Woodfire EVO 20 Operation and installation manual
Empire Comfort Systems
Empire Comfort Systems Tahoe DVP36FP30-4NAT Installation instructions and owner's manual
Desa
Desa Comfort Glow LFP33NR OWNER'S OPERATION AND INSTALLATION MANUAL
Napoleon
Napoleon NEFE33-0614AM-1 Installation and operating instructions
Megamaster
Megamaster Lugano Assembly & operating instructions
barkman
barkman Bitsbox quick start guide
Outdoor Lifestyles
Outdoor Lifestyles CARODG36I owner's manual
Napoleon
Napoleon EPI3T installation instructions
Twin-Star International
Twin-Star International 18EF031GRA manual
Spark
Spark SS-36-N Owner's operation and instruction manual
The Outdoor Plus
The Outdoor Plus Olympian 48 manual