Regency I100B-1 BERWICK Quick start guide
Model: I100B-1
Owners &
Installation
PLEASE KEEP THESE INSTRUCTIONS FOR
FUTURE REFERENCE
Manual
Dec-08-2016
918-731f
WARNING:
Improper installation, adjustment, alteration, service or maintenance can
cause injury or property damage. Refer to this manual. For assistance
or additional information consult an authorised installer, service agency
or the distributor.
BERWICK FIREPLACE INSERT
FPI - FIREPLACE PRODUCTS AUSTRALIA PTY LTD.
1 CONQUEST WAY HALLAM VICTORIA 3803
2Regency Berwick Fireplace Insert
Thank-you for purchasing a
REGENCY FIREPLACE PRODUCT.
The pride of workmanship that goes into each of our products will give you years of trouble-free
enjoyment. Should you have any questions about your product that are not covered in this manual,
please contact the REGENCY DEALER in your area.
Keep those REGENCY FIRES burning.
SAFETY NOTE:
about restrictions and installation inspection requirements in your area.
The authority having jurisdiction should be consulted before installation to determine the need to
obtain a permit.
ONLY CLEAN APPLIANCE WITH A DAMP CLOTH
(NEVER WHEN UNIT IS HOT)
DO NOT USE ANY ABRASIVE CLEANERS
DO NOT BURN (WILL VOID WARRANTY):
• Treated wood • Tea Tree • Oil Based woods • Coal • Garbage
• Cardboard • Solvents • Colored Paper • Trash
Save these Instructions
Regency Berwick Fireplace Insert 3
table of
contents
OPERATING INSTRUCTIONS
Operating Instructions .........................................................12
Air Slide Control...................................................................12
..............................................................................12
MAINTENANCE
Creosote..............................................................................13
.......13
Maintenance........................................................................13
Glass Maintenance..............................................................13
Door Latch Adjustment ........................................................13
Wood Storage......................................................................13
PARTS LIST
Heater Assembly .................................................................14
WARRANTY
Warranty ..............................................................................16
Data Badge ............................................................................4
Unit Dimensions ....................................................................5
INSTALLATION
Before Installing Your Insert ...................................................6
Residential Installation ...........................................................6
Safety Guidelines and Warnings ...........................................7
Flue Specifications ................................................................7
Wood Insert Specifications ....................................................7
Brick Installation ....................................................................7
Zero Clearance Dimensions..................................................8
Zero Clearance Box Dimensions...........................................8
Fireplace Clearances .............................................................9
Installation into a Masonry Fireplace ...................................10
Installation into a Factory Built Fireplace .............................10
Faceplate & Fan Installation ................................................11
4Regency Berwick Fireplace Insert
SAFETY LABEL
data badge
This is a copy of the label that accompanies each
the contents here for your review.
NOTE: Regency units are constantly being
improved. Check the label on the unit and if
correct one.
Regency Berwick Fireplace Insert 5
DIMENSIONS
dimensions
6Regency Berwick Fireplace Insert
installation
1) Please read this entire manual before you
to follow instructions may result in property
damage, bodily injury or even death. Be
aware that local Codes and Regulations may
override some items in this manual. Check
with your local inspector.
2) THE APPLIANCE AND FLUE-SYSTEM
SHALL BE INSTALLED IN ACCORD-
ANCE WITH AS/NZS 2918:2001 AND
THE APPROPRIATE REQUIREMENTS
OF THE RELEVANT BUILDING CODE OR
CODES.
APPLIANCES INSTALLED IN ACCORD-
ANCE WITH THIS STANDARD SHALL
COMPLY WITH THE REQUIREMENTS OF
AS/NZS 4013 WHERE REQUIRED BY THE
REGULATORY AUTHORITY.
ANY MODIFICATION OF THE APPLIANCE
THAT HAS NOT BEEN APPROVED IN
WRITING BY THE TESTING AUTHORITY
IS CONSIDERED TO BE IN BREACH OF
THEAPPROVAL GRANTED FOR COMPLI-
ANCE WITH AS/NZS 4013.
RESIDENTIAL
INSTALLATION
Regency Inserts are constructed with the high-
est quality materials and assembled under strict
quality control procedures that ensure years of
trouble free and reliable performance.
It is important that you read this manual thor-
oughly and fully understand the safe instal-
lation and operating procedures. The more
you understand the way your Regency Insert
operates, the more enjoyment you will experi-
ence from knowing that your unit is operating
at peak performance.
BEFORE INSTALLING
YOUR INSERT
1) Please read this entire manual before you
to follow instructions may result in property
damage, bodily injury or even death. Install
and use only in accordance with manufactur-
er’s installation and operating instructions.
2) Check your local building codes - Building
Inspection Department. You may require
a permit before installing your insert. Be
aware that local codes and regulations may
override some items in the manual.
WARNING: Careless installation is the
major cause of safety hazard. Check all
local building and safety codes before
installation of unit.
3) Notify your home insurance company that
heater.
4)
two or more people to move it safely. The
insert can be badly damaged by mishan-
dling.
5)
will become inaccessible once you have
installed your Regency Insert, you should
either remove or secure it in the open posi-
tion.
6) -
ing your insert to determine that it is free
from cracks, loose mortar or other signs of
damage. If repairs are required, they should
be completed before installing your insert.
Do not remove bricks or mortar from your
7) Do not connect the insert to a ue system
servicing another appliance or an air
distribution duct.
CAUTION: MIXING OF APPLIANCE OR
FLUE-SYSTEM COMPONENTS FROM
DIFFERENT SOURCES OR MODIFYING
THE DIMENSIONAL SPECIFICATION OF
COMPONENTS MAY RESULT IN HAZ-
ARDOUS CONDITIONS. WHERE SUCH
ACTION IS CONSIDERED, THE MANU-
FACTURER SHOULD BE CONSULTED
IN THE FIRST INSTANCE.
3)
combustibles to ensure that they are within
the prescribed limits.
4)
instructions. The performance of your wood
when door is open, and even reduced heat
draft which can result in very short burn times
and excessive heat output.
5) -
tible material.
6) Do not connect this unit to a ue serving
another appliance.
Regency Berwick Fireplace Insert 7
installation
BRICK
INSTALLATION
made to extend the life of your heater and to
radiate heat more evenly.
Important: Remove the packing material from
above and below the top bricks. Check to see
have not become misaligned during shipping.
SAFETY GUIDELINES AND
WARNINGS
1) Never use petrol, petrol type lantern fuels,
kerosene, charcoal lighter fuel, or similar
heater. Keep all such liquids well away from
the heater while it is in use.
2) Keep the door closed during operation and
maintain all seals in good condition.
3) Do not burn any quantities of paper, garbage,
petrol, naptha or engine oil in your heater.
4) If you have smoke detectors, prevent smoke
5)
extensive damage to your heater including
warpage and premature steel corrosion.
6) Do not permit creosote or soot build-up in
7) Your Regency heater can be very hot. You
may be seriously burned if you touch the
heater while it is operating, keep children,
clothing and furniture away. Warn children
8) The heater consumes air while operating,
provide adequate ventilation with an air duct
or open a window while the heater is in use.
9) Do not use grates or andirons or other
methods for supporting fuel. Burn directly
on the base or bricks where supplied.
10) Open the draft control fully for 10 to 15
seconds prior to slowly opening the door
11) Do not connect your unit to any air distribu-
tion duct.
12)
-
wood, “mill ends”, etc. is not allowed as this
Evidence of excessive overheating will void
your warranty. As well, a large portion of
sawmill waste is chemically treated timber,
which is illegal to burn in many areas. Salt
13) DO NOT OPERATE WITH BROKEN
GLASS.
FLUE
SPECIFICATIONS
system thoroughly. If in doubt about its condition,
seek professional advice. Your Regency Insert is
The appliance, when installed, must be electrical-
ly grounded in accordance with local codes.
WOOD INSERT
Height
Width
Depth
SPECIFICATIONS
minimum sizes:
8Regency Berwick Fireplace Insert
installation
ZERO CLEARANCE
DIMENSIONS
ZERO CLEARANCE
BOX DIMENSIONS
Important: Non-combustible sheeting of a minimum thickness of 12mm must be used on the front face of the enclosure.
Regency Berwick Fireplace Insert 9
installation
FIREPLACE CLEARANCES
10 Regency Berwick Fireplace Insert
installation
INSTALLATION INTO A
MASONRY FIREPLACE
The insert must be installed as per the require-
ments of your local inspection authority.
Regency highly recommends the use of a full
liner as the safest installation and provides the
most optimum performance. Your retailer should
be able to help you decide which system would
be the best for your application.
The use of this connection method not only
increases the safety of your insert by directing
insert is able to “breathe” better by allowing a
greater draft to be created. The greater draft can
smoking out the door, and dirty glass.
INSTALLATION INTO A
FACTORY BUILT
FIREPLACE
1)
full stainless steel rigid is mandatory, for both
safety and performance purposes. When
breathe better by allowing a greater draft to
be created. The greater draft can decrease
out the door, and dirty glass.
2) -
ing rain cap must be removed from your
should also be removed to allow passage
of the liner.
3) In most cases opening the existing spark
screens fully should give enough room for
the insert installation. If it does not, remove
and store.
4)
shimming is required, use non-combustible
masonry or steel shims.
5) Measure approximately the alignment of the
6) Once the above items have been checked,
-
(Re-install raincap at completion of installa-
tion).
Regency Berwick Fireplace Insert 11
installation
1)
2) Position the faceplate up against the unit by sliding the left side of
the fascia in behind the door hinges and align the 4 screw holes with
FACEPLATE & FAN INSTALLATION
3) Install the fan fascia by aligning the bottom screw locations with the
bottom faceplate. See page 13 for fan wiring diagram.
4) Re-install door.
5) Install the draft plate cover by sliding the tabs into the tab brackets
thru the opening in the draft plate cover.
6) Install knob on damper control rod.
Draft Plate Cover
Damper
Control Rod
12 Regency Berwick Fireplace Insert
operating
instructions
4) After about 45 minutes, when your wood
has begun to burn strongly, adjust your draft
level.
WARNING: Never build a roaring re in
a cold heater. Always warm your heater
up slowly!
5) Once a bed of coals has been established
the draft control to a low setting to operate
6)
rate at a moderate level and avoid a large
operate the heater at its maximum setting,
and only after the metal has been warmed.
7)
expected as the high temperature paint
becomes seasoned. Windows and/or doors
should be left open to provide adequate
ventilation while this temporary condition
exists. Burning the heater at a very high
8) Do not place anything on the heater top
during the curing process. This may result
9)
will increase.
Pull - Open
WARNING: To build a re in ignorance
or to disregard the information con-
tained in this section can cause serious
permanent damage to the unit and void
your warranty!!
AIR SLIDE CONTROL
Both the primary and air wash drafts are control-
led by the control rod located on the right side
of the unit (when facing the unit). To increase
your draft - pull open, and to decrease - push
closed. All units have a secondary draft system
that continually allows combustion air to the
OPERATING
INSTRUCTIONS
With your unit now correctly installed and safety
inspected by your local authority, you are now
the operation of your draft control.
CAUTION: THIS APPLIANCE MUST BE
MAINTAINED AND OPERATED AT ALLTIMES
IN ACCORDANCE WITH THESE INSTRUC-
TIONS.
CAUTION: THE USE OF SOME TYPES OF
PRESERVATIVE-TREATED WOODASA FUEL
CAN BE HAZARDOUS.
WARNING: ANY MODIFICATION OF THE AP-
PLIANCE THAT HAS NOT BEEN APPROVED
IN WRITING BY THE TESTING AUTHORITY
IS CONSIDERED AS BREACHING AS/NZS
4013.
WARNING: DO NOT USE FLAMMABLE
LIQUIDS OR AEROSOLS TO START OR
REKINDLE THE FIRE.
WARNING: DO NOT USE FLAMMABLE LIQ-
UIDS OR AEROSOLS IN THE VICINITY OF
THIS APPLIANCE WHEN IT IS OPERATING.
WARNING: DO NOT STORE FUEL WITHIN
HEATER INSTALLATION CLEARANCES.
WARNING: OPEN AIR CONTROL AND
DAMPER WHEN FITTED BEFORE OPENING
FIRING DOOR.
FIRST FIRE
When your installation is completed and in-
1) Open control fully.
2)
CAUTION: Never leave unit unattended
if door is left open. This procedure is for
re start-up only, as unit may overheat
if door is left open for too long.
3) With the draft still in the fully open position
the door.
Push - Closed
For safety reasons and in order to
avoid over ring of your unit do not
burn your re with the door open
or ajar.
Regency Berwick Fireplace Insert 13
maintenance
10)
drafting problems may occur. Consult an
experienced dealer or mason on methods
of increasing your draft.
11) Some cracking and popping noises may be
experienced during the heating up process.
These noises will be minimal when your unit
reaches temperature.
12) Before opening your door to reload, open
draft fully for approximately 10 to 15 seconds
minimize any smoking.
13) All fuel burning appliances consume oxygen
during operation. It is important that you
supply a source of fresh air to your unit
while burning. A slightly opened window is
created by your Regency Heater causing a
open a window near your unit.
CAUTION: If the body of your unit, ue bae
or any part of the ue connector starts to
glow, you are overring. Stop loading fuel
immediately and close the draft control until
the glow has completely subsided.
14) Green or wet wood is not recommended for
your unit. If you must add wet or green fuel,
open the draft control fully until all moisture
Once all moisture has been removed, the
draft control may be adjusted to maintain
15) If you have been burning your heater on
a low draft, use caution when opening the
door. After opening the damper, open the
before fully opening the door.
16) The controls of your unit or the air supply
passages should not be altered to increase
17) If you burn the unit too slowly or at too low
a setting your unit will not be operating as
says that if your glass is clean, then your
Burn the heater hot enough to keep your
glass clean and you won't need to clean
CREOSOTE
When wood is burned slowly, it produces tar and
other organic vapours, which when combined
with moisture, form creosote. The creosote
WARNING: Things to remember in case
of a ue re:
1. Close all draft and damper controls.
2. CALL THE FIRE DEPARTMENT.
Ways to Prevent and Keep Unit
Free of Creosote
1) Burn heater with the draft control wide open
for about 10-15 minutes every morning
during burning season.
2) Burn heater with draft control wide open
for about 10 - 15 minutes every time you
apply fresh wood. This allows the wood to
achieve the charcoal stage faster and burns
up any unburned gas vapours which might
otherwise be deposited within the system.
3) Only burn seasoned wood! Avoid burning
wet or green wood. Seasoned wood has
been dried at least one year.
4)
smouldering one that can deposit creosote
within the system.
5)
WOOD STORAGE
Store wood under cover, such as in a shed, or
covered with a tarp, plastic, tar paper, sheets
of scrap plywood, etc., as uncovered wood can
absorb water from rain or snow, delaying the
seasoning process.
MAINTENANCE
It is very important to carefully maintain your
season and as necessary during the season, as
creosote deposits may build up rapidly. Moving
parts of your heater require no lubrication. The
door rope seals, and door glass is imperative
for the correct operation and longevity of your
Regency Wood heater. They should be inspected
on a regular basis and replaced if they show any
of these componenets can damage the heater
and void warranty.
inspected at least once every two months
during the heating season to determine if a
creosote buildup has occured.
6) Have ue system and unit cleaned by
competent ue sweeps twice a year dur-
ing the rst year of use and at least once
a year thereafter or when a signicant
layer of creosote has accumulated (3
mm/1/8" or more) it should be removed
to reduce the risk of a ue re.
GLASS MAINTENANCE
Your Regency heater is supplied with Neoceram
ceramic glass that will withstand the highest
heat that your unit will produce. In the event
that you break your glass by impact, purchase
your replacement from an authorized Regency
dealer only, and follow our step-by-step instruc-
tions for replacement.
Allow the heater to cool down before cleaning
the glass, do not clean the glass when it is hot.
Do not use abrasive cleaners.
Rear View of Door shown
Allen Screw
Latching
Sleeve
Set
Screw
DOOR LATCH
ADJUSTMENT
The door latch may require adjustment as the
door gasket material compresses over time.
be moved closer to the door frame, causing a
tighter seal;
1) Unscrew latching sleeve.
2) Remove allen screw.
3) Spin door handle clockwise to desired depth.
4) Re-install allen screw and latching sleeve.
5) Adjust set screw to proper depth to ensure
that the handle does not rotate 360 degrees.
14 Regency Berwick Fireplace Insert
PARTS LIST
parts list
7
6
5
3
4
2
8
1
9
10
12
1) 8010503 Door Assembly (without handle)
2) 8010114 Door Handle Set
3) 1194003 Back Heat Shield
1194007 Top Heat Shield
4) 8010501 Air Slide
8) 8010106 Glass Neoceram W/Gasket
8010104 Secondary Air Tube
(A)
7510206 Cast Plate Set (optional) (B)
9) 8010115 Glass Retainer Bracket
11) 936-233 Door rope seal 5 ft. (not shown)
HEATER ASSEMBLY
Part # Description
Internal Blower Wiring Diagram (240V)
Hot-"Brown”
Neutral-“Blue”
Green-Yellow
Black
Red
Attach to Fan
Ⅰ
Ⅱ
572
210
346
8
570
10
38
A
B
Regency Berwick Fireplace Insert 15
NOTES
notes
16 Regency Berwick Fireplace Insert
WARRANTY
warranty
Revision Date: November 2016
Regency Wood Products Warranty
Limited Warranty
FPI Fireplace Products International Ltd. (“the manufacturer”) through its wholly owned subsidiary, Fireplace
Products Australia Pty Ltd (for Australia and New Zealand customers) and sold under the Regency® brand of
fireplace products (collectively referred to herein as “FPI”), extends this Limited Warranty to the original purchaser
of this appliance provided the product remains in the original place of installation. The items covered by this
limited warranty and the period of such coverage is set forth in the table below.
Some conditions apply (see below).
The policy is not transferable, amendable or negotiable under any circumstances.
Wood Products
Component Coverage Labor
Coverage
Components Covered
15
years
2
years
1
year
Warranty (Years)
Welded Firebox Steel
5
All Stainless Steel Components, Smoke Deflectors,
Heat Shields etc.
1
Air Tubes
1
Airmate
1
Door handle and latch assembly, all hardware
1
Glass Thermal Breakage Only
1
Steel Faceplates, Accessory Housings
1
All Plating
1
Ash Drawer, Heatshields, Pedestal
1
All Baffles-Steel, Ceramic, Vermiculite
1
All castings, firebox, surrounds, doors, panels etc.
1
All Electrical, Fans, wiring, switches etc.
(Fan only)
1
Glass - Crazing
1
Catalyst Assembly (see below for specific details)
6 Years
Prorated
3
Flue components
1
Firebricks
Nil
Nil
After the original warranty coverage for any of the parts above have expired, any repair and/or replacement parts
purchased by the consumer from FPI or through an accredited distributor or dealer will carry a ninety (90) day
warranty (valid only with an original copy of the tax invoice). No labor coverage is included with any repair and/or
replacement part.
Replacement parts are limited to one per warranty term. Airtube and baffle replacements are limited to one
replacement per term.
Catalyst Assembly
IMPORTANT WARRANTY INFORMATION FOR UNITS WITH A CATALYTIC CONVERTER
FPI will replace, at no charge to the consumer, 'one' catalytic converter that ceases to function within three (3)
years from the date of purchase by the original consumer, provided that the following conditions are met:
(1) The catalytic converter must not have been mechanically abused
(2) Only recommended fuels have been used in the appliance
Regency Berwick Fireplace Insert 17
WARRANTY
warranty
Revision Date: November 2016
Regency Wood Products Warranty
If after three (3) years the catalytic converter fails to function, a prorated warranty will provide for replacement at
the following fee schedule to be paid by the consumer*:
Year 4.....................$90*
Year 5.....................$100*
Year 6.....................$110*
* Prices subject to change without notice. Conditions (1) and (2) above also apply for prorated warranty periods.
AFTER YEAR SIX (6), THE CONSUMER MUST PURCHASE ANY CATALYTIC CONVERTERS THAT NEED REPLACEMENT AT
THE CURRENT RETAIL PRICE, AND WILL BE RESPONSIBLE FOR ANY LABOUR COSTS TO REMOVE AND/OR SERVICE.
LABOR WILL ONLY BE COVERED ON THE CATALYTIC CONVERTER FOR THE FIRST THREE (3) YEARS.
Conditions:
Warranty protects against defect in manufacture or FPI factory assembled components only, unless herein
specified otherwise. This warranty will only apply to those products which are acquired at the time of this
warranty being effective. FPI will not be liable for any damage or loss that falls outside the scope of the warranty.
Any part(s) found to be defective during the warranty period as outlined above will be repaired or replaced at FPI’s
option through an accredited distributor, dealer or pre-approved and assigned agent provided that the defective
part is returned to the distributor, dealer or agent for inspection if requested by FPI. Alternatively, FPI may at its
own discretion fully discharge all of its obligations under the warranty by refunding the verified purchase price of
the product to the original purchaser. The purchase price must be confirmed by an original copy of the tax invoice.
The authorised selling dealer, or an alternative authorised FPI dealer if pre-approved by FPI, is responsible for all
in-field diagnosis and service work related to all warranty claims. This warranty does not cover dealer travel
costs for diagnostic or service work. Dealers may charge homeowner for travel and additional time. Check with
your selling dealer in advance for any costs to you when arranging a warranty call. FPI is not responsible for
results or costs of workmanship of unauthorised FPI dealers or agents in the negligence of their service work.
Additional service fees may apply if you are seeking warranty service from a dealer other than the dealer from
whom you originally purchased the product.
At all times FPI reserves the right to inspect reported complaints on location in the field claimed to be defective
and determine whether the warranty will apply prior to processing or authorising of any claim. Failure to allow
this upon request will void the warranty.
All warranty claims must be submitted by the dealer servicing the claim, including an original copy of the tax
invoice (proof of purchase by you). All claims must be complete and provide full details as requested by FPI to
receive consideration for evaluation, including proof of maintenance records. Incomplete claims may be rejected.
FPI has absolute discretion to assess and determine any warranty claim and may accept or reject a claim as it
considers appropriate. Any part or parts of the unit found to be defective will be repaired or replaced at FPI's
option, through an accredited distributor or service agent provided that the defective part be returned to the
distributor or agent, Transportation Prepaid, if requested. It is the general practice of FPI to charge for larger,
higher priced replacement parts and issue credit once the replaced component has been returned to FPI and
evaluated for manufacturer defect.
If a consumer has a unit installed outside an accredited distributor, dealer or pre-approved service agent’s
service area, or the closest approved service agent is situated more than thirty (30) kilometres from the
installation, FPI is not obliged to arrange warranty repairs or shipping/transportation costs. In these cases, the
consumer must arrange warranty service with its selling dealer, and shipping, travel and/or additional labor
charges will apply.
Unit must be installed according to all manufacturers’ instructions as per the manual.
All Local and National required codes must be met.
The installer is responsible to ensure the unit is operating as designed at the time of installation.
18 Regency Berwick Fireplace Insert
WARRANTY
warranty
Revision Date: November 2016
Regency Wood Products Warranty
The original purchaser is responsible for annual maintenance of the unit, as outlined in the owner’s manual. As
outlined below, the warranty may be voided due to problems caused by lack of maintenance. Annual maintenance
records should be retained.
Exclusions:
This Limited Warranty does not extend to paint, rust or corrosion of any kind due to a lack of maintenance or
improper venting, combustion air provision, corrosive chemicals (i.e. chlorine, salt, air, etc.), firebrick (rear, sides or
bottom), door or glass gasket, or any other additional factory fitted gasket.
Malfunction, damage or performance based issues as a result of environmental conditions, location, chemical
damages, downdrafts, installation error, installation by an unqualified installer, incorrect chimney components
(including but not limited to cap size or type), operator error, abuse, misuse, use of improper fuels (such as
unseasoned timber, mill-ends, construction timber or debris, off-cuts, treated or painted timber, tea tree, metal or
foil, plastics, garbage, solvents, cardboard, coal or coal products, oil based products, waxed cartons, compressed
pre-manufactured logs), accidents, lack of regular maintenance and upkeep, acts of God, weather related
problems from hurricanes, tornados, earthquakes, floods, lightning strikes/bolts or acts of terrorism or war, which
result in malfunction of the appliance are not covered under the terms of this Limited Warranty.
FPI has no obligation to enhance or modify any unit once manufactured (i.e. as products evolve, field modifications
or upgrades will not be performed on existing appliances).
Any unit showing signs of neglect or misuse will not be covered under the terms of this warranty policy and may
void this warranty. This includes units with rusted or corroded fireboxes which have not been reported as rusted or
corroded within three (3) months of installation/purchase. Any alteration to the unit which causes sooting or
carboning that results in damage to the exterior fascia or over firing that can cause component or firebox/heat
exchanger failure will not be covered by this warranty.
Units which show evidence of being operated while damaged, or with problems known to the purchaser and
causing further damages will void this warranty.
Units where the serial no. has been altered, deleted, removed or made illegible will void this warranty.
Minor movement, expansion and contraction of the steel is normal and is not covered under the terms of this
warranty.
Freight damages for products or parts are not covered under the terms of the warranty.
Porcelain/Enamel: Absolute perfection is neither guaranteed nor commercially possible. Any chips must be
reported and inspected by the authorised selling dealer within three (3) days of installation. Any damage of this
type not reported after this time period will be subject to rejection and any related warranty will not apply.
Special Finishes: Expect some changes in color as the product "ages" with constant heating and cooling. The
manufacturer warranty does not cover tarnishing, changing colors and/or marks (i.e. finger prints, etc.) after the
purchase of the product. Damage from the use of abrasive cleaners is not covered by warranty.
Products made or provided by other manufacturers and used in conjunction with the FPI appliance without prior
authorisation from FPI may void this warranty.
INCORRECT INSTALLATION IS NOT COVERED BY WARRANTY. A SERVICE OR CALLOUT FEE WILL BE CHARGED IN
THESE CIRCUMSTANCES.
Regency Berwick Fireplace Insert 19
WARRANTY
warranty
Revision Date: November 2016
Regency Wood Products Warranty
Limitations of Liability:
1. Exclusion of implied terms
The customer may have the benefit of consumer guarantees under the Australian Consumer Law. To the maximum
extent permitted by law, all terms, conditions or warranties that would be implied into this Warranty or in
connection with the supply of any goods or services by the supplier under law or statute or custom or international
conventions are excluded.
2. Limitation of liability
(a) To the maximum extent permitted by law and subject to clauses 1 and 3, the supplier’s total liability arising out
of or in connection with its performance or its obligations pursuant to this Warranty, or arising out of or in
connection with the supply of specific goods or services (including pursuant to or for breach of this Warranty,
under statute, in equity or for tort, including negligent acts or omissions) is limited as follows: (i) the supplier shall
have no liability to the customer for any Consequential Loss; (ii) without limiting the effect of clause 2(a)(i), the
supplier’s total aggregate liability for Loss, however arising, shall not exceed the GST exclusive aggregate price paid
by the customer to the supplier for the specific goods or services that gave rise to the Loss in question.
(b) The limitations and exclusions in this sub-clause do not apply to the extent that any Loss is directly attributable
to: (i) the personal injury or death caused by the supplier’s default, breach of this Warranty or negligence; or (ii)
fraud by the supplier.
(c) Each party must take reasonable steps to mitigate any Loss it suffers or incurs.
3. Limitation of liability under Australian Consumer Law Guarantees
(a) To the extent that goods supplied by the supplier are not goods of a kind ordinarily acquired for personal,
domestic or household use and the customer is deemed to be a consumer for the purposes of section 64A of the
Australian Consumer Law, the customer agrees that the supplier’s liability for a failure to comply with a consumer
guarantee that the customer may have a benefit under the Australian Consumer Law (other than a guarantee
under sections 51 (title), 52 (undisturbed possession) and 53 (undisclosed securities)), is limited to, at the option of
the supplier, one or more of the following: (i) replacement of the goods or the supply of equivalent goods; (ii) the
repair of the goods; (iii) the payment of the cost of replacing the goods or of acquiring equivalent goods; or (iv)
equivalent goods; or (v) the payment of the cost of having the goods repaired.
(b) To the extent that services supplied by the supplier are services other than services of a kind ordinarily acquired
for personal, domestic or household use or consumption, the supplier’s liability for failure to comply with a
consumer guarantee that the customer may have the benefit of is limited to, at the option of the supplier: (i) the
supply of the services again; or (ii) the payment of the cost of having the services supplied again.
4. Subject to Change
This Limited Warranty is given at the time of sale and purchase of the relevant fireplace product. The terms of this
Limited Warranty may be amended from time to time by FPI in accordance with changes to business practices,
consumer laws or other legal requirements. The rights and protections granted under the Limited Warranty are
those in force in relation to a fireplace product at the time and in the place of sale of that product, and only those
terms will be applicable in respect of that product.
5. Severability
Any term of this Limited Warranty that is invalid or unenforceable in any jurisdiction is to be read down for the
purposes of that jurisdiction, if possible, so as to be valid and enforceable, and is otherwise capable of being
severed to the extent of the invalidity or unenforceability, without affecting the remaining provisions of this
Limited Warranty or affecting the validity or enforceability of that provision in any other jurisdiction.
6. Definitions
For purposes of clauses 1, 2 and 3:
(a) Consequential Loss means loss of expected savings, loss of use, loss of opportunity, loss of profit, loss of
revenue, increased financing costs, loss arising from delay, or any consequential, special or indirect loss or damage,
whether or not the possibility or potential extent of the loss or damage was known or foreseeable, and whether
arising from a claim under indemnity, contract, tort (including negligence), statute or otherwise.
(b) Loss means any expense, cost or damage of any kind and includes Consequential Loss and a fine or penalty
imposed by a statutory or other authority.
20 Regency Berwick Fireplace Insert
WARRANTY
warranty
Revision Date: November 2016
Regency Outdoor Products Warranty
How to Obtain Warranty Service:
Customers should contact the authorised selling dealer to obtain warranty service. In the event the authorised
selling dealer is unable to provide warranty service, please contact FPI by mail at the address listed below. Please
include your name, address, purchase date, selling dealer, serial #, type of unit, a brief description of the problem,
email and telephone contact information, and a copy of your original tax invoice. A representative will contact you
to make arrangements for an inspection and/or warranty service. (See below for Western Australia and/or New
Zealand)
Please note Fireplace Products Australia Pty Ltd does not provide installation services.
Fireplace Products Australia Pty Ltd
1 –3 Conquest Way
Hallam, VIC
Australia, 3803
Phone: +61 3 9799 7277
Fax: +61 3 9799 7822
To obtain warranty service in Western Australia and/or New Zealand, please contact one of our
authorised distributors in those areas:
Western Australia:
Air Group Australia
28-30 Division St.
Welshpool, WA
Australia, 6106
Phone: (08) 9350 2200
Fax: (08) 9353 4225
New Zealand:
Aber Holdings Ltd
PO Box 10095
Te Rapa, Hamilton
New Zealand, 3241
Freephone: 0800 161 161
Product Registration and Customer Support:
Thank you for choosing a Regency Fireplace. Regency strives to be a world leader in the design, manufacture, and
marketing of hearth products. To provide the best support for your product, we request that you complete a
product registration form at http://www.regency-fire.com.au/Customer-Care/Warranty-Registration.aspx within
ninety (90) days of purchase.
Other manuals for I100B-1 BERWICK
1
This manual suits for next models
2
Table of contents
Other Regency Indoor Fireplace manuals
Regency
Regency I1205S Quick start guide
Regency
Regency Classic F1150 User manual
Regency
Regency Gas Insert E33-LP1 User manual
Regency
Regency IG35-NG Quick start guide
Regency
Regency U31-NG and User manual
Regency
Regency I3100 Installation instructions
Regency
Regency bellavista B36XTCE Quick start guide
Regency
Regency Liberty Gas Fireplace L676-NG1 Quick start guide
Regency
Regency Plateau PTO30CFT User manual
Regency
Regency Liberty L900-1 User manual
Regency
Regency GFI300LNG-R User manual
Regency
Regency B41XTE-NG10 Quick start guide
Regency
Regency Classic I2405M Quick start guide
Regency
Regency Grandview G800EC Series Quick start guide
Regency
Regency GF900C-NG1 Quick start guide
Regency
Regency Panorama P33-10 Quick start guide
Regency
Regency H2100M Quick start guide
Regency
Regency GF900L-NG1 Quick start guide
Regency
Regency Greenfire GF900C Quick start guide
Regency
Regency Panorama P36D Quick start guide
Popular Indoor Fireplace manuals by other brands
Travis Industries
Travis Industries 1250 Insert owner's manual
Archgard
Archgard 27-DVIE22 User's installation, operation and maintenance manual
Valor
Valor Retrofire RF24XBN Installation and owner's manual
Nibe
Nibe Contura 690 Style manual
Trueheat
Trueheat TH36 installation manual
RICHARD LE DROFF
RICHARD LE DROFF 1000 Horizon FV Instructions for installation and use
Empire Comfort Systems
Empire Comfort Systems DVP36FP3 series owner's manual
Planika
Planika Dancing Flames quick start guide
Superior
Superior VRE6036 Assembly, installation and operation instructions
Stellar Hearth Products
Stellar Hearth Products GALAXY Series Installation and operating manual
Napoleon
Napoleon GDS60-1N Installation and operating instructions
Nordpeis
Nordpeis Amsterdam Hjorne installation manual
THERMOROSSI
THERMOROSSI PAIR11 Installation, use and maintenance guide
Allen + Roth
Allen + Roth F12-B-031-071A owner's manual
Quadra-Fire
Quadra-Fire 3100-I owner's manual
hergom
hergom HGB-70 Instructions for installation, use and maintenance
kozy heat
kozy heat Z-42 Installation and operating manual
Sunjoy
Sunjoy L-OF083PST-2 Bel Aire owner's manual