Regency Liberty LRI4E series Quick start guide

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
919-380_a
LRI4E / HRI4E Gas Insert
Owners &
Installation Manual
Tested by:
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
www.regency-re.com
05.04.15
Horizon HRI4E
Liberty LRI4E
- Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other
appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch: do not use any phone in your building.
Leave the building immediately.
• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's
instructions.
• If you cannot reach you gas supplier, call the re department.
- Installation and service must be performed by a qualied installer, service agency or the gas supplier.
WARNING
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious
injury, death, or property damage.
MODELS: LRI4E-NG Natural Gas LRI4E-LP Propane
HRI4E-NG Natural Gas HRI4E-LP Propane

2| LRI4E / HRI4E Direct Vent Gas Insert
|
2
TO THE NEW OWNER
Congratulations! You are the owner of a state-of-the-art Gas Insert by Regency.
The Regency Gas Insert Series of hand crafted appliances has been designed to provide you with all the warmth
and charm of a replace, at the ick of a switch. The models LRI4E / HRI4E of this series have been approved by
Warnock Hersey/Intertek for both safety and efciency. As it also bears our own mark, it promises to provide you
with economy, comfort and security for many trouble free years to follow.
Please take a moment now to acquaint yourself with these instructions and the many features of your
Regency Fireplace.
Horizon HRI4ELiberty Gas
Inserts Benets
Horizon Gas
Inserts Benets
Liberty LRI4E

LRI4E / HRI4E Direct Vent Gas Insert | 3
| 3
table of contents
Brick panel installation.................................................28
Enamel panel installation.............................................29
Glass door removal / installation .................................30
Vignette faceplate with Safety screen installation .......31
3 sided low prole faceplate with
safety screen installation .............................................32
4 sided faceplate with safety screen installation..........33
Spacer installation .......................................................34
Backing plate installation.............................................35
Optional mantel deector installation...........................36
Optional Hearth Trim installation .................................37
Operating Instructions ................................................38
First Fire ......................................................................38
Automatic Convection Fan Operation.........................38
Lighting Procedure ......................................................39
Shutdown Procedure...................................................39
Normal Operating Sounds Of Gas Appliances ............40
Copy Of Lighting Instruction Plate...............................40
Maintenance Instructions............................................41
Door Glass ..................................................................41
Pilot Adjustment...........................................................42
General Vent Maintenance..........................................42
Log Replacement ........................................................42
Glass Gasket...............................................................42
Glass crystal burner removal / installation - HRI4E.....43
Glass Burner Removal ................................................43
Glass Burner install .....................................................43
LRI4E ceramic burner Removal / installation .............44
Fan maintenance - with GTMF remote control............45
Valve replacement .......................................................46
Main Assembly ............................................................48
Vignette faceplate........................................................50
Low prole faceplate....................................................50
Warranty ......................................................................51
Unit dimensions with vignette faceplate ........................4
Unit dimensions with low prole faceplate.....................5
MA Code - CO Detector.................................................8
Important Message ......................................................9
Before You Start ............................................................9
Important Message ....................................................10
For Your Safety............................................................10
Specications ..............................................................10
Gas Pressure Testing ..................................................10
Installation Into A Solid Fuel Burning Fireplace Or
Factory Built Fireplace.................................................10
Before You Start ..........................................................10
Installation Checklist.................................................... 11
Materials Required ...................................................... 11
Minimum Fireplace Dimensions .................................. 11
Minimum Clearances to combustibles.........................12
Gas Connection...........................................................13
Venting.........................................................................13
Flue / vent installation..................................................14
Levelling leg adjustment..............................................15
air shutter Adjustment..................................................16
High Elevation .............................................................17
Gas Line Installation....................................................17
Gas Pipe Pressure Testing ..........................................17
885 S.I.T. Valve Description.........................................17
Proame remote system GTMF with fan
(LRI4E / HRI4E)...........................................................18
Conversion from NG to LP ........................................19
Glass crystal / ceramic spa stone installation..............21
Optional PebbleS / GLASS crystal Installation for
Firebox Base (AROUND BURNER) ............................21
HRI4E optional log set installation...............................23
LRI4E log set installation ...........................................25
Standing pilot ..............................................................27
Heat exchange return..................................................27

4| LRI4E / HRI4E Direct Vent Gas Insert
|
4dimensions
UNIT DIMENSIONS WITH VIGNETTE FACEPLATE
41-5/8"
35-1/8"
22-7/8"
26-1/8"
14-3/4"
24.181
614.20
30"
1-1/8"
21-11/16"
20"
3"
14-7/16"
(762mm)
(550mm)
(27mm)
(1056mm)
(366mm)
(891mm)
(580mm)
(374mm)
(622mm)
(507mm)
(76mm
)
18”
(457mm)

LRI4E / HRI4E Direct Vent Gas Insert | 5
| 5
dimensions
UNIT DIMENSIONS WITH LOW PROFILE FACEPLATE

6| LRI4E / HRI4E Direct Vent Gas Insert
|
6dimensions
UNIT DIMENSIONS WITH 4 SIDED VIGNETTE FACEPLATE

LRI4E / HRI4E Direct Vent Gas Insert | 7
| 7
safety decal
This is a copy of the labels that accompany each LRI4E Gas Insert. We
have printed a copy of the contents here for your review.
NOTE: Regency units are constantly being improved. Check the label on
the unit and if there is a dierence, the label on the unit is the correct one.
For the State of Massachusetts, installation and repair must be done by a plumber or gastter licensed in the Commonwealth of
Massachusetts.
For the State of Massachusetts, exible connectors shall not exceed 36 inches in length.
For the State of Massachusetts, the appliances individual manual shut-o must be a t-handle type valve.
The State of Massachusetts requires the installation of a carbon monoxide alarm in accordance with NFPA 720 and a CO alarm with
battery back up in the same room where the gas appliance is installed.

8| LRI4E / HRI4E Direct Vent Gas Insert
|
8safety decal
This is a copy of the labels that accompany each HRI4E Gas Insert. We
have printed a copy of the contents here for your review.
NOTE: Regency units are constantly being improved. Check the label on
the unit and if there is a dierence, the label on the unit is the correct one.
For the State of Massachusetts, installation and repair must be done by a plumber or gastter licensed in the Commonwealth of
Massachusetts.
For the State of Massachusetts, exible connectors shall not exceed 36 inches in length.
For the State of Massachusetts, the appliances individual manual shut-o must be a t-handle type valve.
The State of Massachusetts requires the installation of a carbon monoxide alarm in accordance with NFPA 720 and a CO alarm with
battery back up in the same room where the gas appliance is installed.

LRI4E / HRI4E Direct Vent Gas Insert | 9
| 9
requirements
5.08: Modifications to NFPA-54, Chapter 10
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for
residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than
seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall
be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is
installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shallobserve that a battery
operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure
served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of
qualified licensed professionals for the installation of hard wired carbon monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon
monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of
thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight
(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The
sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL
OBSTRUCTIONS".
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation
unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR
5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by
the Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or
structure used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the
instructions provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, butidentifies
"special venting systems", the following requirements shall be satisfied by the manufacturer:
1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and
2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions,
all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipmentat the completion of
the installation.
MA Code - CO Detector
(for the State of Massachusetts only)

10 | LRI4E / HRI4E Direct Vent Gas Insert
|
10 installation
IMPORTANT MESSAGE
SAVE THESE
INSTRUCTIONS
The LRI4E / HRI4E Gas Inserts must be installed in
accordance with these instructions. Carefully read
all the instructions in this manual rst. Consult the
"authority having jurisdiction" to determine the need
for a permit prior to starting the installation. It is the
responsibility of the installer to ensure this replace
is installed in compliance with manufacturers
instructions and all applicable codes.
BEFORE YOU START
Safe installation and operation of this appliance
requires common sense, however, we are required
by the Canadian Safety Standards and ANSI
Standards to make you aware of the following:
CLOTHING OR OTHER FLAMMABLE
MATERIAL SHOULD NOT BE PLACED
ON OR NEAR THE APPLIANCE.
CHILDREN AND ADULTS SHOULD BE
ALERTED TO THE HAZARDS OF HIGH
SURFACE TEMPERATURES, ESPE
CIALLY THE FIREPLACE GLASS, AND
SHOULD STAY AWAY TO AVOID BURNS
OR CLOTHING IGNITION.
INSTALLATION AND REPAIR SHOULD
BE DONE BY AN AUTHORIZED
SERVICE PERSON. THE APPLIANCE
SHOULD BE INSPECTED BEFORE
USE AND AT LEAST ANNUALLY BY A
PROFESSIONAL SERVICE PERSON.
MORE FREQUENT CLEANING MAY
BE REQUIRED DUE TO EXCESSIVE
LINT FROM CARPETING, BEDDING
MATERIAL, ETC. IT IS IMPERATIVE THAT
CONTROL COMPARTMENTS, BURNERS
AND CIRCULATING AIR PASSAGEWAYS
OF THE APPLIANCE BE KEPT CLEAN.
DUE TO HIGH TEMPERATURES, THE
APPLIANCE SHOULD BE LOCATED
OUT OF TRAFFIC AND AWAY FROM
FURNITURE AND DRAPERIES.
WARNING: FAILURE TO INSTALL THIS
APPLIANCE CORRECTLY WILL VOID
YOUR WARRANTY AND MAY CAUSE A
SERIOUS HOUSE FIRE.
YOUNG CHILDREN SHOULD BE CARE
FULLY SUPERVISED WHEN THEY ARE
IN THE SAME AREA AS THE APPLI
ANCE. TODDLERS, YOUNG CHILDREN
AND OTHERS MAY BE SUSCEPTIBLE
TO ACCIDENTAL CONTACT BURNS. A
PHYSICAL BARRIERS IS RECOMMEND
ED IF THERE ARE AT RISK INDIVIDUAL
IN THE HOUSE. TO RESTRICT ACCESS
TO A FIREPLACE OR STOVE, INSTALL
AN ADJUSTABLE SAFETY GATE TO
KEEP TODDLERS, YOUNG CHILDREN
AND OTHER AT RISK INDIVIDUALS OUT
OF THE ROOM AND AWAY FROM HOT
SURFACES.
A BARRIER DESIGNED TO REDUCE
THE RISK OF BURNS FROM THE HOT
VIEWING GLASS IS PROVIDED WITH
THIS APPLIANCE AND SHALL BE
INSTALLED FOR THE PROTECTION
OF CHILDREN AND OTHER ATRISK
INDIVIDUALS
IF THE BARRIER BECOMES DAMAGED,
THE BARRIER SHALL BE REPLACED
WITH THE MANUFACTURER'S BARRIER
FOR THIS APPLIANCE.
ANY SAFETY SCREEN, GUARD, OR
BARRIER REMOVED FOR SERVICING
AN APPLIANCE MUST BE REPLACED
PRIOR TO OPERATING THE APPLIANCE.