Regency City Series User manual

City Series CV50E Direct Vent Gas Fireplace | 1
City Series CV50E Direct Vent Gas Fireplace
MODEL CV50E-NG CV50E-LP
Fuel Type Natural Gas Propane
Minimum Supply Pressure 5” W.C. (1.25 kPa) 11” W.C. (2.73 kPa)
Manifold Pressure - High 3.8” W.C. (0.94 kPa) 10.5” W.C. (2.62 kPa)
Manifold Pressure - Low 1.1” W.C. (0.27 kPa) 2.9” W.C. (0.72 kPa)
Orice Size -Altitude 0-4500 ft # 36 DMS # 52 DMS
Minimum Input
Altitude 0-4500 ft. (0-1372m)
19,000 Btu/h
(5.56 kW)
17,000 Btu/h
(4.98 kW)
Maximum Input
Altitude 0-4500 ft. (0-1372m)
35,000 Btu/h
(10.25 kW)
33,000 Btu/h
(9.66 kW)
Vent Sizing 5” Inner / 8” Outer 5” Inner / 8” Outer
CSA P.4.1. 57.49% 60.55%
Dimensions
Note: Height Dimension is taken with leveling legs fully inserted and may vary depending on the height of the leveling legs, when unscrewed or extended.
Dimensions will appear as (inches)" / (metric) mm throughout this manual. The inches are rounded to the nearest 1/16" when converted, when greater
accuracy is required, use the metric dimensions.
Note: These units are non-load bearing.
ALL PICTURES / DIAGRAMS SHOWN THROUGHOUT THIS MANUAL ARE FOR ILLUSTRATION PURPOSES ONLY. ACTUAL PRODUCT MAY
VARY DUE TO PRODUCT ENHANCEMENTS.
18"
457mm
10 3
16
"
258mm
13 3
8
"
340mm
54 3
8
"
1382mm
37"
940mm
20 15
16
"
532mm
11 7
8
"
301mm
9 1
8
"
231mm
49 3
16
"
1249mm
8"
203mm
5"
127mm
8 1
2
"
216mm
45 7
8
"
1165mm
PAGE 7
DIMENSIONS
20-7/16''
(519 mm)
NOTE: This model comes with a 5” inner and 8” outer collar (127 mm x 203 mm) which must be reduced to 4” inner x 6-5/8” outer
(102 mm x 168 mm) in all applications when used as a power vent system. See power vent manual for details.

2 | City Series CV50E Direct Vent Gas Fireplace
Gas Connection - Bottom of Unit
Gas Connection - Side of Unit
10 1
4
"
261mm
49 1
16
"
1246mm
8 11
16
"
221mm
1 15
16
"
50mm
1 11
16
"
42mm
FRONT OF UNIT
BACK OF UNIT
OPEN BOTTOM
1 1
2
"
38mm
1 3
16
"
30mm
3 3
4
"
95mm
9
16
"
15mm
16 1
8
"
409mm
1 1
2
"
38mm
1 3
16
"
30mm
16 1
8
"
409mm
3 3
4
"
95mm
9
16
"
15mm
LEFT SIDE
RIGHT SIDE
PAGE 8
Gas Connection - Bottom of Unit
Gas Connection - Side of Unit
10 1
4
"
261mm
49 1
16
"
1246mm
8 11
16
"
221mm
1 15
16
"
50mm
1 11
16
"
42mm
FRONT OF UNIT
BACK OF UNIT
OPEN BOTTOM
1 1
2
"
38mm
1 3
16
"
30mm
3 3
4
"
95mm
9
16
"
15mm
16 1
8
"
409mm
1 1
2
"
38mm
1 3
16
"
30mm
16 1
8
"
409mm
3 3
4
"
95mm
9
16
"
15mm
LEFT SIDE
RIGHT SIDE
PAGE 8
Gas Connection - Bottom of Unit
Gas Connection - Side of Unit

City Series CV50E Direct Vent Gas Fireplace | 3
Electrical Connection - Bottom of Unit
Electrical Connection - Side of Unit
2 3
8
"
60mm
12 3
8
"
314mm
5 3
4
"
145mm
1 1
2
"
38mm
1 3
16
"
30mm
10 1
4
"
261mm
49 1
16
"
1246mm
8 11
16
"
221mm
1 15
16
"
50mm
1 11
16
"
42mm
FRONT OF UNIT
BACK OF UNIT
OPEN BOTTOM
RIGHT SIDE
ELECTRICAL CONNECTIONS
PAGE 9
Electrical Connection - Bottom of Unit
Electrical Connection - Side of Unit
2 3
8
"
60mm
12 3
8
"
314mm
5 3
4
"
145mm
1 1
2
"
38mm
1 3
16
"
30mm
10 1
4
"
261mm
49 1
16
"
1246mm
8 11
16
"
221mm
1 15
16
"
50mm
1 11
16
"
42mm
FRONT OF UNIT
BACK OF UNIT
OPEN BOTTOM
RIGHT SIDE
ELECTRICAL CONNECTIONS
PAGE 9
Electrical Connection - Bottom of Unit
Electrical Connection - Side of Unit

4 | City Series CV50E Direct Vent Gas Fireplace
Clearances
Note: The clearances listed below are minimum distances unless otherwise stated.
A major cause of chimney-related res is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance
that this replace and vent system be installed only in accordance with these instructions.
Flue Clearances to Combustibles
Horizontal - Top 3" (76 mm)
Horizontal - Side 2" (51 mm)
Horizontal - Bottom 2" (51 mm)
Vertical 2" (51 mm)
Passing through wall/
floor/ceiling - when
restop is used.
1-1/2" (38 mm)
Note: This appliance uses 5" x 8" (127 mm x 203
mm) venting for the Non Power Vent.
28 | City Series CV60E
installation
Clearances CV60E
The clearances listed below are Minimum distances unless otherwise stated:
A major cause of chimney related fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this
fireplace and vent system be installed only in accordance with these instructions.
Clearance: single sided Dimension Measured From:
A1: :Mantel Height (min.) ** Top of Fireplace Opening
A: From Floor 10 1/4” (260 mm)" Bottom of Fireplace Opening
B: Sidewall (on one side) 8" (203mm) Side of Fireplace Opening
C: Enclosure width 65 11/16" (1668mm) Side of Fireplace Opening
D: Mantel Depth (max.) **
E: Alcove Width 109.5” (2781mm) Sidewall to Sidewall (Minimum)
F: Alcove Depth 35" (889mm) Front to Unit (Maximum)
H: Convection Air Outlet *180 square inches
G: Convection Air Outlet Opening Oset *0-2" (0-51mm)
K: Minimum clearance to celing 1 3/4” (44 mm)
M:Clearance to Sprinkler Head (Min.) 36" (914mm) Perpendicular
From back wall to chase front
from chase grill
Hearth 0" hearth required
** See mantel clearances chart in this manual.
Flue Clearances to Combustibles
Horizontal - Top 3"
Horizontal - Side 2"
Horizontal - Bottom 2"
Vertical 2"
Passing through wall/
floor/ceiling - when 1-1/2"
Note: This appliance uses 5" x 8" venting.
Alcove
F
D
A1
B
A
J
G
H
L
*A minimum of 180 square
inches of open area, not
lower than 0-2" from top of
enclosure, required for all
installations
Side view
M
Chase grill
Sprinkler
J: Opening Height 18" (457 mm) Bottom/Top of Fireplace Opening
Top of chase to ceiling
20-5/16" (516mm)I: Framing depth
From base of unit to ceiling81 1/4" (2038 mm)L: Ceiling height
E
Alcove
Clearance Dimension Measured From:
A1: Mantel Height (min.) ** Top of Fireplace Opening
A: From Floor (min.) 10-3/16" (462 mm) Bottom of replace opening
B: Sidewall (on one side) min. 5" (127 mm) Side of replace opening
B1: Sidewall (on one side) min. 24" (610 mm) Side air outlet to side wall (min.)
C: Enclosure Width (min.) 54-3/8" (1381 mm) Side of replace opening
D: Mantel Depth (max.) **
E: Alcove Width 92" (2337 mm) Sidewall to sidewall (minimum)
F: Alcove Depth 35" (889 mm) Front to unit (maximum)
G: Convection Air Outlet Opening Oset
(min.)
H: Convection Air Outlet
*0-2" (0-51 mm)
*152 in2(981 cm2)
Max. oset from top of chase enclosure
I: Framing Depth (min.) 20-7/16" (519 mm) From back wall to chase front
J: Opening Height 18" (457 mm) Bottom/top of replace opening
K: minimum clearance to ceiling 1-3/4" (44 mm) Top of chase to ceiling
L: Chase Enclosure (min.) 62-7/8" (1597 mm) From base of unit/oor to top of enclosure
M:Clearance to Sprinkler Head (min.) 36" (914mm) Perpendicular from chase grill
Ceiling Height 81-1/4" (2064 mm) From base of unit/oor to top of alcove
Hearth 0" No hearth required
** See mantel clearances chart in the manual.
28 | City Series CV60E
installation
Clearances CV60E
The clearances listed below are Minimum distances unless otherwise stated:
A major cause of chimney related fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this
fireplace and vent system be installed only in accordance with these instructions.
Clearance: single sided Dimension Measured From:
A1: :Mantel Height (min.) ** Top of Fireplace Opening
A: From Floor 10 1/4” (260 mm)" Bottom of Fireplace Opening
B: Sidewall (on one side) 8" (203mm) Side of Fireplace Opening
C: Enclosure width 65 11/16" (1668mm) Side of Fireplace Opening
D: Mantel Depth (max.) **
E: Alcove Width 109.5” (2781mm) Sidewall to Sidewall (Minimum)
F: Alcove Depth 35" (889mm) Front to Unit (Maximum)
H: Convection Air Outlet *180 square inches
G: Convection Air Outlet Opening Oset *0-2" (0-51mm)
K: Minimum clearance to celing 1 3/4” (44 mm)
M:Clearance to Sprinkler Head (Min.) 36" (914mm) Perpendicular
From back wall to chase front
from chase grill
Hearth 0" hearth required
** See mantel clearances chart in this manual.
Flue Clearances to Combustibles
Horizontal - Top 3"
Horizontal - Side 2"
Horizontal - Bottom 2"
Vertical 2"
Passing through wall/
floor/ceiling - when 1-1/2"
Note: This appliance uses 5" x 8" venting.
Alcove
E
F
D
A1
B
A
J
G
H
L
*A minimum of 180 square
inches of open area, not
lower than 0-2" from top of
enclosure, required for all
installations
Side view
M
Chase grill
Sprinkler
J: Opening Height 18" (457 mm) Bottom/Top of Fireplace Opening
Top of chase to ceiling
20-5/16" (516mm)I: Framing depth
From base of unit to ceiling81 1/4" (2038 mm)L: Ceiling height
*A minimum of 152 square
inches of open area, not
lower than 0-2" from top
of enclosure, required for
all installations.
L
Chase grill
Sprinkler
Side view
M
Caution Requirements
The top, back and sides of the replace are
dened by standos. The metal ends of
the stando may NOT be recessed into
combustible construction.
WARNING
Fire hazard is an extreme risk
if these clearances (air space) to
combustible materials are not adhered
to. It is of greatest importance that this
replace and vent system be installed only
in accordance with these instructions.
When installed as a power vent, the venting
must be reduced to 4" inner x 6-5/8" outer
(102 mm x 168 mm) in all applications. See
required reducers required in this manual if
using rigid/ex pipe.

City Series CV50E Direct Vent Gas Fireplace | 5
Clearances
Floor to ceiling with top opening.
Full framing with low vents in front or 2 sides. Full framing with vents in front or 2 sides.
Full framing with vents in front, 2 sides, or top.
The ventilation opening may only be placed above, on both sides and in front as shown above.
Ventilation grills can never be placed behind the appliance.

6 | City Series CV50E Direct Vent Gas Fireplace
Mantel Clearances
Combustible mantel clearances from top of front facing are shown in the diagram below.
Mantel Leg Clearances
Combustible mantel leg clearances as per diagram:
32 | City Series CV60E
installation
Mantel Clearances
Combustible mantel clearances from top of front facing are shown in the diagram on the right.
Mantel Leg Clearances
Combustible mantel leg clearances as per diagram:
212 6 4810
0
14
9”
(229mm)
18”
(457mm)
10
20
26
Top of
Fireplace
Opening
12” (305mm)
1/2” (13 mm) Drywall, wood, wood panel, etc.
5-1/4”
(133mm)
To Bottom of
Fireplace
Opening
12” (305 mm)
Allowable mantel
MANTEL LEG
leg projection
9” (229 mm)
10” (254 mm)
5”
(127mm)
7”
(178 mm)
12” (305 mm)
MANTEL LEG
9” (229 mm)
10” (254 mm)
5”
(127mm)
7”
(178 mm)
Allowable mantel
leg projection
49-3/16” (1249 mm)
32 | City Series CV60E
installation
Mantel Clearances
Combustible mantel clearances from top of front facing are shown in the diagram on the right.
Mantel Leg Clearances
Combustible mantel leg clearances as per diagram:
212 6 4810
0
14
9”
(229mm)
18”
(457mm)
10
20
26
Top of
Fireplace
Opening
12” (305mm)
1/2” (13 mm) Drywall, wood, wood panel, etc.
5-1/4”
(133mm)
To Bottom of
Fireplace
Opening
12” (305 mm)
Allowable
mantel
MANTEL LEG
leg projection
9” (229 mm)
10” (254 mm)
5”
(127mm)
7”
(178 mm)
12” (305 mm)
MANTEL LEG
9” (229 mm)
10” (254 mm)
5”
(127mm)
7”
(178 mm)
Allowable mantel
leg projection
49-3/16” (1249 mm)

City Series CV50E Direct Vent Gas Fireplace | 7
Framing Dimensions
NOTE: Framing may be constructed of combustible material (i.e. 2 x 4/2 x 6) and does not require steel studs.
Framing
Dimensions Description CV50E
A Framing Height 2 x 4 : 44-3/4" (1137 mm)
2 x 6 : 51-7/8" (1318 mm)
B* Framing Width 54-3/8" (1381 mm)
C* Framing Depth 20-7/16" (519 mm)
D Minimum Height to Combustibles 62-7/8" (1597 mm)
E Corner Wall Depth 66" (1676 mm)
F Corner Facing Wall Depth 93-3/8" (2372 mm)
G Vent Centerline Height 45-3/4" (1162 mm)
** See manual for alternate Gas/ Electrical connection options
Note: A combined minimum of
152 square inches of open area
is required for the convection
air outlet to cool the enclosure.
Ensure clearances for convec-
tion air outlets are met.
See clearances in this manual
for dierent ways to achieve
this.
Note: This appliance must be
installed on a solid surface
such as a plywood oor which
must be the full width and
depth of the appliance.
The lift handles add approximately 4 inches to the width of the appliance. If the appliance will be lifted o the ground and slid into the framed opening,
we suggest changing the framing width from 54-3/8" (1381 mm) to 58-3/8" (1483 mm) to allow the appliance to slide into position with the handles on,
or creating a platform in front of the framed opening where the lift handles can be removed prior to installation. If the framing is raised o the ground you
can install it after the appliance is in place with handles removed to maintain the framing width of 54-3/8" (1381 mm). Ensure that the wood base for the
appliance is strong enough to support its shipping weight of 480 pounds.
| City Series CV60E
installation
Framing Dimensions CV60E
NOTE: Framing may be constructed of combustible material (ie. 2 x 4)and does not require steel studs.
Framing
Dimensions Description CV60E
A Framing Height 44 3/4" (1137mm)
B Framing Width 65 11/16" (1668mm)
C Framing Depth 20-5/16" (516mm)
D Minimum Height to Combustibles 81 1/4"(2038mm)
E Corner Wall Depth 73 7/16” (1866mm)
F Corner Facing Wall Width 103 7/8" (2638mm)
G Vent Centerline Height 58 3/16" (1478mm)
I Gas Connection Opening Height See gas connection location in this manual
See gas connection location in this manual
See gas connection location in this manual
See gas connection location in this manual
J Gas Connection Height
K Gas Connection Inset-Centre Opening
L Gas Connection Opening Width
Note: A combined mini
mum
of 180 square inches of
open
area is required for the
con-
vection air outlet to cool
the
enclosure. Ensure cleara
nces
for Convection Air Outl
ets
are met.
See clearances CV60E
in this
manual as there are di
erent
methods as to how this
can
be achieved.
Note: This appliance must
be
installed on a solid sur
face
such as a plywood
oor
which must be the full
width
and depth of the applianc
e.
With the lift handles adding approximately 4 inches to the overall width of the appliance,In cases where the appliance would need tobe raised o the ground
in order to slide it into the framed opening, it is suggested that either the framing width change 65 11/16 to 69 11/16 “ so appliance could be easily slid into
position with the handles remaining on the appliance, or alternatively create a platform in front of the framed opening where the lift handles could be removed
prior to sliding the appliance into its final position. Alternatively, If raised o the ground, the framing could be installed afterwards once appliance has been
put into place and handles removed in order to keep framing width at 65 11/16”.. Ensure that the wood base that the appliance will sit on is strong enough
to support the full weight of this appliance. The overall weight of this appliance is 480 pounds (shipping weight).
*
*
* The framing depth/width does not take into account drywall/wood or similar materials against the back /side wall.
The framing depth will need to change based on the thickness of the material.
Example: B - 54-3/8" framing width +1/2" drywall per side = 55-3/8")
Example: C - 20-7/16" framing depth +1/2" drywall = 20-15/16")

8 | City Series CV50E Direct Vent Gas Fireplace
Chase Vent Installation Part #482-991 (White)
920-705 06.08.23
1
CITY SERIES
CV/CB50 CHASE VENT INSTALLATION (WHITE FRONT)
Max 2” (51 mm)
Ceiling Ceiling
Top of chase enclosure
Max 2” (51 mm)
Stud
Stud
Stud
Stud
51-1/2” (1308 mm)
Chase Vent
Opening for vent
3”-3-1/2”
(76 mm - 89 mm)
Min 51-1/2”
(1308 mm)
51-1/2” (1308 mm)
Chase Vent
Framed opening must be between 3” (76 mm) and 3-1/2” (89 mm) tall, and at least 51-1/2” (1308 mm) wide to
accomodate the chase vent.
The top of the chase vent opening must be 2”(51 mm) or less from the top of the chase enclosure.
In this application, both the ange and screws to secure the chase vent are exposed as this chase vent is designed to be installed after the nished facing
has been placed on the wall.
Framing Opening must be between 3'' (76 mm) and 3-1/2'' (89 mm) tall, and at least 51-1/2'' (1308 mm) wide to accomodate the Chase vent.
The top of the chase vent opening must be 2'' (51 mm) or less from the top of the chase enclosure.

City Series CV50E Direct Vent Gas Fireplace | 9
16 1
2
"
419mm
2 X 4 STUD
23 3
8
"
594mm
2 X 6 STUD
2"
51mm
MAX. TO
TOP OF
ENCLOSURE
34 11
16
"
881mm
MIN.
62
7
8
"
1597mm
MIN.
28 3
16
"
716mm
152 sq.in MIN.
CHASE VENT OPENING
Screws must not
penetrate unit more
than 1/2".
Adhere to "No Screw"
zones painted on unit
Glue can be used
as an alternative
2X4 OR 2X6 STUD
FLUSH INSTALL
34 11
16
"
881mm
MIN.
51
4
"
133mm
MAX. DEPTH
MANTLE
See Mantel clearance in manual
62 7
8
"
1597mm
MIN.
MAX DEPTH 36" (914 MM)
HEARTH
152 sq.in MIN.
CHASE VENT OPENING
RECESSED INSTALL
Typical Installations
Flush Install Recessed Install

10 | City Series CV50E Direct Vent Gas Fireplace
Note: The TV mounting bracket cannot be secured directly to the appliance. It must be secured to framing. The TV depicted in the picture
may need to be higher depending on the style of TV mounting bracket used.
23 3
8
"
594mm
MAX.
2"
51mm
TO TOP OF
ENCLOSURE
62 7/8"
[1597 mm]
MIN.
MAX. 2X6 STUD
Screws must not
penetrate unit
more than 1/2".
Adhere to "No Screw"
zones painted on unit.
Glue can be used as an alternative
152 sq.in MIN.
CHASE VENT OPENING
MAX.
2"
51mm
TO TOP OF
ENCLOSURE
16 1
2
"
419mm
MIN.
62 7/8"
[1597 mm]
MIN.
34 11/16"
[881 mm]
MIN.
152 sq.in MIN.
CHASE VENT OPENING
MAX. 2X4 STUD
Screws must not
penetrate unit
more than 1/2".
Adhere to "No Screw"
zones painted on unit.
Glue can be used as an alternative
Typical Installations
Maximum TV Recess Flush TV with Hearth