Regency Gas Insert E33-LP1 User manual

aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
aaaaa
L
aaaaaaaaaa
a
aaaaaaaa
a
a
aaaaaaaa
a
a
aaaaaaaa
a
a
aaaaaaaa
a
a
aaaaaaaa
a
aaaaaaaaaa
M
J
K
N
E33 Gas Insert
Model E33-NG1 E33-LP1
Fuel Type Natural Gas Propane
Minimum Supply Pressure 5” W.C. (1.25 kPa) 12” W.C. (2.99 kPa)
Manifold Pressure - High 3.8” W.C. (0.95 kPa) 11” W.C. (2.74 kPa)
Manifold Pressure - Low 1.1” W.C. (0.27 kPa) 2.9” W.C. (0.72 kPa)
Orifice Size -Altitude 0-4500 ft. #31 DMS #50 DMS
Minimum Input
Altitude 0-4500 ft. (0-1372m)
20,000 BTU/h
(5.86 kW)
19,000 BTU/h
(5.57 kW)
Maximum Input
Altitude 0-4500 ft. (0-1372m)
38,000 BTU/h
(11.14 kW)
35,500 BTU/h
(10.40 kW)
Vent Sizing 3” Co-linear 3” Co-linear
Minimum Fireplace Dimensions
The minimum fireplace dimensions for the FPI gas fireplace insert are
shown in the following diagrams:
Dimension Description Contour Faceplate
J Height 24-3/16” (614mm)
K Width 32-1/4” (819mm)
L Depth 17” (432mm)
M Max. Lintel Bar Depth 8” (203mm)
N Rear Width 25” (635mm)
A
C
B
H
D
G
F
E
30°
Dimension Description E33
A Faceplate Width 45-9/16” (1157mm)
B Faceplate Height 31-1/8” (791mm)
C Unit Width 32-1/4” (819mm)
D Unit Height 23-13/16” (605mm)
E Unit Depth 16-3/4” (426mm)
F Faceplate to Vent Centerline 11-1/4” (286mm)
G Faceplate Depth 1-3/8” (35mm)
H Height to Vent Collar 23” (583mm)
I Optional or Standard Front Depth N/A
E33 Gas Insert
Approved Venting Systems
Flex Vent Systems: FPI AstroCap™ Flex Vent
127June 2007 Regency Product Specifications Book
Gas Inserts
Gas Inserts

Clearances
Unless otherwise stated the clearances listed below are Minimum
distances to combustible materials. Please Note: A major cause
of chimney related fires is due to a failure to maintain required
clearances (air space) to combustible materials. It is of the greatest
importance that this fireplace and vent system be installed only in
accordance with these instructions.
Combustible Mantels
Because of the extreme heat this fireplace emits, the mantel
clearances are critical. Combustible mantel clearances from top of
the louvers are shown in the diagram below. Mantel may be installed
anywhere in the shaded area or higher.
Note: A non-combustible mantel may be installed at a lower
height.
Note: Ensure the paint that is used on the mantel and the facing
is “heat resistant” or the paint may discolour.
Clearances to Combustibles
Dimension Description E33
A* From Unit to Side Walls 8” (203mm)
B From Unit to Ceiling 47” (1194mm)
C Minimum Mantel Height 15” (381mm)
D Maximum Mantel Depth 12” (305mm)
E Alcove Width 76” (1930mm)
F Alcove Depth 36” (914mm)
G Hearth Height 1-¼” (32mm)
H Hearth Width 45-½” (1156mm)
I Hearth Depth 13” (330mm)
* Alcove side wall must have a minimum of 8” (203mm) clearance on one side.
25" (635mm)
to floor
Side View
12" (305mm) Mantel
3-1/2" (89mm) Mantel
20”
(508mm)
47”
(1194mm)
to ceiling
15”
(381mm)
2
0
12 64
810
2
0
12
6
16
4
14
8
18
20
10
Top of
Unit
Flush Front Mantel Clearances
Full Screen Door Mantel Clearances
E33 Gas Insert
D
128 June 2007 Regency Product Specifications Book
Gas Inserts
Gas Inserts