Reiner jetStamp 1025 User manual

jetStamp 1025
EN
Short instruction

1
jetStamp 1025
Originalanleitung

2
jetStamp 1025

7
jetStamp 1025
The display depends on the respective menu context. The starting screen of the main
menu is displayed.
For the setting functions (see “Online help of the PCset graphic software”).
fTo activate Bluetooth, press the home button , select Bluetooth , set active and
confirm (see “Online help for the PCset graphic software”).
Display and Buttons Fig. F
1
Trigger button
2
Display
3
On/O button
4
Operating status LED
5
Function key for print cartridge
6
Flap for battery print cartridge
compartment
7
Print carriage
8
Print cartridge
9
Seal
10
Seal retaining clip
11
Seal tip
Operating elements
12
Indicators of print position
13
Print area
14
Charging indicator
15
Connection socket for mains adapter
16
Jack socket for external trigger
17
Micro USB socket
18
SD card slot
19
Battery compartment
20
Locking battery compartment
21
Locking print cartridge
22
Print cartridge contacts
23
Nozzles print cartridge
Important Notes
Before commissioning of the jetStamp 1025, always read the operating instructions and
in particular the safety notes with care. This prevents mistakes in handling of the marking
device and connected safety risks to keep you safe and avoid damage to the device.
Detailed operating instructions and further information can be found in the online help
of the PCset graphic software or on the enclosed USB stick.
a Header with the number of the set imprint
bSet imprint
cMenu bar with menu items and commands
dFour pushbuttons
Home
Scrolling
Back button
Select

8
jetStamp 1025
GB
Safety Notes
WARNING Possible blinding in case of contact between ink and eyes.
fNever hold the jetStamp 1025 with its nozzles pointing at the face of persons!
CAUTION Possible tripping and damage to the device from device lines placed freely in
the room. Place the device lines so that they do not pose any danger source!
Health risks if ink is swallowed.
fDon’t swallow! Keep cartridge out of the reach of children!
NOTICE Damage to the device due to improper transport. Only use packaging that
provides protection from impact and shock to the device!
Damage to the device by moisture.
fBefore commissioning, wait until device has reached room temperature and is completely
dry!
Safety Notes on Rechargeable Batteries
Rechargeable batteries are subject to wear. A longer service life than six months cannot be
warranted.
WARNING Possible explosion at contact with fire.
fDo not forcefully open rechargeable batteries. Do not expose rechargeable batteries to
severe heat. Do not expose rechargeable batteries to extremely low barometric pressures.
CAUTION Injuries from destruction of rechargeable battery jacket when using unsuit-
able rechargeable batteries or non-rechargeable batteries.
fUse only rechargeable batteries intended for the device! Only use the supplied AC adapter
to charge the batteries. Only use rechargeable batteries type nickel metal hydride
(NiMH), REINER item number: 946 192 - 000) of build AA. Always replace all flat recharge-
able batteries at once. Unauthorized batteries may cause damage or malfunction. Observe
polarity of batteries when inserting, see symbols or Fig. G!
Disposal
Defective or flat batteries
Flat batteries of rechargeable batteries must not be disposed of in the household
waste.
Electrical and electronic waste devices
Waste devices must not be disposed of in the conventional household waste. They
must be returned to a special collection point for recycling of electrical and electro-
nic devices.

9
jetStamp 1025
1. Preparation and Taking into Operation
1.1. Commissioning
The rechargeable batteries must be charged completely before the first use.
The charging time is approx. 3 hours. The rechargeable batteries are charged when the
green charge display
14
goes out.
Only connect the device to the PC after the PCset graphic software has been installed,
otherwise the installation of the device drivers will fail!
Inserting rechargeable batteries Fig. B+ C+
Always replace all rechargeable batteries at once. Date, time and counter reading of the
numbering machine are retained when the rechargeable batteries are removed.
fOpen the flap for battery and print cartridge compartment
6
.
fPush battery compartment locking
20
upwards until the locking can be opened.
fOpen battery compartment
19
, ensure correct polarity and insert batteries.
fClose battery compartment
19
.
fClose flap for battery and print cartridge compartment
6
.
Charge the rechargeable batteries Fig. B
fConnect the power supply unit of the device to the socket for power supply unit
15
. Green
charging indicator
14
is lit. The charging process is completed as soon as the charging
indicator goes out.
Inserting printing cartridge Fig. B+ E+ C
Depending on ink type used, dierent Protective Nozzle Seals are required.
Use sealing of the enclosed printing cartridge.
fSwitch the unit on via the ON/OFF button
3
.
The operating status LED
4
lights up green.
fPress function key for print cartridge
5
. Print carriage
7
moves to the right into the
change position.
fOpen flap for battery and print cartridge compartment
6
.
fPush the print cartridge locking
21
slightly upwards and open it.
fRemove the print cartridge
8
from the packaging and remove the dust cover (see operat-
ing instructions for the print cartridge P5).
fPlace the unit on a firm surface.
fHold pressure cartridge locking
21
in place.
G

10
jetStamp 1025
GB
fInsert print cartridge
8
. Make sure that it snaps into place and close the locking of the
pressure cartridge
21
.
fClose flap for battery and print cartridge
6
.
fInstall a new seal
9
into the device, holding the retaining clip of the seal in place
10
.
fInsert seal tip
11
into the notch.
fPress the seal
9
slightly down until it snaps into place in the holder.
fPress function key for print cartridge
5
. Print carriage
7
returns to the basic position.
The change position can also be controlled via the display.
1.2. Install PCset graphic Software
Installation is only possible with administrator rights on the computer.
fInsert installation medium (USB stick or CD) in your PC.
fIf the installation programme does not start up automatically, start the file “setup.exe”.
fObserve the installation programme instructions.
1.3. Firmware update
The most up to date firmware for the jetStamp 1025 can be downloaded from the
REINER website (www.reiner.de).
1.4. Recognising and Removing Interferences
For more information, see the online help of the PCset graphic software, or the enclosed USB.
Contact
Ernst Reiner GmbH & Co. KG
Baumannstr. 16
78120 Furtwangen/Germany
Phone: [phone]
Email: [e-mail]
www.reiner.de
© 2020 Ernst Reiner GmbH & Co. KG
All rights reserved. Translation, reprint and other reproduction of these operating
instructions, even in parts and no matter the form, shall require our express written consent.
We reserve the right to make content changes to these operating instructions without notice.

Technical modifications reserved | PC-1030088-000 F | 12.2020