Reliable Pantman F1 User manual

Model: F1
PANTMAN
USER MANUAL

IMPORTANT SAFEGUARDS
When using an electric appliance, basic precautions should always be followed,
including the following:
WARNING: DANGER OF SCORCHING
Read all instructions before using this pant press to reduce the risk of fire, electric
shock, or injury.
This product is designed for domestic use only.
ØDo not use outdoors.
ØDo not leave your pant press unattended while switched on. Turn off the
switch and unplug the electrical cord when not in use. To unplug, grasp the
plug, not the cord.
ØDo not allow to be used as a toy. Close attention is necessary when used near
children, pets or plants.
ØThe appliance is not intended for use by any children or infirm persons without
supervision.
ØChildren should be supervised to ensure that they do not play with the
appliance.
ØDo not immerse the pant press into water or other liquids.
ØDo not use with damaged cord or plug. If unit is not working as it should, has
been dropped, damaged, left outdoors, or immersed into liquid, contact a
licensed service technician for assistance.
ØDo not pull or carry by cord, use cord as a handle, close a door on the cord, or
pull cord around sharp edges or corners. Keep cord away from heated surfaces.
ØDo not use extension cords or outlets with inadequate current carrying capacity.
ØDo not handle or use this unit while hands are wet.
ØUse only as described in this manual. Operating unit in any way other than
recommended may result in damage to unit or injury to operator.
ØDo not disassemble unit or attempt to make any repairs yourself. Incorrect
assembly or repair could result in a risk of fire, electric shock, or injury to
persons when operating.
Østore your pant press in a cool, dry place. Allow unit to cool completely, and
loop power cord loosely around unit before storing.
2

F1 pant press product information
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
Power Indicator Light
On Button
Safety chain
Press board bar
Press board
Front pressing plate
Foot
Cord wrap
Cord
Plug
Support
3
SAVE THESE INSTRUCTIONS
Placement for watch keys etc.

ASSEMBLYINSTRUCTIONS
Accessories
A. Attach the support to the foot.
B. Insert the attached screws into each hole in foot, and tighten them securely with
screwdriver.
4

5
OPERATING INSTRUCTIONS
A. To open the front pressing plate
Pull the press board bar to open the front pressing plate slowly. The press
board bar will hold the front pressing plate in an open position.
B. How to insert the pants
1. Place the cuffs or bottoms of legs of trousers or pants as far down as
possible between the front pressing plate and the press board. The waistline
of the pants should be hung over the top edge of the front pressing plate.
2. Tidy up the slack of pants.
3. Make sure to place the pants in the middle of the front pressing plate, with
the side seam (as indicated in Figure 3.) aligned with the groove (in the
padding - figure not shown) in the front pressing plate.

C. To close the front pressing plate
nd st
1. Pull the press board bar to the 2 step ( 1 step is for thick trousers or pants).
2.Hold the waistline of the pants and gently pull upwards. This will smooth
out any wrinkles and ensure that pants or trousers are lying flat between the
front pressing plate and press board.
3. Pull the press board bar down firmly until the front pressing plate is fully
locked into the closed position.
* Pull the pants upwards once again.
6
D. Plug the cord into the power socket.The power indicator light will illu-
minate, and the press will startautomatically
E. The press will automatically shut off when the job is completed, and the power
indicator light will also go off. To restart the pressing, press the "on" button,
the power indicator light will illuminate again and start the pressing cycle.

TROUBLESHOOTING GUIDE
Below is a chart detailing the most common problems, their causes and solutions.
Prior to troubleshooting, isolate the unit by removing the cord from the power socket.
Unit fails to operate
properly.
Unit fails to heat up.
Unit is not plugged in.
Unit is damaged
or malfunctioning.
Plug into electric socket
and make sure the power
indicator light is on.
Please contact a
licensed technician.
Unit is not plugged in.
The press board has
been damaged or is
malfunctioning.
Plug into electric socket.
Immediately stop use
and let the unit cool
down completely.
Contact a licensed
technician.
PROBLEM CAUSE SOLUTION
7

Reliable Corporation
5-100 Wingold Avenue
Toronto, Ontario
Canada M6B 4K7
www.reliablecorporation.com
P 416 785 0200
F 416 785 7038
TF 800 268 1649
[email protected]