Remington PRECISION HC7110AU User manual

2 YEAR WARRANTY HC7110AU
PRECISION
HAIRCUT KIT
To register your product go to
www.remington-products.com.au
www.remington.co.nz
USE & CARE
MANUAL
PLEASE READ
PRIOR TO USE

IMPORTANT SAFETY INSTRUCTIONS
When using an electric appliance, basic safety precautions should
always be observed, including the following. Read all instructions
before using this hair clipper.
KEEP POWER ADAPTOR AWAY FROM WATER
WARNING – TO REDUCE THE RISK OF BURNS, FIRE, ELECTRIC
SHOCK OR INJURY TO PERSONS:
• Do not reach for an appliance that has fallen into water.
Unplug it immediately.
• Do not use while bathing or in the shower.
• Do not place or drop into water or other liquid.
• Do not place or store this appliance where it can fall or be pulled into a
bath or sink.
• Except when charging, always unplug this appliance from the electrical
outlet immediately after using.
• This appliance is for household use only.
• This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible
for their safety. Keep the appliance and the power cord away from the
edge of table or countertops and out of reach of children and persons
with reduced physical, sensory or mental capabilities.
• This appliance is not a toy. Children shall be supervised to ensure they
do not play with this appliance.
• Use this appliance only for its intended use as described in this
manual.
• Do not use attachments not recommended by Remington.
• Keep the cord away from heated surfaces.
• Never operate this appliance if it has a damaged cord or plug, if it is
not working properly, if it has been dropped or damaged, or if it has
been dropped into water. If any of these things happen, return the
appliance to an authorised service centre for examination and repair.
• Never drop or insert any object into any of the appliance’s openings.
• Do not use outdoors or operate where aerosol (spray) products are
being used, or where oxygen is being administered.
2

• Make sure the cord is disconnected from the hair clipper while storing
this appliance and cord in a moisture-free area. Do not store it in
temperatures exceeding 60°C (140°F)
• Do not use this appliance with a damaged or broken cutter unit, as
injury may occur. Always make sure blades are aligned properly.
• Always attach plug to appliance and then the adaptor to the outlet. To
disconnect, turn all controls to OFF, then remove adaptor from outlet,
then detach power cord from the hair clipper for storage.
• Do not use an extension cord or a voltage converter with this
appliance.
• Do not wrap the cord around the appliance.
Remington strongly recommends that an approved Safety Switch
(residual current device) be installed to protect all bathroom
power outlets. Ask an electrical contractor for advice.
SAVE THESE INSTRUCTIONS
3

HC7110AU PRECISION HAIRCUT KIT
USE & CARE INSTRUCTION MANUAL
Thank you for purchasing your new Remington®Precision Haircut Kit. Inside
this manual you will find tips on using and caring for your hair clipper.
KEY PARTS
1. Stainless Steel Blade
2. On/Off Switch
3. Charging Indicator Light
4. Adjustable Comb (1-21mm)
5. Adjustable Comb (24-44mm)
Also Includes:
• Barbers Scissors
• Barbers Comb
• Lubricating Oil
• Cleaning Brush
• Power Adaptor
1
2
4
5
3
4

ABOUT YOUR HAIR CLIPPER
HC7110AU Specifications
Power System Cord/Cordless (Rechargeable)
Initial Charge Time 24 Hours
Full Charge Time 18 – 20 Hours
Run Time 40 Minutes
Indicators Charging
Voltage Type Single
Power System: Cord/Cordless – can be used with or without the power
cord.
Charging Indicator: red light that glows when the hair clipper is being
charged.
Voltage Type: Single – 220-240V only.
CHARGING YOUR HAIR CLIPPER
Cordless Use
• Before using your hair clipper for the first time, charge it for 24 hours.
• Ensure the product is switched off.
• Connect the charging adaptor to the product and then to the mains.
The charging LED light will display on the clipper.
• If the product is not going to be used for an extended period of time
(2-3 months), unplug it from the mains and store.
• Fully recharge your hair clipper when you would like to use it again.
• It is not recommended to use this hair clipper directly from the power
outlet when it has been fully charged, however, while using the hair
clipper in cordless mode if there is a noticeable drop in power, you can
use the hair clipper directly from the power outlet.
• To preserve the life of your batteries, let them run out every six months
then recharge for 24 hours.
Corded Use
• Connect the charging adaptor to the product and then to the mains.
• When the cord is connected to the mains, a charging LED light is
displayed on the hair clipper.
Caution: Extended mains (corded) only use will result in the reduction of
the battery life. 5

HOW TO USE
Before Starting to Cut
1. Inspect the hair clipper making sure it is free from hair and dirt.
2. Ensure that the hair is thoroughly dry and tangle free.
3. The blades on your hair clipper should be oiled before every haircut.
Lubricating the Hair Clipper Blades
Simply place a few drops of oil on the teeth of the blades. Use only the light
grade oil supplied or a suitable alternative like sewing machine oil. Only
this type of oil is suitable for the blades on your Remington hair clipper. Do
not use hair oil, grease or any oil mixed with kerosene or any solvent as the
solvent will evaporate and leave a thick oil, slowing the blades.
If oil is not applied to the blades or only a small amount of oil is applied,
this may cause cutting problems. Blades will wear prematurely and not cut
properly if they are not sufficiently lubricated. There may also be a pulling
sensation on the hair.
Instructions for Hair Cutting
Note: For even cutting, allow the trimmer comb/blade to cut its way through
the hair. Do not force it through quickly. If you are cutting for the first time,
start with the maximum length trimmer comb, until you know how short
you would like your hair to be.
Note: The comb guide lengths described for use in the steps below are an
example only, if you want a longer or shorter hair cut you will need to adjust
the comb guide lengths to suit your requirements.
To Attach a Comb
• Hold the comb with its teeth upward.
• To attach a comb, align the legs of the comb with the holes in the
top of the clipper on each side of the blade and slide the legs into the
trimmer until they click.
• To remove, firmly pull the comb straight up away from the clipper.
6

Comb Settings
• The hair clipper comes with two adjustable combs, a short length
adjustable comb (indicated by 1-21mm on the back of the comb) and a
longer length adjustable comb (indicated by 24-44mm on the back of
the comb).
Shorter Length Adjustable Comb Longer Length Adjustable Comb
1mm 24mm
3mm 26mm
6mm 29mm
9mm 32mm
12mm 35mm
15mm 38mm
18mm 41mm
21mm 44mm
Step 1 – Nape of the neck
• Set the comb to 3mm or 6mm.
• Hold the clipper with the blade teeth pointing upwards. Start at the
centre of the head at the base of the neck.
• Slowly lift the clipper, working upwards and outwards through the hair,
trimming just a little at a time.
Step 2 – Back of the head
• With the comb set at 12mm or 18mm, cut the hair at the back of the
head.
Step 3 – Side of the head
• With the comb set at 3mm or 6mm, trim sideburns. Then change to
the longer 9mm guide comb and continue to cut the top of the head.
Step 4 – Top of the head
• Use the longer length comb attachment and set it to 24mm or 27mm
then cut hair on top of the head against the direction in which the hair
normally grows.
• For longer hair on top, use the longer length comb attachment (24 –
44mm) to achieve the desired style.
• Always work from the back of the head.

Step 5 – The finishing touches
• Use the clipper without an attachment comb for close trimming around
the base and sides of the neck.
• To produce a clean straight line at the sideburns, reverse the hair
clipper.
• Place the reversed clipper at right angles to the head so the tips of the
blades lightly touching the skin and then work downwards.
CLEANING & MAINTENANCE
• Your clipper is fitted with high quality blades.
• To ensure long lasting performance of your clipper, clean the blades
and unit regularly.
• Always keep the attachment guide comb on the trimmer blade.
After Each Use
• Ensure the appliance is switched off and unplugged from the mains
before cleaning.
• Brush the accumulated hair from the blades and body of the clipper.
Do not submerge the clipper in water.
• To clean unit, wipe with a damp cloth and dry immediately.
• Place a few drops of cutter or sewing machine oil onto the blades.
Wipe off excess oil.
Every Six Months
• Remove the 2 screws retaining the fixed blade with a screwdriver.
• Remove the blade set.
• Brush out hairs from between the blades with a soft cleaning brush.
Do not remove the lubricating grease from the blades. It is not
necessary to remove the small moving blade from the unit.
• If the moving blade has been removed this can be re-fitted by slotting
the moving blade holder over the pin in the centre of the interior
product head.
• The groove on the moving blade just below the teeth should rest on
the plastic pressure arm which rides inside the groove. The fixed blade
should be assembled with the bevelled edge of the 2 screw holes
facing outward and fixed with screws.
• Note that if the blades are not correctly aligned then cutting efficiency
will be impaired.

Storage
When not in use, unplug the hair clipper and store it out of reach of children
in a safe dry place. Never wrap the cord around the hair clipper as this will
cause the cord to wear prematurely and break. Handle the cord carefully
for long life and avoid jerking, twisting or straining especially at the plug
connections.
BATTERY DISPOSAL
Note: The battery is not intended to be removed or replaced under normal
use. The only time the battery should be removed or the unit opened or dis-
assembled, is at the end of the product’s useful life before it is discarded.
• The HC7110AU contains a nickel metal hydride battery. Once the hair
clipper has reached the end of its life, to ensure proper disposal of the
product, please take the appliance to a recycling centre, where the
internal rechargeable battery should be removed by a professional and
recycled separately.
• For more information about recycling of electrical and battery operated
appliances, please contact your local council office or your household
waste disposal service.
Caution: Do not put in the fire or mutilate your batteries when disposing as
they may burst and release toxic materials. Do not short circuit as it may
cause burns.
7

This product is not suitable to use in a bath or shower.
This product conforms to radio frequency interference requirements.
Any product purchased and used commercially carries a limited 90 Day Warranty.
8