Amantii SYM-34 User manual

INSTALLATION AND OPERATION INSTRUCTIONS FOR
SYM-
34
SYM-
42
SYM-
50
SYM-
60
SYM-
74
SYM-
88
SYM-
100
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE
1
INSTALLATION AND OPERATION INSTRUCTIONS FOR
34
42
50
60
74
88
100
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE
INSTALLATION AND OPERATION INSTRUCTIONS FOR
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE

2
TABLE OF CONTENTS
Please read and carefully follow all of the instruction found in this manual. Please pay
special attention to the safety instructions provided in this manual. The instructions included
here will assure that you have many years of dependable and enjoyable service from your
Amantii product.
IMPORTANT INSTRUCTIONS ......................................................................................................................................... 3
UNPACKING AND TESTING APPLIANCE ................................................................................................................... 7
PLUG INSTALLATION ...................................................................................................................................................... 6
LOCATING THE FIREPLACE ........................................................................................................................................... 7
SYM-34 .................................................................................................................................................................................. 8
SYM-42 ..................................................................................................................................................................................
SYM-50 ................................................................................................................................................................................ 10
SYM-60 ................................................................................................................................................................................ 11
SYM-74 ................................................................................................................................................................................ 12
SYM-88 ................................................................................................................................................................................ 13
SYM-100 .............................................................................................................................................................................. 14
INSTALLATION-WALL MOUNT ................................................................................................................................. 15
INSTALLATION- BUILT-IN ........................................................................................................................................... 16
INSTALLATION- SEMI-FLUSH BUILT-IN .................................................................................................................. 20
MEDIA OPTIONS .............................................................................................................................................................. 24
DECORATIVE MEDIA INSTALLATION ...................................................................................................................... 24
OPERATION ....................................................................................................................................................................... 25
MANUAL OPERATION ................................................................................................................................................... 25
REMOTE CONTROL OPERATION ................................................................................................................................ 26
REPLACEMENT PARTS .................................................................................................................................................. 30
EXPLODED VIEW ............................................................................................................................................................ 32
TRUBLE SHOOTING ........................................................................................................................................................ 33
SERVICE HISTORY .......................................................................................................................................................... 34
WARRANTY ...................................................................................................................................................................... 35
CARE AND MAINTENANCE .......................................................................................................................................... 2

3
IMPORTANT INSTRUCTIONS
Please read the following instructions carefully before using the appliance.
Caution - Fire, electric shock, physical injury and material damage hazards:
To use the appliance, always follow the instructions for assembly, use and maintenance as well as
usage cautions:
1. Carefully read and retain these instructions.
2. Before connecting the appliance, be sure that the mains voltage available matches that specified
on the rating plate.
3. Do not use the appliance for other than its intended use. For domestic indoor use only.
4. There may be trace of odour during the first few minutes of initial use. This is normal and will
quickly disappear.
5. The heater is hot when in use. To avoid burns, do not let bare skin touch any hot surface.
6. Keep combustible material such as furniture, cushions, bedding, paper, clothes, curtains etc. at
least 1m away from the heater.
7. Do not use the heater in areas where flammable liquids are stored or where flammable fumes
may be present.
8. Do not cover or obstruct any of the heat outlet grilles or the air intake openings of the heater.
9. Do not use the heater in the rooms with explosive gas or while using inflammable solvents,
varnish or glue.
10. Keep the heater clean. Do not allow any objects to enter any ventilation or exhaust opening as
this may cause electric shock, or fire or damage to the heater.
11. Always unplug or disconnect the appliance from the mains power supply when not in use or
when moving or cleaning it. Do not pull the cord to unplug the heater.
12. Do not immerse the cord, plug or any part of the appliance in water or any other liquid.
13. Do not attempt to repair, disassemble or modify the appliance. There are no user-serviceable
parts inside.
14. The heater must not be located immediately below a socket-outlet.
15. Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
16. CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this
appliance must not be supplied through an external switching device, such as a timer, or
connected to a circuit that is regularly switched on and off by the utility.
17. Do not use this heater with a programmer, timer, separate remote-control system or any other
device that switches the heater on automatically, since a fire risk exists if the heater is covered or
positioned incorrectly.
18. WARNING: In order to avoid overheating, do not cover the heater.
19. WARNING! – DO NOT COVER THIS APPLIANCE WITH ITEMS SUCH AS CLOTHING, BLANKETS OR
PLACE NEXT TO CURTAINS OR NET/BLINDS.
20. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
21. Do not use this heater in small rooms when they are occupied by persons not capable of leaving

4
the room on their own, unless constant supervision is provided.
22. If the glass is damaged, do not use the heater in order to avoid a hazard.
23. Children of less than 3 years should be kept away from unless continuously supervised.
24. Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided
that it has been placed or installed in its intended normal operating position and they have been
given supervision or instruction concerning use of the appliance in a safe way and understand the
hazards involved, Children aged from 3 years and less than 8 years shall not plug in, regulate and
clean the appliance or perform user maintenance.
25. CAUTION Some parts of this product can become very hot and cause burns. Particular attention
has to be given where children and vulnerable people are present.
26. This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall
not be made by children without supervision.
27. The heater may emit a slight, harmless odour and smoke when first used. This odour and smoke
is normal and it is caused by the initial heating of internal heater parts and will not occur again.
28. DO NOT plug into an extension lead/cable or plug adaptor.
29. DO NOT cut off the plug and hardwire directly into the mains or via a fused fixed spur.
30. For details about installing the fireplace, please refer to “Installation” section.

5
Cautions
Do’s
 Always install the heater in accordance with this guide. If in doubt obtain
expert advice.
 Always make sure the electrical socket is accessible and located adjacent
to but not above the heater.
 Always disconnect the heater from the electrical supply before moving it or
carrying out cleaning maintenance.
 Always make sure the heater is firmly secured to prevent it from being
tipped over.
 Always use a fireguard when young children and infirm persons can come
into contact with the heater.
Don’ts
 Never leave children unsupervised in a room where the heater is ON and
unguarded.
 Never obstruct or cover the fan outlet or force items into heater openings.
 Never install or use the heater anywhere where water is in use i.e.
Bathroom Kitchens Shower Rooms and Swimming Pool etc.
 Never use aerosols or steam cleaners on or around the heater.
 Never route the mains supply cable under carpet etc.
 Never install the heater close to curtains or combustible materials.
 Never use the heater to dry clothes etc.
 Never sit or stand on the heater.
 Never use with a timer or any other device that switches the fire on
automatically.

Your power cord will come separate from the unit, please locate it when unpacking your
fireplace. The plug contained inside the box is predetermined at the factory and according to
orders placed by authorized dealers.
Available are U , European & Swiss plugs. Should you require any of these options please
contact your dealer for purchase. You will be required to give them the correct part number
as listed below.
Please following the instructions to correctly install the plug into your fireplace.
1. Included in the box will be a power cord similar to the one pictured below. See Picture 1.
2. Hold the male plug and insert it into the female receptacle. The receptacle is locate on
the left side if the fireplace.
3. Please make sure the plugs are firmly connected. See Picture 2 above.
PLUG INSTALLATION
UK plug European plug Swiss plug
10103060E 10103030E 10103109E
Picture 1 Picture 2
6

UNPACKI
NG AND TESTING APPLIANCE
Carefully remove the appliance from the box.
Prior to installing the appliance test to make sure the appliance operates properly by plugging
the power supply cord into a 24
0 Volt grounded outlet.
Test all aspects of its operati
on (manual switches remote and heater) to make sure all
components are operating correctly.
As with most electronic devices your new electric fireplace has been designed to operate at
temperatures between 5 ℃ (41
℉
fireplace to reach room temperature before turning it on.
NOTE: There may be trace of odor during the first few minutes of initial use This is
harmless, normal and will never occur again
LOCATING THE FIREPLACE
Plan where
to locate and frame the fireplace. This will save time and money later when you
install the fireplace. Before installation consider the following:
1.
Where the fireplace is located must allow for wall and ceiling clearances
2.
Consider a location where the fire
windows or doors.
3. A 15 ampere 240 Volt 50-
60 Hz branch circuit with proper ground must be available at the
location. Preferably a dedicated branch circuit should be provided to avoid circuit breake
to trip of fuses to blow.
7
NG AND TESTING APPLIANCE
Carefully remove the appliance from the box.
Prior to installing the appliance test to make sure the appliance operates properly by plugging
0 Volt grounded outlet.
on (manual switches remote and heater) to make sure all
components are operating correctly.
As with most electronic devices your new electric fireplace has been designed to operate at
℉
) and 35 ℃ (95℉
). During the cold winter
fireplace to reach room temperature before turning
it on.
NOTE: There may be trace of odor during the first few minutes of initial use This is
harmless, normal and will never occur again
LOCATING THE FIREPLACE
to locate and frame the fireplace. This will save time and money later when you
install the fireplace. Before installation consider
the following:
Where the fireplace is located must allow for wall and ceiling clearances
Consider a location where the fire
place screen will not be exposed to direct sunlight from
60 Hz branch circuit with proper ground must be available at the
location. Preferably a dedicated branch circuit should be provided to avoid circuit breake
Prior to installing the appliance test to make sure the appliance operates properly by plugging
on (manual switches remote and heater) to make sur
e all
As with most electronic devices your new electric fireplace has been designed to operate at
). During the cold winter
months allow the
NOTE: There may be trace of odor during the first few minutes of initial use This is
to locate and frame the fireplace. This will save time and money later when you
Where the fireplace is located must allow for wall and ceiling clearances
place screen will not be exposed to direct sunlight
from
60 Hz branch circuit with proper ground must be ava
ilable at the
location. Preferably a dedicated branch circuit should be provided to avoid circuit breake
rs

8
SYM-34
Description Built-in Appliance
Voltage 220-240V AC 50-60Hz
Watts 1500W Max
NO HEATER 30W Max
MOTOR HEATER 19W
Appliance Width 32 3/8” or 82.3 cm
Appliance Height 15 5/8 ” or 39.6 cm
Appliance Depth 5 5/8” or 14.3 cm
Gross Weight 57.3 lbs or 26 kgs
Plug Location Left side
Cord Length 70 7/8” or 180 cm
Rough Wall Opening
Size
33 3/8”× 16“ or
84.8 cm× 40.6 cm
BTU 5118

SYM-42
Description Built-in Appliance
Voltage 220-240V AC 50-60Hz
Watts 1500W Max
NO HEATER 38W Max
MOTOR HEATER 19W
Appliance Width 42 1/4” or 107.2 cm
Appliance Height 15 5/8 ” or 39.6 cm
Appliance Depth 5 5/8” or 14.3 cm
Gross Weight 68.34 lbs or 31 kgs
Plug Location Left side
Cord Length 70 7/8” or 180 cm
Rough Wall Opening
Size
43 1/4”× 16“ or
109.8 cm× 40.6 cm
BTU 5118

10
SYM-50
Description Built-in Appliance
Voltage 220-240V AC 50-60Hz
Watts 1500W Max
NO HEATER 42W Max
MOTOR HEATER 19W
Appliance Width 50 1/4” or 127.6 cm
Appliance Height 15 5/8 ” or 39.6 cm
Appliance Depth 5 5/8” or 14.3 cm
Gross Weight 79.8 lbs or 36.2 kgs
Plug Location Left side
Cord Length 70 7/8” or 180 cm
Rough Wall Opening
Size
51 1/4”× 16“ or
130.2 cm× 40.6 cm
BTU 5118

11
SYM-60
Description Built-in Appliance
Voltage 220-240V AC 50-60Hz
Watts 1500W Max
NO HEATER 46W Max
MOTOR HEATER 19W
Appliance Width 60 1/4” or 153 cm
Appliance Height 15 5/8 ” or 39.6 cm
Appliance Depth 5 5/8” or 14.3 cm
Gross Weight 92.6 lbs or 42 kgs
Plug Location Left side
Cord Length 70 7/8” or 180 cm
Rough Wall Opening
Size
61 1/4”× 16“ or
155.5 cm× 40.6 cm
BTU 5118

12
SYM-74
Description Built-in Appliance
Voltage 220-240V AC 50-60Hz
Watts 1500W Max
NO HEATER 50W Max
MOTOR HEATER 19W
Appliance Width 74 1/4” or 188.5 cm
Appliance Height 15 5/8 ” or 39.6 cm
Appliance Depth 5 5/8” or 14.3 cm
Gross Weight 108 lbs or 49 kgs
Plug Location Left side
Cord Length 70 7/8” or 180 cm
Rough Wall Opening
Size
75 1/4”× 16“ or
191.2 cm× 40.6 cm
BTU 5118

13
SYM-88
Description Built-in Appliance
Voltage 220-240V AC 50-60Hz
Watts 1500W Max
NO HEATER 56W Max
MOTOR HEATER 19W
Appliance Width 88 1/4” or 224.1 cm
Appliance Height 15 5/8 ” or 39.6 cm
Appliance Depth 5 5/8” or 14.3 cm
Gross Weight 123 lbs or 56 kgs
Plug Location Left side
Cord Length 70 7/8” or 180 cm
Rough Wall Opening
Size
89 1/4”× 16“ or
226.6 cm× 40.6 cm
BTU 5118

14
SYM-100
Description Built-in Appliance
Voltage 220-240V AC 50-60Hz
Watts 1500W Max
NO HEATER 60W Max
MOTOR HEATER 19W
Appliance Width 100 1/4” or 254.6 cm
Appliance Height 15 5/8 ” or 39.6 cm
Appliance Depth 5 5/8” or 14.3 cm
Gross Weight 136.68 lbs or 62 kgs
Plug Location Left side
Cord Length 70 7/8” or 180 cm
Rough Wall Opening
Size
101 1/4”× 16“ or
257.1 cm× 40.6 cm
BTU 5118

INSTALLATION-
WALL MOUNT
NOTE:
Due to the many different materials used to build walls it is highly recommended that
you consult your local builder before you install this appliance on a wall.
1.
Select a location that is not prone to
moisture and is located at least 0.91 m
or 3 feet awa
y from combustible
materials such as curtains or drapes
furniture bedding paper etc.
2.
Using a spirit level to select a position
in which to mount the heater
horizontally. See Figure 1.
3. Check
the wall to ensure there is no
wiring pipe wires etc in the
drilled. Drill 8 or more holes depending
on the size of he unit purchased (8mm
diameter & 40mm depth) using a
suitable size drill bit and insert the wall
plugs into the holes.
4. R
emove the hanger from the fireplace
by removing the screws. See Fig
5. F
asten the hanger to the wall. See
Figure 3.
6. T
o prevent fireplace from moving use
the provided safety screw to fasten the
fireplace to the wall. See Figure 4.
WARNING: Be sure that the bolts have
been fixed firmly enough to withstand
the weight!
15
WALL MOUNT
Due to the many different materials used to build walls it is highly recommended that
you consult your local builder before you install t
his appliance on a wall.
Select a location that is not prone to
moisture and is located at least 0.91 m
y from combustible
materials such as curtains or drapes
furniture bedding paper etc.
Using a spirit level to select a position
in which to mount the heater
the wall to ensure there is no
wiring pipe wires etc in the
area to be
drilled. Drill 8 or more holes depending
on the size of he unit purchased (8mm
diameter & 40mm depth) using a
suitable size drill bit and insert the wall
emove the hanger from the fireplace
by removing the screws. See Fig
ure 2.
asten the hanger to the wall. See
o prevent fireplace from moving use
the provided safety screw to fasten the
fireplace to the wall. See Figure 4.
WARNING: Be sure that the bolts have
been fixed firmly enough to withstand
Due to the many different materials used to build walls it is highly recommended that
you consult your local builder before you install this appliance on a wall.

INSTALLATION- BUILT-
IN
NOTE: Due to the many different materials used to build walls it is highly recommended that
you consult your local builder before you install this appliance on a wall.
Preparation
1.
Select a location that is not prone to
from combustible materials such as curtains drapes furniture bedding paper etc.
2.
Mark the desired location on the floor and store the appliance in a safe dry and dust free
place.
3. Prepare a wall wit
h a framed opening to accommodate the size of your unit. Leave at
least 1/4” (6mm) around the edge of the appliance. Any new wiring must be done in
compliance with local and national codes and other applicable regulations.
Prior to installing test the app
liance to make sure the appliance is fully operational by
plugging the power supply cord into a
The rough wall opening size of the fireplace:
W(“)
SYM-34 33 3/8
SYM-42 43 1/4
SYM-50 51 1/4
SYM-60 61 1/4
SYM-74 75 1/4
SYM-88 89 1/4
SYM-100 101 1/4
INSTALLATION
1. Unscrew 4 screws
and take off the trim. (NOTE: Keep hold of the front glass as it may fall
down automatically when the trim is removed.)
16
IN
NOTE: Due to the many different materials used to build walls it is highly recommended that
you consult your local builder before you install t
his appliance on a wall.
Select a location that is not prone to
moisture and is located at least 0.91m or 3 feet away
from combustible materials such as curtains drapes furniture bedding paper etc.
Mark the desired location on the floor and store the appliance in a safe dry and dust free
h a framed opening to accommodate the size of your unit. Leave at
least 1/4” (6mm) around the edge of the appliance. Any new wiring must be done in
compliance with local and national codes and other applicable regulations.
liance to make sure the appliance is fully operational by
plugging the power supply cord into a
240 Volt grounded outlet.
The rough wall opening size of the fireplace:
D(“) H(“)
6 16
6 16
6 16
6 16
6 16
6 16
6 16
and take off the trim. (NOTE: Keep hold of the front glass as it may fall
down automatically when the trim is removed.)
NOTE: Due to the many different materials used to build walls it is highly recommended that
you consult your local builder before you install this appliance on a wall.
moisture and is located at least 0.91m or 3 feet aw
ay
from combustible materials such as curtains drapes furniture bedding paper etc.
Mark the desired location on the floor and store the appliance in a safe dry and dust free
h a framed opening to accommodate the size of your
unit. Leave at
least 1/4” (6mm) around the edge of the appliance. Any new wiring must be done in
compliance with local and national codes and other applicable regulations.
liance to make sure the appliance is fully operatio
nal by
and take off the trim. (NOTE: Keep hold of the fron
t glass as it may fall

2. When the trim is r
emoved take off the front glass panel.
3.
Unscrew the 2 screws located on each side and take off the inner side steel panels.
17
emoved take off the front glass panel.
Unscrew the 2 screws located on each side and take off the inner side steel panels.
Unscrew the 2 screws located on each side and take off the inner side steel panels.

4.
Put the trim back onto the appliance and fasten with screws.(NOTE: This step is to make
sure t
hat the fireplace fits the wall opening well and there is no gap between the trim and
the wall after installation)
5.
Put the fireplace into the wall opening and fix it to the wall by screwing 2 screws each
side.
18
Put the trim back onto the appliance and fasten with screws.(NOTE: This step is to make
hat the fireplace fits the wall opening well and there is no gap between the trim and
Put the fireplace into the wall opening and fix it to the wall by screwing 2 screws each
Put the trim back onto the appliance and fasten with screws.(NOTE: This step is to make
hat the fireplace fits the wall opening well and there is no gap between the trim and
Put the fireplace into the wall opening and fix it to the wall by screwing 2 screws each

6. Remove th
e trim following STEP 1. Screw back the inner side steel panels.
7.
Put back the front glass panel and screw back the trim after you finish the media
decoration.
1
e trim following STEP 1. Screw back the inner side steel panels.
Put back the front glass panel and screw back the trim after you finish the media
e trim following STEP 1. Screw back the inner side steel panels.
Put back the front glass panel and screw back the trim after you finish the media

INSTALLATION SEMI-
FLUSH BUILT
NOTE: Please purchase
special trim for the semi
dealer. See dealer for more details.
The rough wall opening size of the fireplace:
W(“)
SYM-34-B 33 3/8
SYM-42-B 43 1/4
SYM-50-B 51 1/4
SYM-60-B 61 1/4
SYM-74-B 75 1/4
SYM-88-B 89 1/4
SYM-100-B 101 1/4
1. Unscrew 4 screws
and take off the trim. (NOTE: Keep hold of the front glass as it may fall
down automatically when the trim is removed.)
20
FLUSH BUILT
-IN WITHIN 2 X 4’S
special trim for the semi
-flush built-
in installation from
dealer. See dealer for more details.
The rough wall opening size of the fireplace:
D(“) H(“)
4 16
4 16
4 16
4 16
4 16
4 16
4 16
and take off the trim. (NOTE: Keep hold of the front glass as it may fall
down automatically when the trim is removed.)
in installation from
and take off the trim. (NOTE: Keep hold of the fron
t glass as it may fall