Renaissance Glide-Aside 16GAAT1W User manual

USER MANUAL
*Please read Battery Warning & General Usage Advice on the last page of these instructions.
Remote Battery Insertion/Replacement*
Compatible with Glide-Aside® 2nd generation motors from January 2023
Glide-Aside®
Motorised Track
Tel [phone] •Email [e-mail] •Visit rca-uk.com
Dual Channel Remote
Model: 16GAAT1W
Back of
Remote
Back of
Remote
LCD 15-Channel Dual Remote
Model: 16GAAT15W
Use a tool (such as a sim card pin,
paper clip or mini screw driver)
to press the small release button and
push the battery cover down to open.
Battery Type: CR2450 3V
Working temperature: -10°C~50°C Transmitting Power: -10mW Radio Range: 200m Outdoors or 35m Indoor Use
Battery Life: 2 Years Approx. Radio Frequency: 433.05~434.79MHz
A
OPEN
STOP
CLOSE
B
OPEN
STOP
CLOSE
A
OPEN
STOP
CLOSE
Channel
Down
B
OPEN
STOP
CLOSE
Channel
Up
LCD
BLUE LED BLUE LED

USER MANUAL Glide-Aside® Motorised Track
2. Ensure that your Motor Battery is fully charged.
3. Connect the charged Battery to the Motor and locate the
motor reset button and indicator light (as shown below).
4. To clear and reset to default: Press and hold the reset button
down for around 10 secs until the green indicator light has
ashed 3 times – then release – the motor will beep 3 times.
The motor is now fully reset.
5. To pair a Remote: Read all the steps fully before you start
Press and hold the Reset Button down for around 3 secs until
the green Indicator Light has ashed once only – then release –
the motor will beep once also.
6. The motor is now ready to link to a new remote for the next 5
seconds only. Act quick – press and hold down the Stop Button
on the remote channel you want to link for around 3 secs.
7. The Motor will beep 3 times and the green Indicator Light will
also ash 3 times – now release your remote Stop Button.
8. Your remote is now paired and ready to use.
Pairing Remotes to Glide-Aside Battery Power Motor
NOTE: If you want
to add additional
Remotes or make the
other channel on a
Dual Remote active for
the same motor just
repeat steps 5 to 8.
1. Choose the le or right channel you want to pair on your Remote.
For LCD Multi-Channel Remotes you will also have to select a
channel No. from 1 to 15 too. Note Channel 0 is not an option!
Tel [phone] •Email [e-mail] •Visit rca-uk.com
INDICATOR
LIGHT
RESET
BUTTON
NOTE: Make sure you press
the le or right buttons on
the Dual Channel Remotes!
DO NOT press in-between!

2. Ensure that your wired motor is plugged into the mains.
3. Remove the cap at the base of the motor to reveal the motor
Reset Button and Indicator Light (as shown below).
4. To clear and reset to default: Press and hold the Reset
Button down for around 10 secs until the green Indicator Light
has ashed 4 times – it will then rapidly ash 5 times – then
release. The motor is now fully reset.
5. To pair a Remote: Read all the steps fully before you start
Press and hold the Reset Button down for around 3 secs until
the green indicator light has ashed once only – then release.
6. The motor is now ready to link to a new remote for the next 5
seconds only. Act quick – press and hold down the Stop Button
on the remote channel you want to link for around 3 secs.
7. The green Indicator Light will ash once – now release
your remote Stop Button.
8. Your remote is now paired and ready to use.
USER MANUAL Glide-Aside® Motorised Track
Pairing Remotes to Glide-Aside Mains Power Motor
NOTE: If you want
to add additional
Remotes or make the
other channel on a
Dual Remote active for
the same motor just
repeat steps 5 to 8.
Tel [phone] •Email [e-mail] •Visit rca-uk.com
INDICATOR
LIGHT
RESET
BUTTON
1. Choose the le or right channel you want to pair on your Remote.
For LCD Multi-Channel Remotes you will also have to select a
channel No. from 1 to 15 too. Note Channel 0 is not an option!
NOTE: Make sure you press
the le or right buttons on
the Dual Channel Remotes!
DO NOT press in-between!

USER MANUAL Glide-Aside® Motorised Track
Battery Warning & Remote General Usage Advice
REN073-2022-09-12/23
Tel [phone] •Email [e-mail] •Visit rca-uk.com
1. Do not expose your remote to moisture.
2. Do not drop or strike the remote as it may cause damage.
3. Ensure to use ONLY the battery type stated within these instructions.
4. If your remote is acting strangely or the range becomes shorter – please change battery.
5. If battery voltage is less than 2.6V a low voltage indicator will show (LCD version only) – please change battery.
6. Please ensure you dispose of used batteries at appropriate recycle facilities.