Reporter GX1122-DGR/H User manual

1
Erbas Teknoloji - Reporter GX1122-DGR/H User Manual
USER MANUAL
GX1122-DGR-rev1.05-1021
GX1122-DGR/H
GSM SMS ALARM & CONTROLLER
www.erbasteknoloji.com
ERBAŞ TEKNOLOJİ
Innovative Solutions

2
Erbas Teknoloji - Reporter GX1122-DGR/H User Manual
SAFETY INSTRUCTIONS
- This user manual contains important notices for installation, usage and safety instructions. Please
read this manual carefully before you start using your device!
- Device is containing a radio transceiver operating on GSM 850/900/1800/1900 MHz bands.
- Do not use device in environments, exceeding temperature limits (device should operate not lower
than -100 C and not higher than +500C).
- Do not use device in chemical or other hazardous environments.
- Device is intended to use in dry and clean places. Do not use device in high humidity.
- Protect your device from dust, moisture, heat and water.
- Do not expose the device to strong vibrations and mechanical impacts.
- Do not attempt to repair device personally.
USE IN ACCORDANCE WITH THE REGULATION
- The use of this device in accordance with the regulation is sending SMS text messages and making
phone calls after an alarm case and controlling remote devices via SMS and phone calls. Other usages
are not permitted.
- Police, fire or healthcare emergency call lines are not permitted to call directly from this device. Do
not configure emergency call numbers into this device.
LIMITED LIABILITY
- The buyer must agree that Reporter devices will reduce the risk of theft, burglary, fire or other
dangers and controls remote devices but do not guarantee any operation against such events.
- Manufacturer will not take any responsibility regarding personal or property or revenue loss while
using devices.
- Manufacturer liability according to local laws does not exceed value of the purchased device.

3
Erbas Teknoloji - Reporter GX1122-DGR/H User Manual
1. DESCRIPTION
Reporter GX1122 is a user friendly and a reliable device which sends you SMS text messages and calls
you in case of input alarm events, restorations and periodically sends heartbeat messages. It also
controls your remote devices via SMS, free phone call and DTMF phone calls.
It includes a lot of useful features like; detailed instant STATUS query, configurable SMS text
messages, configurable input delays, user defined heartbeat periods, alarm call enable/disable,
add/delete admins & users via SMS, relay activation method selection, LED indicators, replaceable
antenna, IP67 water & dust protected industrial enclosure.
GX1122 -DGR has:
-2 x Digital isolated inputs with +3…27 VDC wide range input voltage capacity
-2 x 10A 230VAC high-capacity relays with volt-free NO/NC/COM pins
-8 admin nr capacity
-20 user nr capacity for standard version / 1.000 user nr (H version only) for remote relay control
purposes
Below list shows the alert events from your device:
-Port1 High : Text Message and (optional) phone call ring
-Port1 Low : Text Message and (optional) phone call ring
-Port2 High : Text Message and (optional) phone call ring
-Port2 Low : Text Message and (optional) phone call ring
-Device Activated : Detailed Text Message *
-Keep Alive : Detailed Text Message *
-Status : Detailed Text Message *
* Detailed text message includes: All inputs status, all outputs status, Call mode selection, Alarm
call configuration, Keep alive period and CSQ GSM signal level in dBi.
Note that Reporter devices do not have “voice record” function, so phone calls are used for only ringing
your mobile phone. There is no voice call.
Only a local 850/900/1800/1900 MHz GSM SIM card is required to operate the device. SMS and Call
function is enough for SIM Card. Data or GPRS functions are not required.
All settings and registered admin & user numbers are saved in Reporter’s own memory. So, settings will
not be deleted if power is failed or SIM card is removed/replaced. Device will continue with the last saved
settings & numbers.

4
Erbas Teknoloji - Reporter GX1122-DGR/H User Manual
2. USECASES
2.1. Remote Controlling
This device can be used to control electrically operated devices remotely via SMS Commands or Phone
Calls. With the help of high capacity & operation configurable relays, you may Activate, Deactivate,
Trigger or Time-Based Activate your remote devices. All Admins and Users can use these control
functions.
Use cases might be such as:
-Irrigation systems
-Trigger Gate openers / barriers
-Control Lighting
-Control total electricity of your home/office/plant etc.
-Different kinds of motors and machines and much more…
As soon as integrated relay power is suitable (up to 10A / 240VAC), any kind of
device/machine/system could be controlled with this device. In some cases where required switching
power is higher than the device capacity; then it can still control those devices by some additional
high capacity switching equipment (i.e. contactors).
2.2. Input Monitoring
Any kind of volt-free or +3V…+27VDC voltage ranged sensor/switch/device output could be
connected to Reporter isolated inputs. Thus, Reporter will continuously check for any change on the
inputs, and it will inform all Admins by SMS (optionally Free Phone Call) in case of changes on the
inputs.
Use cases might be such as:
-Burglar alarm systems as a dialer
-Fire alarm systems as a dialer
-Door/window monitoring
-Any sensors like gas/smoke/earthquake monitoring
-Water level monitoring
-Flood monitoring
-Panic alarm monitoring
-Specific electronic devices/system monitoring and much more…

5
Erbas Teknoloji - Reporter GX1122-DGR/H User Manual
3. INSTALLATION
Package includes:
-4 x screws for “Cover Fitting”
-4 x screws for “Wall Mount”
-4 x fixing plugs for “Wall Mount”
-1 x waterproofing fitting
Firstly, unscrew the Cover Fitting screws and then open the top cover.
If you want to mount your device to the wall;
-Place device to the wall
-Point Wall Mount screwing holes (shown below) to the wall
-Drill the wall from pointed places
-Insert fixing plugs into the drilled points
-Screw in the wall mount screws from the screwing points of the device

6
Erbas Teknoloji - Reporter GX1122-DGR/H User Manual
4. GETTING STARTED
4.1. Insert SIM Card
A local SIM card is required to operate the system.
Required SIM card size is NanoSIM (as seen in figure).
SMS and Call (if you require) services should be active on the SIM.
However, Data/Internet/GPRS services are not required.
Before inserting the SIM card, try it with a mobile phone. And then:
oDisable PIN code protection
oSend an SMS to a mobile number for testing
oCall a mobile phone number for testing
After above steps completed, open the screws. And insert SIM card into the device, by pushing it as
shown in below figure.

7
Erbas Teknoloji - Reporter GX1122-DGR/H User Manual
4.2. Connect Inputs and Outputs on Ports
Note: Wires should pass into the holes of the bottom cover! Please check Wiring Diagram!
If you want to apply external powered lines to the inputs; make sure voltage levels are between +3V
and +27V. It is also very important that you need to connect external device’s GND line to Reporter
GND terminal.
If your external equipment is volt-free (i.e. a button, switch, magnetic contact or volt-free relay
output); in this case you may use Reporter’s +12V line to supply your external equipment.
Reporter inputs are digital and isolated.
4.3. Connect Power
Note: Wires should pass into the holes of the bottom cover! Please check Wiring Diagram!
Connect 12V DC power supply into terminal block +12V (positive) and GND (negative/ground).
Two pieces of +12V and two pieces of GND pins are internally
parallel.
Please note external power should be rated at +12VDC and
current should be at least 1000 mA (1A).
5. DEVICE CONFIGURATION
Firstly, make sure “POWER LED” (Red one) is ON. This indicates that external power is ON.
Then check for “NETWORK STATUS LED”.
-Off : Powered off
-Fast Blink : Not ready (registering to network)

8
Erbas Teknoloji - Reporter GX1122-DGR/H User Manual
-Slow Blink : Ready (registered to the network)
Once NETWORK STATUS LED starts blinking slowly; then you are ready to go to next steps.
Note: Device Configuration and Reset is only made by SMS commands. There is no other method.
Below is the table of SMS commands available:
DESCRIPTION
COMMAND
DEFAULT
RANGE
AUTHORISATION
Change Password
PASS:xxxx
1111
0000..9999
ADMIN
Add Admin
ADDA:xxxxxxxxxx
ADMIN
Add User
ADDU:xxxxxxxxxx
ADMIN
Delete Admin
DELA:xxxxxxxxxx
ADMIN
Delete User
DELU:xxxxxxxxxx
ADMIN
Alert Calls Activate
CALL:ON
OFF
ADMIN
Alert Calls Deactivate
CALL:OFF
OFF
ADMIN
Select MOD1 and Trigger Time(x)
MOD1:x
MOD1:2
1..99 secs
ADMIN
Select MOD2
MOD2
MOD1:2
ADMIN
Change SMS Text Messages
PATx:yyyyyyyy#
1..32 chars
ADMIN
Set Input nr(x) Low-to-High Delay
INPHx:y
0
0..99 secs
ADMIN
Set Input nr(x) High-to-Low Delay
INPLx:y
0
0..99 secs
ADMIN
Set Keep Alive (Heartbeat) SMS
Period
KA:x
0 (means
disabled)
0...999
hours
ADMIN
Get Device Status Info
STATUS
ADMIN
Restore Factory Settings
RESET
ADMIN
Activate Relay nr(x)
RLYx:ON
ADMIN & USER
Deactivate Relay nr(x)
RLYx:OFF
ADMIN & USER
Time-based Activate Relay nr(x) for
(y) secs
RLYx:y
0..99 secs
ADMIN & USER
SMS message format is:
Password<space>Command1<space>Command2<space>Command3……
Examples:
1111 ADDA:[phone] // Adds an Admin
1111 PASS:4567 CALL:ON // Changes password to 4567 & activates calls
4567 ADDU:[phone] ADDU:[phone] // Adds two users by using last password
4567 RLY3:5 // Turns ON RLY3 for 5 secs and then turns OFF
4567 RLYALL:OFF // Turns OFF all relays
5.1. Register (Add) Admin Number(s)
Before adding an Administrator (Admin) please be aware of Admins and Users have different
authorizations. Please decide which numbers to add as Admin and which to add User by the help of below
information.
Admin numbers are authorized to make configurations, change & delete settings and reset device, add
& remove users & admins, receive all alert notifications and control device outputs (relays) remotely.
User numbers can only control Relay Outputs via phone call or by sending SMS to the device.

9
Erbas Teknoloji - Reporter GX1122-DGR/H User Manual
Note-1: If there is no Admin registered yet, any number who knows default password may add itself as
Admin.
Note-2: After first Admin is registered to the device; only an existing Admin may add another Admin.
Note-3: Total 8 people can be added as Admin.
Authorization : Admins only (or first number on first use)
Format : Password<space>ADDA:Number
Example : 1111 ADDA:[phone]
Responses : Process Succeed. // format & password is correct
Process Failed! // format is wrong
Record Succeed. Memory Full // record done but now memory is full
Record Failed! Memory Full // cannot record because memory is full
5.2. Change Password
Authorization : Admins only
Format : Password<space>PASS:NewPassword
Example : 1111 PASS:6666
Responses : Process Succeed. // format & password is correct
Process Failed! // format is wrong
Note: New Password must be always different than “1111”.
5.3. Register (Add) User(s)
Note: Total 20 (1.000 for /H models) people can be added as User.
Authorization : Admins only
Format : Password<space>ADDU:Number
Example : 1111 ADDU:[phone]
Responses : Process Succeed. // format & password is correct
Process Failed! // format is wrong
Record Succeed. Memory Full // record done but now memory is full
Record Failed! Memory Full // cannot record because memory is full
5.4. Delete Admin
Authorization : Admins only
Format : Password<space>DELA:Number
Example : 1111 DELA:[phone]
Responses : Process Succeed. // format & pass is correct. Nr exists
Process Failed! // format is wrong
Record Not Found! Process Failed // nr does not exist

10
Erbas Teknoloji - Reporter GX1122-DGR/H User Manual
5.5. Delete User
Authorization : Admins only
Format : Password<space>DELU:Number
Example : 1111 DELU:[phone]
Responses : Process Succeed. // format & pass is correct. Nr exists
Process Failed! // format is wrong
Record Not Found! Process Failed // nr does not exist
5.6. Alert Calls Activate / Deactivate
Alert Call feature is used if you need a Phone Call to warn you after you receive alert SMS.
These Calls do not include a voice record. It’s a free-call to ring your phone for around 45 seconds.
Alert Calls are DISABLED (OFF) as factory default.
Authorization : Admins only
Format : Password<space>CALL:ON
Password<space>CALL:OFF
Examples : 1111 CALL:ON // enables phone calls
1111 CALL:OFF // disables phone calls
Responses : Process Succeed. // format & pass is correct
Process Failed! // format is wrong
5.7. MOD1/MOD2 Selection (Relay Control by Phone Calls)
To control Relay Outputs by Phone Calls; Reporter has two different mode options.
Only one of them has to be selected. As factory default, MOD1 is selected:
-MOD1 is only used to trigger RLY1 in a predefined period (default: 2 seconds). When you call device;
it will reject the call after a few rings. Then it will Turn ON RLY1 for predefined period and it will
Turn OFF RLY1 after this period. If this mode is selected MOD2 will be disabled.
-MOD2 is used to Turn ON & Turn OFF all available Relays individually via DTMF Call Dial Service.
When you call device; it will pick up and wait you dial Relay Nr and dial “ #/* ” for ON/OFF. If this
mode is selected MOD1 will be disabled.
Authorization : Admins only
Format : Password<space>MOD1:Period
Password<space>MOD2
Examples : 1111 MOD1:6 // select MOD1, set trig. time to 6 secs
1111 MOD2 // select MOD2
Responses : Process Succeed. // format & pass is correct
Process Failed! // format is wrong