Repotec RP-WR5441L User manual

Wireless 11N 150Mbps AP Router
Quick Installation Guide
V1.0

Wireless 11N 150Mbps Broadband Router Quick Installation Guide
1
1. Check your package contents
The following items should be found in your package:
¾Wireless 11N 150Mbps Broadband Router
¾Power adapter
¾CD-Rom
Please make sure that the package contains the above items, if any of the listed items is
damaged or missing, please contact with your distributor.
2. Before you begin
You must have the following at least:
¾Broadband Internet Access Service(DSL/Cable/Ethernet)
¾10/100Base-T Ethernet card and TCP/IP protocol installed for each PC
¾Internet Explorer 5.0 or higher for Web configuration
¾802.11n , 802.11g or 802.11b compliant wireless adapters (for wireless connection)

Wireless 11N 150Mbps Broadband Router Quick Installation Guide
2
3. Hardware Installation
Figure 3-1
¾Attach one end of the Ethernet cable with RJ-45 connector to your computer’s Ethernet
port, and the other end to one of the LAN ports of your router.
¾Connect the Ethernet cable attaching to your Cable/ADSL modem to the WAN port of
your router.
¾Connect the single DC output connector of the power adapter to the power jack on the side
of the router. Then plug the Power Adapter into an AC outlet.
4. LED indicators
LED Function
SYS Flashing
Power on
CPU on
WLAN ACT
WPS working (orange)
WAN On WAN Connection normal

Wireless 11N 150Mbps Broadband Router Quick Installation Guide
3
Flashing Data transmitting
On LAN Connection normal
LAN Flashing Data transmitting
Flashing slowly WPS is running
WPS OFF WPS is not running
5. Login
¾Open a web browser (Safari, Internet Explorer, etc.) on the computer you have just
connected to the router, type http://192.168.1.1 in the address bar, and press enter
Figure 5-1
¾In the pop-up window, enter the user name guest and password guest and then click OK
Figure 5-2
¾Login successfully and the home page appears, the left navigation bar shows the main
options to configure the system, the right screen is the summary information for viewing the

Wireless 11N 150Mbps Broadband Router Quick Installation Guide
4
configurations.
6. System Setup
6.1.Internet connection setting
¾Most connections utilize a dynamic IP (DHCP) and the default is already set to this. If you
have another connection type (like static IP), you will need to click on ‘Convenient Setup’ in
the menu and input information given you by your service provider and then click save.
Figure 6-1
¾You may already be connected to the Internet. Click on ‘System Information’- ‘Internet
access info’ to see if you have an IP, Gateway, etc (refer to the following picture). If not, your
service provider probably requires you clone the MAC address of your computer to the router.
To do so, click on ‘Internet Setup’ in the menu, then click on ‘Clone MAC Address’ button to
get your computer's MAC address in according to your Internet connection type, and then click
the ‘Save’ button below.

Wireless 11N 150Mbps Broadband Router Quick Installation Guide
5
Figure 6-2
¾If you are still not connected, your modem may actually have the same IP as the router
(192.168.1.1). You will need to change the router's IP. Click on ‘LAN Setup’- ‘LAN IP
Address’ and you will see this IP in the main interface. You may edit it to something different
(192.168.2.1 for example). After entering the new IP, click on ‘Save’ below, the router will
reboot, and you will need to enter the user name and password again. Check your system status
for IP again, and test connection.
Note: You will need to enter the new IP in the browser to access the user interface for any
future setting changes.
Figure 6-3
Now you can enjoy your new network. If you have anything related to the questions below,
please refer to the following part
6.2.Advanced setting
6.2.1. Restore to factory setting
If the router ever freezes in a setting change process or if you can’t access it because you can’t

Wireless 11N 150Mbps Broadband Router Quick Installation Guide
6
remember the IP you have given it or other problem, you may have to utilize the default button
on the back of the router to put it back to factory settings. You have to press this button for
about 1, 2 seconds with a pencil when it is working, then leave your hands, it will restore
settings to the factory configuration
6.2.2. Password modify
You may wish to change the router's password. To do so, click on ‘System Management’-
‘Password setup’, enter a new password and then confirm it.
6.2.3. Firmware upgrade
‘Upgrade’ will give you the option to upgrade the router's firmware if you download a newer
version in the future.
6.2.4. Wireless security setting
To protect your wireless network from unauthorized user access, you need to encrypt your
router. Click ‘Wireless management’- ‘Security’, it supplies “None”, “WEP”, “WPA-PSK”,
“WPA2-PSK” and “WPA/WPA2-PSK” five different encryption modes. But WEP
authentication mode is not recommended when WPS enabled.
If you want to use WEP to encrypt, you can select ASCII characters (alphanumeric format) or
Hexadecimal digits (‘A-F’, ‘a-f’ and ‘0-9’). 64-bit WEP: input 10 Hex values (in the ‘A-F’,
‘a-f’ and ‘0-9’ range) or 5 ASCII characters. 128-bit WEP: input 26 Hex values (in the ‘A-F’,
‘a-f’and ‘0-9’ range) or 13 ASCII characters
Figure 6-4
If you want to use WPA/ WPA2/ WPA&WPA2 to encrypt, you can select ASCII characters

Wireless 11N 150Mbps Broadband Router Quick Installation Guide
7
(alphanumeric format) or Hexadecimal digits (‘A-F’, ‘a-f’ and ‘0-9’). No matter what type
you select, input 64 Hex values (in the ‘A-F’, ‘a-f’ and ‘0-9’range) or 8-63 ASCII characters.
Figure 6-5
You can also use WPS to encrypt your network. WPS can connect the wireless adapter and the
router in a safe way. If you have a wireless network card which has WPS button, you may set up
a safe network via the following methods
Figure 6-6
Note: the WPS PIN is on the bottom of the router
Method 1:
¾Push the WPS hardware button of the Router until the orange WPS LED flashes
¾Push the WPS button in the wireless network card for about 3-5 seconds
¾The safe connection will be established automatically, please wait
Method 2:
¾Check ‘Input PIN from AP’ in the wireless adapter’s WI-FI protect setup page, input PIN
of the router, then click ‘PIN Input Config (PIN)’

Wireless 11N 150Mbps Broadband Router Quick Installation Guide
8
Figure 6-7
¾Select this router in the pop-up window, then click ‘Select’
¾The connection will be established automatically.