Resolution Products RE927S-03-00 User manual

RE927S_3G GSM Communicator Page 1 of 6 16-May-14
24-Hour Tech Support Line: [phone]
www.ResolutionProducts.com
Wireless
Security
Solutions
RE927S-03-00 3G GSM Communicator with Z-wave
Features
• Connects panels to GSM Network
• Compatible with:
o GE Simon XT
o GE Simon XT
• Enables:
o larm Reporting
o Interactive Control Functions
o Ethernet data reliability
o Z-Wave Communicator included
Key Instructions
• The same unit works for GE Simon XT & GE Simon XTi.
• The RE927S mounts inside the GE Simon XT panel and communicates with
the GE Simon XT and GE Simon XTi via the Expansion Connector.
• The antenna should be mounted in a location that will optimize cellular
signal strength. Mount as high in the building as possible. Mount the
ntenna as far as possible from large metal objects and sources of
interference.
Operation
Event Reporting:
Events are reported to both the CMS monitoring receiver and the Securenet
interactive server. The following events are reported by default:
larms
larm cancels
Openings
Closings
System Low Battery
System Low Battery Restoral
C Power Fail
C Power Restoral
Interactive Control:
The system may be controlled remotely through the Securenet interactive
platform.
Z-Wave
Z-Wave devices can be controlled via the Interactive function.
Siren (RE116-C)
Can be used with a Simon XT
Future: Simon XTi
Revert to Factory Default Button
Press and hold for 5 seconds: Resets the board and keeps all settings
Press and hold for 10 seconds: Reverts board back to the factory default settings
RE927S_3G GSM Communicator Page 2 of 6 16-May-14
24-Hour Tech Support Line: [phone]
www.ResolutionProducts.com
Picture
LEDs
Ethernet LEDs
Indication
Power
(Green)
ON and flashing once per second when the board is pow
ered and
running
GSM
(Red)
ON when the unit is registered with the local GSM network
CS
(Red)
ON when the connection to the CMS central station is established
Platform
( mber)
On when the connection to the Panel, and connection to the
SiteControl interactive server is established
Z
-
Wave
Module
Revert to
Factory
Default Button
GSM
ntenna
Connector
Z
-
Wave
ntenna
GSM
Card
Status LEDs

RE927S_3G GSM Communicator Page 3 of 6 16-May-14
24-Hour Tech Support Line: [phone]
www.ResolutionProducts.com
Programming:
1) Refer to server setup instructions and set up the account on the Site
Control Dealer Portal.
2) Disarm the System.
3) Power down the GE Simon XT system.
4) Plug RE927S into the back of the GE Simon XT control panel. (Picture
below) board communicates via the Expansion Connector.
5) String the GSM antenna to mount in a location for best GSM signal.
6) pply power to the GE Simon XT system.
7) The keypad should display “Resolution GSM Module”.
8) Installation is complete.
GSM Communicator
in the
Expansion Connector
RE927S_3G GSM Communicator Page 4 of 6 16-May-14
24-Hour Tech Support Line: [phone]
www.ResolutionProducts.com
Specifications
Current Draw: 230 m Nominal
Temperature Range: 0F to 120F
Housing dimensions: 2x4x1/2 inches
Specifications subject to change without notice.
GE Simon X Firmware Version Compatibility
1.3 (minimum)
Notices
“GE , “Honeywell , “DSC , “2GIG and “Napco are trademarks owned by General Electric
Company, Honeywell International Inc., Tyco Safety Products Canada LTD, 2GIG Technologies Inc.,
and NAPCO Security Systems, Inc., respectively.
Resolution Products, Inc. products will function with one of either GE, Honeywell, DSC or Napco
systems. However, no Resolution product is produced by, endorsed by, nor is officially associated
with GE, Honeywell, DSC or Napco. Resolution recommends verifying proper enrollment and
operation, per control panel installation instructions, at installation.
Warranty
Resolution Products, Inc. will replace products that are defective in their first five (5) years.

RE927S_3G GSM Communicator Page 5 of 6 16-May-14
24-Hour Tech Support Line: [phone]
www.ResolutionProducts.com
FCC Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions:
(1)This device may not cause harmful interference.
(2)This device must accept any interference that may be received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the Resolution Engineering, Inc. could
void the user's authority to operate this equipment.
CC ID: U5X-RE927
This device contains CC ID: QISMU509C
RF Exposure:
To satisfy FCC RF Exposure requirements for mobile and base station transmission devices,
a separation distance of 20 cm or more should be maintained between the antenna of this
device and persons during operation. To ensure compliance, operation at closer than this
distance is not recommended.
The antenna(s) used for this transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
RE927S_3G GSM Communicator Page 6 of 6 16-May-14
24-Hour Tech Support Line: [phone]
www.ResolutionProducts.com
IC Notice
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1)This device may not cause interference, and
(2)This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1)l'appareil ne doit pas produire de brouillage, et
(2)l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
Model: RE927S
IC: 8310A-RE927
This device contains IC: 6369A-MU509C
Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry
Canada. To reduce potential radio interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not
more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour
l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son
gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas
l'intensité nécessaire à l'établissement d'une communication satisfaisante.