Resolution Products RE219 User manual

RE219_Honeywell_Flood_Temp_Instructions.docPage 1 of 9/6/2011
www.ResolutionProducts.com
Wireless
Security
Solutions
RE219 House Disaster: Flood/Temp Range,
Honey ell-Compatible
Features
•Tri-Mode Environmental Sensing:
oFlood/Moisture Sensor
oFreeze – for Furnace Failure
oOverheat – for Furnace runaway or Air Conditioning failure.
•3 unique wireless Loops: one for each function
•Cover tamper.
•Strong, reliable RF signal.
•8-10 year battery life on CR123A battery.
•Low Battery indication.
•3.3x1. x1.1 inches.
Key Instructions
•Battery “+” faces towards spring.
•Enrolling:
Place Panel in Zone Programming mode.
Zone Type = for example, 2 -Hr. Aux.
Input Type = Supervised RF Transmitter.
When asked for serial number, press Tamper switch.
Program the desired Loop number you want that zone to
monitor. Loop functions are:
•Loop 1: Overheat.
•Loop 2: Flood.
•Loop 3: Freeze.
•Loop : Tamper.
•Test Temp alarm functions by putting in a freezer, or blowing a hair dryer on
sensor.
•Test Flood alarm function by putting sensor in water (distilled water will not
work, but tap water should).
RE219_Honeywell_Flood_Temp_Instructions.docPage 2 of 9/6/2011
www.ResolutionProducts.com
Operation
•Flood – Loop 2:
Alarm: when liquid rises 0.0 0 inches above sensor bottom.
Tamper: when cover is opened.
Supervisory: every hour.
•Freeze – Loop 3
Alarm: when room temperature drops below 0F.
Tamper: when cover is opened.
Supervisory: every hour.
•Overheat – Loop 1
Alarm: when room temperature rises above 100F.
Tamper: when cover is opened.
Supervisory: every hour.

RE219_Honeywell_Flood_Temp_Instructions.docPage 3 of 9/6/2011
www.ResolutionProducts.com
Specifications
Flood sensing: Titanium contacts
100K-Ohm nominal (DO NOT use an EOL resistor)
0.0 inch floor spacing to eliminate floor
condensation falses.
Checks moisture every 30 seconds
(test mode: every second when cover is off)
Freeze Alarm: 0F +/- 2F (custom temps available)
Restores when temp increases F from alarm
Overheat Alarm Temp: 100F +/- 2F (custom temps available)
Restores when temp decreases F from alarm
Mounting hardware: #6 or #8 screws
Dual Mode mounting:
Screwed to floor
Screwed to wall
Terminal wire capacity: 16 Gauge
Replacement Battery: CR123A 1550 mAH
Temperature Range: 0F to 120F
Housing dimensions: 3.3x1. x1.1 inches
Specifications subject to change without notice.
Internal & Close-up Pictures
Temp Element
Strain relief for
floor mounting
RE219_Honeywell_Flood_Temp_Instructions.docPage of 9/6/2011
www.ResolutionProducts.com
Notices
“GE”, “Honeywell”, and “DSC” are trademarks owned by General Electric Company, Honeywell
International Inc., and Tyco Safety Products Canada LTD, respectively.
Resolution Products, Inc. products will function with one of either GE, DSC or Honeywell systems.
However, no Resolution product is produced by, endorsed by, nor is officially associated with GE,
Honeywell or DSC. Resolution recommends verifying proper enrollment and operation, per control
panel installation instructions, at installation.
Warranty
Resolution Products, Inc. will replace products that are defective in their first year.
FCC Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:
This device may not cause harmful interference.
This device must accept any interference that may be received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the Resolution Products, Inc. could void
the user's authority to operate this equipment.
FCC ID: U5X-RE201X
IC Notice
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
Cet appareil est conforme avec d’Industrie Canada RSS standard exempts de licence. Son
fonctionnement est soumis aux deux conditions suivantes:
1. Ce dispositif ne peut causer des interférences, et
2. Ce dispositif doit accepter toute interférence, y compris les interférences qui
peuvent causer un mauvais fonctionnement du dispositif.
IC: 8310A-RE201