Response Electronics miGuard A9 User manual

Quick Start Guide
A9
lines open 0900 to 1700 Monday to Friday
“ whatever your question, we’re just a phone call away “
0345 257 1000
miGuard Customer Helpline
Wireless Burglar Alarm
Remote Monitoring/Communicating
PSTN Keypad Control

Congratulations on your purchase of the
A9 Remote Monitoring/Communicating
Burglar Alarm System
I. Installing the Control Panel
Important: Use only the telephone cables supplied with the
System.
a. Read the instructions thoroughly
b. Remove all the contents from their
packaging
c. Consider the most appropriate positioning
of the Control Panel and each Accessory
The Accessories supplied with the System are
already pre-programmed to the Control
Panel
for ease of installation. Any additional
Accessories will need to be programmed to
the Control Panel, as shown in the Full
Instruction Manual.
IMPORTANT NOTES TO BE READ
PRIOR TO SETTING UP YOUR SYSTEM
1 x Control Panel
1 x Pet Friendly PIR Motion
Sensor
1 x Door/Window Sensor
2 x Remote Controls
Kit Contents
1 x AC/DC Adapter
2 x Telephone Cables
All Batteries & Fixings
Instruction Manual
Power LED Indicator
Setup/Wireless Signal LED Indicator
Arm LED Indicator
Panic Button
Zone LED Indicators
Escape
Arm
Disarm
Home Arm (Part Arm)
Carefully remove the battery cover at the back
of the unit using a flat-bladed screwdriver.
Power on (AC Adapter):
1. Plug the Power Jack into the Control Panel
2. Plug the Power Supply into a suitable Power Socket
3. Turn the Power Switch from ‘OFF’ to ‘ON’
(see following illustration)
For installation where a telephone is in general use,
first unplug the existing telephone from the phone
wall socket, then:
1. Using the telephone cable provided, connect the
RJ11 connector into the socket labelled ‘LINE’ in
the Control Panel, then plug the BT connector
(at the other end of the lead) into the phone
wall socket.
2. Using the second telephone adapter cable, connect
the RJ11 connector into the socket marked
‘PHONE’ in the Control Panel, then plug your
existing telephone into the other end of the
adapter cable.
For installation where an existing telephone is NOT in
general use/required, follow step 1 only as above (the
3. Refit the battery cover, ensuring the power supply
and telephone cables sit within the channel, exiting
from the top of the Battery Compartment.
Follow steps II to IV overleaf to install/set-up the
pre-programmed Accessories.
Connecting the Telephone Cables:
LINE PHONE
3
2
1

II. Installing a Door/Window Sensor
Please refer to the System’s full instruction
manual for detailed programming.
1. Press the Arm Button on the Remote Control
2. The Control Panel will emit one beep to
indicate that it is armed.
3. If your Control Panel is set to delay it will
beep every two seconds for half of the
duration of the delay, it will intensify in
tempo for the remaining duration to warn
that System Arming is imminent.
IV. Remote Control Operation
1. Remove the activation strip from the battery
compartment.
2. Remove the backing paper from one side of each
double-sided adhesive strips. Fix one adhesive
strip to the back of the Magnet and one to the
back of the Transmitter (alternatively for
permanent fixing use the screws supplied).
3. Peel off the other side of each adhesive strip.
Mount the Magnet on the door and the
Transmitter on the door frame (small triangles
facing each other), with less than a 6mm
separation between the two.
4. When opening the door a small red indicator
lights up briefly, this indicates that the
Transmitter has sent a signal to the Control
Panel.
LED
LED
1. Remove the activation strip. Fit the retaining screw
supplied.
2. Self-testing will commence for 1 minute, indicated
by the LED flashing every two seconds. Press the
Test Button, the LED will then flash once when
movement is detected, for up to 3 minutes.
3. Fit the Sensor in a position that will cover your
desired protection area:
a. Fix the bracket to the wall with the fixings kit
supplied. For optimum performance set the
the height of the bracket to 2 metres above
ground level.
b. Adjust angle of the PIR sensor to cover the
required detection area (see diagrams **).
4. To test, walk in front of the Sensor - the LED should
illuminate once when movement is detected. If the
Sensor is triggered twice in 3 minutes, it will enter
into power saving (sleep mode). If no movement is
detected within the next 3minutes, the Sensor will
return to normal working mode.
III. Installing a PIR Motion Sensor
Top view Side
2m
Ground

miGuard is a trademark of Response Electronics Limited © copyright 2014. All rights reserved
www.responseelectronics.com
Response Electronics Limited
Roman House, Lysons Avenue, Ash Vale, Surrey, GU12 5QF
email: [email protected]
The product is guaranteed for one year from the date of purchase against faulty materials and
workmanship. No liability can be accepted for any problems caused by fair wear and tear,
buyer’s negligence, improper fitting or use, wilful or accidental damage, or any consequential
loss or damage howsoever caused. This guarantee does not affect your statutory rights and is
valid for UK and EIRE only.
If you believe the product to be faulty or in the unlikely event of the product developing a fault
during the warranty period, then please contact our Technical Support Team (contact details
shown below) for product assistance. Product repair or replacement will be offered for faulty
products only with our prior agreement. Should you need to return a product then:
1. Contact the Helpline on the number below to obtain a Return Authorisation Number
2. Return your product adequately packaged, ideally in its original packaging to prevent damage
in transit, and include the following:
a. A copy of your original invoice/receipt
b. A covering letter giving your full contact details, including email address (if applicable)
c. A description of the fault or problem
GUARANTEE
Disposal and Recycling
Disposal of this product is covered by the Waste Electrical or Electronic Equipment (WEEE)
Directive. It should not be disposed of with other household or commercial waste.
At the end of its useful life the packaging and product should be disposed of via a suitable
recycling centre. Please contact your local authority or the retailer from where the
product was purchased for information on available facilities.
A9_Q_V2_1433
0345 257 1000
miGuard Customer Helpline