Retracta AR320 User manual
AR320
ARC320
AR415
ARC415
AR420
ARC420
AW315
AW320
AW415
AW420
CL315
CL320
CLC320
INCLUDES MODEL NOs:
PREMIUM HOSE REELS
OWNERS MANUAL
AIR / WATER / COOLANT Hose Reels
IMR3AIR - issue 1
PAGE 2
INSTRUCTION MANUAL
• Do not exceed the maximum working
pressure for this reel. (Refer to the
product specifications).
• Only use compatible fluids with this
reel. (Refer to compatible fluids in
product specifications).
• Check equipment daily for wear or
damage. (Replace worn or damaged
items immediately with genuine
replacement parts).
• Use equipment for intended use only.
• Check equipment daily for leaks.
(Repair or replace as required).
• Do not alter or modify equipment.
• Do not let go of the hose when
rewinding.
• Use reel in well ventilated areas if toxic
or flammable fluids are in use.
• Do not attempt to stop leaks with your
hand or body.
INTRODUCTION
Thank you for purchasing the Retracta R3 retractable hose reel.
PLEASE READ THIS SAFETY INFORMATION CAREFULLY BEFORE USE.
Read and retain this instruction manual to assist you in the operation of your new
product.
‘CAUTIONS’ are listed throughout this manual to advise of actions that may cause
damage to you’re the operator or to the equipment.
CAUTION
The following general warnings should be observed when installing, operating or
maintaining hose reel equipment. Further specific warnings pertaining to specific
dangers may be found within this document
Note,
This is not an exhaustive list of hazards and warnings. All care should be taken to maintain safe
working procedures when installing, operating and maintaining the equipment. It is recommended
that only trained professional trades people with the appropriate working knowledge of such
equipment be charged with its installation and maintenance.
Before attempting any
maintenance, disconnect and
turn o the supply line, then
release the line pressure
PAGE 3
INSTRUCTION MANUAL
INSTALLATION INSTRUCTIONS
INCREASE SPRING TENSION
1. Use appropriate hardwear to secure and
support the reel and bracket to desired location
and weight of the fluids.
2. Prevent the reel from swiveling in the overhead
position (figure 2) by installing the locking
bracket supplied.
3. Use the 8mm screw provided to secure the pin
to the BU200 bracket. A padlock (not supplied)
can be fitted for additional security.
4. If spring recoil tension requires adjusting refer
to “Add spring tension” for correct proceedure
5. Connect the fluid supply line to the side of the
reel making sure to tighten appropriately.
6. It is recommended that an isolation valve is
installed before the reel inlet.
7. Connect a desired hose-end attachment and
tighten appropriately. Thread sealant may be
required.
8. Purge the air from the reel and check for any
leaks or damage before initial use.
9. Before carrying out any maintenance, close
isolation valve and remove all line pressure.
Fig.1
Wall mounting
(max height 1.4m)
Fig.3
BB100 Bracket
Floor/Bench
Fig.2
Overhead mounting
(max height 4.5m)
Fig.4
BB100 Bracket
High wall mounting
(max height 4.5m)
1. Remove screws 2. Add 2 complete turns
Note:
1 click on hub equals 90 deg
3. Replace screws
CAUTION
Before attempting any
maintenance, disconnect and
turn o the supply line, then
release the line pressure
PAGE 4
INSTRUCTION MANUAL
HOSE REPLACEMENT
1. Pull out hose and
latch
5. Remove cable tie
9. Attach hose to the
swivel
13. Fit screws
3. Remove screws
7. Remove old hose
11. Fit cable tie
15. Recoil hose evenly
into reel
2. Remove screws
6. Remove swivel
10. Fit swivel assembly
14. Fit screws
4. Remove plate
8. Fit new hose
12. Fit sideplate
CAUTION
Before attempting any
maintenance, disconnect and
turn o the supply line, then
release the line pressure
PAGE 5
INSTRUCTION MANUAL
SWIVEL or SWIVEL SEAL
REPLACEMENT
1. Pull out hose and
latch
5. Remove cable tie
8. Attach hose to the
swivel
12. Fit screws
3. Remove screws
7. Remove body from shaft. Replace o-rings.
Apply water resistant grease
10. Fit cable tie
14. Recoil hose evenly
into reel
2. Remove screws
6. Remove circlip
9. Fit swivel assembly
13. Fit screws
4. Remove plate
11. Fit sideplate
Swivel
replacement
Instructions
use steps
1-5 & 9-15
CAUTION
Before attempting any
maintenance, disconnect and
turn o the supply line, then
release the line pressure
PAGE 6
INSTRUCTION MANUAL
REMOVE / REPLACE
TENSION SIDE PLATE
CAUTION
Before attempting any
maintenance, disconnect and
turn o the supply line, then
release the line pressure
1. Remove screws with
madnetic screwdriver
5. Remove screws
9. Fit screws
3. Release spring
tension
7. Fit new side plate 8. Fit screws
11. Add 2 complete
turns
2. Hold hub and remove
screws
6. Remove side plate
10. Fit screw
4. Remove screw and
center hub
11. Fit screws
PAGE 7
INSTRUCTION MANUAL
TROUBLESHOOTING GUIDE
CAUTION
Before attempting any
maintenance, disconnect and
turn o the supply line, then
release the line pressure
Hose does not retract
correctly
A) Outlet nozzle, gun or
tool is too heavy
B) Spring is fatigued and
lost tension
Refer to INCREASE SPRING
TENSION on page 3.
Reel does not latch
A) Incorrect operation
B) Latch assembly is broken
Refer to REMOVE / REPLACE
TENSION SIDE PLATE
on page 6.
Leaking from hose
Split in hose Refer to HOSE REPLACEMENT
on page 4.
Leaking from swivel
Swivel or swivel seals
are worn
Refer to SWIVEL OR SWIVEL
SEAL REPLACEMENT on page
5.
PAGE 8
INSTRUCTION MANUAL
SWIVEL ASSEMBLIES
SPARE PARTS LIST
REFER TO : Page 5
SWIVEL OR SWIVEL SEAL REPLACEMENT INSTRUCTIONS
Air / Air Water
O’Ring seal kit
BS115VS
Swivel Assembly kit
1/2”(12.5mm) - RS115As
3/8”(10mm) - RS116As
O’Ring seal kit
BS115VS
Swivel Assembly kit
1/2”(12.5mm) - RS117As
Coolant
Item No. Description Spart Part No.
1 Tension hub set R3THs
2 Latch set R3Ls
3 Latching side plate R3LPs
4 Inlet side plate R3IPs
5 Drum assembly R3DAs
6 Mouth set R3Ms
7 Standard Bracket (incl locking plate) R3SBs
8 Outer Casing - single (nom color) R3OCS-color
9 Lower insert (nom colour) R3LIS-color
Swivel Assemblies
10 RS115A (1/2”) Air/Water R115As
10 RS116A (3/8”) Air/Water R116As
10 RS117A - Coolant R117As
Swivel Seal Kits
12 Swivel seal set Air/Water/CR/WP (not shown) BS115Vs
Description Spart
Part No.
HOSE STOPPERS
RP156-1 (3/8” air/water) Stopper RP156-1s
RP156-2 (1/2” air/water) Stopper RP156-2s
HOSE ASSEMBLIES
3/8”x 20m air RH35s
1/2”x 15m air RH22s
1/2”x 20m air RH150s
3/8”x 15m air/water RH151s
3/8”x 20m air/water RH152s
1/2”x 15m air/water RH153s
1/2”x 20m air/water RH154s
NOZZLE SET
Coolant gun (Coolant reel only) R3CG
WALL BRACKET
Wall Bracket (not shown) BU200
PAGE 9
INSTRUCTION MANUAL
EXPLODED DIAGRAM
Note:
1. Outer casing is supplied as a single half only.
2. Standard bracket not shown.
Hose reel master assembly
(Refer to spare parts list on previous page)
15
8
9
34
10
6
8
2
PAGE 10
INSTRUCTION MANUAL
PAGE 11
INSTRUCTION MANUAL
Note:
This product should be disposed of according
to all applicable local and national government
environment regulations and guidelines.
For Warranty Terms and Conditions see macnaught.com.au
For a list of Australian Service Centres see macnaught.com.au
Macnaught Pty Limited
ABN 66 000 075 785
41 - 49 Henderson St
Turrella, NSW, 2205
Sydney, Australia.
Postal Address PO Box 90
Arnclie NSW 2205 Sydney,
Australia.
T. +61 2 9567 0401
F. +61 2 9597 7773
W. www.macnaught.com.au
This manual suits for next models
12
Table of contents
