RGBlink Driver 2A User manual

Driver 2A–Quick Start
Installation and cabling features
Rear Panel
Connections
Step 1-Mounting
Turn off or disconnect all equipment power sources.
Driver 2A Quick Start
Rev 1.0
Page 1 of 2
Address: S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone, Xiamen, Fujian Province, P.R.C
Tel: [phone] Fax:[phone]
Email: [email protected] http://www.rgblink.cn
Step 4-HDMI Input
VIEW SIZE THE WORLD
NOTE
This guide provides quick start instructions for an experienced installer
to set up and operate the Driver 2A.
For full installation, configuration, and operation details, please refer to
the Driver 2A user manual, which is available at www.rgblink.com.
Step 3-DVI Input
Use to input DVI from DVI player or
computer with DVI connector.
Nixie Tube
Step 5-Gigabit Copper Port
Can receive video signal from HD player,
DVD and computer.
Local Control Front Panel Operation
Can control the brightness of LED sending card, and
the nixie tube will display the brightness value.
Connect to LED screen through cable. LED Indicator
Red: Power indicator, it lights when device has power
supply.
Green: Signal indicator, it lights when device has
signal input.
USB Control Port of Sending Card
User can connect PC via USB cable and
control sending card software.
Function Button
Function Button
Button 2: Down key, can switch to the top level
brightness value.
Button 3: Up key, can switch to the next level
brightness value.
How to connect
Connect the HD player, DVD or computer to the
HDMI input interface with HDMI cable.
Connect the DVI player or computer with DVI
interface to the DVI interface with DVI cable.
Connect the computer to the USB control port of
sending card with USB cable.
Connect the receiving card of LED Display to the
Gigabit Copper Port with cable.
1
2DVI Input Interface
Audio Input Interface
Switch
4
8
7Gigabit Copper Port
3HDMI Input Interface Power
6
5
9
Step 2-Audio Input
Connect to microphone or the device with audio
interface.
Step 6-Power
Plug in power cord which has IEC connector, Driver 2A
supports AC power from 85 to 264V, 50-60Hz, which
means world wide compatible.
Power On
Connect one end of the power with the device, the other
end into a socket, and push power switch to ON
position. Red power indicator light means the device
works normally.
1USB control Port of
Sending Card
Nixie Tube
6
2Function Button LED Indicator
3
Operation Manual
45

Driver 2A Quick Start
Rev 1.0
Page 2 of 2
Address: S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone, Xiamen, Fujian Province, P.R.C
Tel: [phone] Fax:[phone]
Email: [email protected] http://www.rgblink.cn
Nixie tube can not display brightness value
It usually occurs in Nova sending card. When Nova
sending card connected to PC software via USB, the key
operation of control brightness is invalid, and nixie tube
will not display the brightness value. User can only
control the brightness via PC software or pull out the
USB cable to recover the key brightness controlling.
How to control the brightness of sending
card
1. First, make sure the device is in normal operation.
2. Choose the brightness value according to actual need
via UP/DOWN keys, the adjustment value range is
0~16 for Colorlight Q7e sending card, 0~64 for
Nova MSD300 sending card, and 1~16 for Linsn 801,
802 and DBstar HRV2011 sending card. The higher
the brightness value, the brighter sending card will be.
Common Questions and Solution
No output on LED display
1. Check whether input the signal.
2. Check whether the cable is connected, and in good
connection.
3. Check whether the input and output cable are normal.
Connect the microphone or other devices with audio
interface to the audio interface with 3.5mm headphone
cable.
Plug in power cord with IEC connector.
How to work
Push power button to ON position, the red indicator is
on if the device is in normal operation.
When input DVI and HDMI signal simultaneously, the
HDMI signal has priority, green signal indicator lights,
and the device output HDMI signal. Pull out the HDMI
cable, green signal indicator lights, and then the device
output DVI signal.