RGBlink Q2 Series User manual

1
Q2 Series
User Manual
Article NO: RGB-RD-UM-Q2 E002
Version NO: V1.2

Q2 User Manual
2
Content
Content...................................................................................................................................................2
Declarations............................................................................................................................................3
FCC/Warranty.................................................................................................................................. 3
Operators Safety Summary............................................................................................................. 4
Installation Safety Summary............................................................................................................4
Chapter 1 Your Product.......................................................................................................................... 6
1.1 In the Box...................................................................................................................................6
1.2 Product Overview......................................................................................................................7
1.2.1 Key Features.................................................................................................................... 7
1.2.2 Front Panel...................................................................................................................... 8
1.2.3 Rear Panel......................................................................................................................10
1.2.4 Dimension......................................................................................................................13
Chapter 2 Install Your Product..............................................................................................................16
2.1 Plug in Power...........................................................................................................................16
2.2 Connect Input Signal Source................................................................................................... 16
2.3 Connect Output Source........................................................................................................... 17
Chapter 3 Use Your Product................................................................................................................. 19
3.1 XPOSE 2.0 Installation............................................................................................................. 19
3.2 XPOSE Operation..................................................................................................................... 22
3.2.1 Login in XPOSE...............................................................................................................22
3.2.2 System Setting............................................................................................................... 24
3.2.3 Output|Input|Overview................................................................................................28
3.2.4 Display Management.....................................................................................................34
3.2.5 Layer Management........................................................................................................36
3.2.6 Preset Management......................................................................................................43
3.3 XPOSE APP Control.................................................................................................................. 45
Chapter 4 Order Code.......................................................................................................................... 46
4.1 Product Code...........................................................................................................................46
4.2 Module Code........................................................................................................................... 46
Chapter 5 Support................................................................................................................................ 47
5.1 Contact us................................................................................................................................47
Chapter 6 Appendix..............................................................................................................................48
6.1 Specification............................................................................................................................ 48
6.2 Terms & Definitions................................................................................................................. 51
6.3 Revision History....................................................................................................................... 57

Q2 User Manual
3
Thank you for choosing our product!
This User Manual is designed to show you how to use this video processor quickly and make use of all the
features. Please read all directions and instructions carefully before using this product.
Declarations
FCC/Warranty
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area may cause harmful
interference, in which case the user will be responsible for correcting any interference.
Guarantee and Compensation
RGBlink provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of
guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred
during transport, as well as for material and manufacturing faults. RGBlink must be informed immediately in
writing of any complains.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the
date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of compliant,
RGBlink can repair the fault or provide a replacement at its own discretion within an appropriate period. If this
measure proves to be impossible or unsuccessful, the purchaser can demand a reduction in the purchase price or
cancellation of the contract. All other claims, in particular those relating to compensation for direct or indirect
damage, and also damage attributed to the operation of software as well as to other service provided by RGBlink,
being a component of the system or independent service, will be deemed invalid provided the damage is not
proven to be attributed to the absence of properties guaranteed in writing or due to the intent or gross negligence
or part of RGBlink.
If the purchaser or a third party carries out modifications or repairs on goods delivered by RGBlink, or if the goods
are handled incorrectly, in particular if the systems are commissioned operated incorrectly or if, after the transfer
of risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser
will be rendered invalid. Not included in the guarantee coverage are system failures which are attributed to
programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal
maintenance are not subject to the guarantee provided by RGBlink either.
The environmental conditions as well as the servicing and maintenance regulations specified in this manual must
be complied with by the customer.

Q2 User Manual
4
Operators Safety Summary
The general safety information in this summary is for operating personnel.
Do Not Remove Covers or Panels
There are no user-serviceable parts within the unit. Removal of the top cover will expose dangerous voltages. To
avoid personal injury, do not remove the top cover. Do not operate the unit without the cover installed.
Power Source
This product is intended to operate from a power source that will not apply more than 230 volts rms between the
supply conductors or between both supply conductor and ground. A protective ground connection by way of
grounding conductor in the power cord is essential for safe operation.
Grounding the Product
This product is grounded through the grounding conductor of the power cord. To avoid electrical shock, plug the
power cord into a properly wired receptacle before connecting to the product input or output terminals. A
protective-ground connection by way of the grounding conductor in the power cord is essential for safe operation.
Use the Proper Power Cord
Use only the power cord and connector specified for your product. Use only a power cord that is in good condition.
Refer cord and connector changes to qualified service personnel.
Use the Proper Fuse
To avoid fire hazard, use only the fuse having identical type, voltage rating, and current rating characteristics. Refer
fuse replacement to qualified service personnel.
Do Not Operate in Explosive Atmospheres
To avoid explosion, do not operate this product in an explosive atmosphere.
Installation Safety Summary
Safety Precautions
For all product installation procedures, please observe the following important safety and handling rules to avoid
damage to yourself and the equipment.
To protect users from electric shock, ensure that the chassis connects to earth via the ground wire provided in the
AC power Cord.
The AC Socket-outlet should be installed near the equipment and be easily accessible.

Q2 User Manual
5
Unpacking and Inspection
Before opening product shipping box, inspect it for damage. If you find any damage, notify the shipping carrier
immediately for all claims adjustments. As you open the box, compare its contents against the packing slip. If you
find any shortages, contact your sales representative.
Once you have removed all the components from their packaging and checked that all the listed components are
present, visually inspect the system to ensure there was no damage during shipping. If there is damage, notify the
shipping carrier immediately for all claims adjustments.
Site Preparation
The environment in which you install your product should be clean, properly lit, free from static, and have
adequate power, ventilation, and space for all components.

Q2 User Manual
6
Chapter 1 Your Product
1.1 In the Box
AC Power Cord
DVI Cable
HDMI-DVI Cable
Network Cable
Anti-Static Bag
Note: AC Power Cable supplied as standard according to destination market.

Q2 User Manual
7
1.2 Product Overview
Q2 adopts modular design, supporting 8 layers on each output module.Each layer supports for scaling,
moving, crossing and overlying. Besides,It supports custom output resolutions. It also supports RGBlink XPOSE 2.0
software operation.
Q2 SYSTEM CONNECTION DIAGRAM
1.2.1 Key Features
●Each module supports up to 8 layers
●Each layer support for scaling, moving, crossing and overlying
●Support 4K@60 inputs and outputs
●Each module supports for customized output resolution,single port's width up to 3840 and height up to 3840
●Optional independent audio input&output modules
●XPOSE visualization operation
●EDID management

Q2 User Manual
8
1.2.2 Front Panel
1
2
Q2-2
Q2-4

Q2 User Manual
9
1/2/3
Power Switch
3
Q2-8

Q2 User Manual
10
1.2.3 Rear Panel
4
1
2
3
Q2-2
Note：purple tip indicates input, blue tip indicates output, yellow tip indicates communication.
1
Purple Input 1-3
Input slots 1-3,supporting DVI,HDMI, DP modules and other
optional modules.
2
Blue Output 1-2
Output slots 1-2,supporting HDMI and other optional modules.
3
Yellow COMM
Communication board with LAN and RS232 port ，to connect
router or computer to realize software control.
4
Power

Q2 User Manual
11
1
2
3
4
Q2-4
1
Purple Input 1-9
Input slots 1-9,supporting DVI,HDMI,DP,H.264 modules and
other optional modules.
2
Blue Output 1-5
Output slots 1-5,supporting HDMI,DVI and other optional
modules.
3
Yellow COMM
Communication board with LAN and RS232 port,to connect
router or computer to realize software control.
4
Power Interface,4U and above supports double power.

Q2 User Manual
12
1
Purple Input 1-18
Input slots 1-18,supporting DVI,HDMI, DP,H.264 modules
and other optional modules.
2
Blue Output 1-10
Output slots 1-10, supporting HDMI,DVI and other
optional modules.
3
Yellow COMM
Communication board with LAN and RS232 port ，to
connect router or computer to realize software control.
4
Power Interface，4U and above supports double power.
4
2
Q2-8
3
1

Q2 User Manual
13
1.2.4 Dimension
Following is the dimension of Q2-2 for your reference:
446mm×370mm×89mm
Q2-2

Q2 User Manual
14
Following is the dimension of Q2-4 for your reference:
484mm×373mm×178mm
Q2-4

Q2 User Manual
15
Following is the dimension of Q2-8 for your reference:
488mm×370mm×355.6mm
Q2-8

Q2 User Manual
16
Chapter 2 Install Your Product
2.1 Plug in Power
2.2 Connect Input Signal Source
Connect power and Q2-4 with standard AC Power Cord.
Take Q2-4 as example
Q2 series supports HDMI、DVI、SDI、DP1.2、HDBaseT and other optional input modules.
Connect Q2-4 with IP Camera,PC,DVD,laptop and other device as shown in the figure above.

Q2 User Manual
17
2.3 Connect Output Source
2.4 Connect control Computer
Method 1：Direct Connection:Connect Q2-4 with computer via network cable as shown in the figure below.It is
suitable for single user to control the device.
Method 2：Router Connection:Connect control computer and Q2-4 with Router as shown in the figure below.It
supports simultaneous online operation by multiple users.
Q2 Series supports SDI、DVI、HDMI、HDBaseT and other optional output modules.
Connect Q2-4 with monitors.
Q2 series is operated by XPOSE,so it is necessary to connect device with control computer.

Q2 User Manual
18
2.5 Connect PVW Module
Q2 series supports preview input source via control computer or output image via monitor.
2.6 Turn on Your Q2
LAN:preview input and output
HDMI monitor:preview input source
After connection,slightly press the power button in the front panel to turn on Q2.

Q2 User Manual
19
Chapter 3 Use Your Product
3.1 XPOSE 2.0 Installation
Environment Requirements:
Window
Processor: 1 GHz or above 32 bit or 64 bit processor
Memory: 4 GB or more
Graphics: Support Direct X9 128M or above (open AERO effect)
Hard disk space: Above 16G (primary partitions, NTFS format)
Monitor：Resolution must be 1920×1080 pixel or above(it can not display normally if the resolution is lower than
1920×1080)
Operating system: Windows 7 or above (full version, not Ghost version or compact version)
CPU:i5 and above
Mac
Monitor:Resolution must be 1680×1050 pixel or above(it can not display normally if the resolution is lower than
1680×1050)
CPU:i5 and above
1. Double click ,it will pop-up the installer
language box, select the language, for example,
select “English”, and click “OK” to confirm.
Note ：The following XPOSE operation takes Q2-4 as an example, and other U models operate the same
except for the difference of interface.

Q2 User Manual
20
2. Click “Next” to install
3. Click “Browse...” to select the XPOSE software
install location
Click “Install”
4. During installation, it will pop up the window of
Install Shield Wizard for Virtual Com port