RH Baby&child LANDRY PANEL CRIB User manual

LANDRY PANEL CRIB INSTRUCTIONS
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing to the address above. Include
the product model number, color, and a brief description of the part. Call 1-800-762-1751.
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Dust often using a clean, soft, dry cloth.
Blot spills immediately and wipe with a clean damp cloth. If the crib is to be stored, store in a cool dry place and carefully package all original
hardware to protect from loss.
TOOLS AND INSTALLATION
Tools Necessary: Allen Key (included)
NOTE: It may be easier to assemble product with two people.
NOTE: When inserting bolts, turn clockwise until tight. Then loosen 12- 34of a turn. After crib is completely assembled, return to each bolt and
tighten. Use wax or soap on all bolts to facilitate assembly
WARNING: Read all
instructions before assembling this
product. KEEP INSTRUCTIONS
FOR FUTURE USE.
Page 1
All Restoration Hardware cribs are designed to meet the highest safety
standards and comply with all U.S. and Canadian cribs and cradles regulations.
Made in Vietnam
Distributed in the U.S.A. by:
Restoration Hardware Baby & Child
2900 North Macarthur Dr. Tracy,
CA95376, USA
www.rhbabyandchild.com
Distributed in Canada by:
Restoration Hardware Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia V6E4N7

Page 2
IMPORTANT SAFETY INFORMATION FOR CRIBS
WARNING: Infants can suffocate on soft bedding. Never add a pillow or
comforter. Never place additional padding under an infant.
WARNING: Failure to follow these warnings and the assembly instructions
could result in serious injury or death.
·To reduce the risk of SIDS, pediatricians recommend healthy infants to be placed on their backs to
sleep, unless otherwise approved by your physician.
Strangulation Hazard:
·Strings can cause strangulation! DO NOT place items with a string around a child’s neck, such as
hood strings or pacifier cords. DO NOT suspend strings over over a crib or attach strings to toys.
·To help prevent strangulation tighten all fasteners. A child can trap parts of the body or clothing on
loose fasteners.
·DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Fall Hazard:
·When a child is able to pull to a standing position, set mattress to lowest position and remove
bumper pads, large toys and other objects that could serve as steps for climbing out.
·When child is able to climb out or reaches the height of 35 in (89 cm), the crib shall no longer be
used, and the child should be placed in a youth or regular bed.
·Check this product for damaged hardware, loose joints, missing parts or sharp edges before and
after assembly and frequently during use. Securely tighten loose bolts and other fasteners. DO NOT
use crib if any parts are missing, damaged or broken. Contact customer service at 1-800-762-1751
for replacement parts and instructional literature if needed.
·DO NOT substitute parts.
·DO NOT use a water mattress with this crib.
·If refinishing, use a non-toxic finish specified for children’s products.
·Follow warnings on all products in a crib.
·Never use plastic shopping bags or other plastic film as mattress covers because they can cause
suffocation.
·Infants can suffocate in gaps between crib sides and a mattress that is too small.

Page 3
IMPORTANT SAFETY INFORMATION FOR CRIBS
CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT
LEAST 27-1/4 INCHES BY 51-5/8 INCHES WITH A
THICKNESS NOT EXCEEDING 6 INCHES.
WARNING
Do not use this crib if you cannot exactly follow the instructions
that come with it.
Do not use this crib for a child who can climb out of it or who is
taller than 90 cm.
Do not place any cord, strap or similar item in or near this crib
that could become wrapped around a child's neck.
Do not place this crib near a window or patio door where a child
could reach the cord of a blind or curtain and be strangled.
Check this crib regularly before using it, and do not use it if any
part is loose or missing or if there are any signs of damage. Do
not substitute parts. Contact the manufacturer if replacement
parts or additions instructions are needed.
Children can suffocate on soft bedding. Do not place pillows,
comforters or soft mattresses in this crib.
Use a mattress that is no thicker than 15 cm and is of such a size
that, when it is pushed firmly against any side of this crib, it does
not leave a gap of more than 3 cm between the mattress and any
part of any other side of the crib.

Page 4
IMPORTANT SAFETY INFORMATION FOR TODDLER & DAY BEDS
·The mattress intended for use on the bed shall be a full-size crib
mattress having minimum dimensions of 51-5/8 inches (1310mm) in
length, 27-1/4 inches (690mm) in width and 4 inches (100 mm) in
thickness, not exceeding 6 inches (152 mm) in thickness.
·If guardrails are used as the mattress containment means,
guardrail(s) provided must be used to avoid the formation of a gap
between the mattress and the bed that could cause an entrapment.
·DO NOT place bed near windows where cords from blinds or drapes
may strangle a child.
·DO NOT place items with a string, cord, or ribbon around a child’s
neck, such as hood strings or pacifier cords.
·DO NOT suspend strings over a toddler bed for any pacifier cords.
·A child using the toddler or day bed shall be at least 15 months of age
and shall not weigh more than 50lbs (22.7kgs).
WARNING: ENTRAPMENT / STRANGULATION HAZARD
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
NEVER use bed with children under 15 months.
NEVER place bed near windows where cords from blinds or drapes
may strangle a child.

Page 5
ITEM IDENTIFICATION
For ease of identification, all parts are labeled to correspond to the step number in which
the part is used.
Step #1 End panels and botttom frame assembly (Page 6)
Step #2 Mattress support assembly (Page 7)
Step #3 Side rails assembly (Page 8)
Step #4 Hide unused holes (Page 9)
Step #5 Toddler rail assembly (Page 10)
SIDE RAIL
END PANEL
END PANEL
MATTRESS SUPPORT
BOTTOM FRAME

Page 6
STEP #1
END PANEL & BOTTOM FRAME ASSEMBLY
STEP#1.1:
Attach the end panel to the bottom frame by using Allen
bolts (AA) with the lock washers and plain washers. See
DETAIL A.
STEP#1.2:
Repeat above procedure to attach the other end panel to
the bottom frame.
HARDWARE NEEDED FOR STEP #1:
(AA) 1/4" x 1-3/4" BOLT = 6 pcs
Lock Washers 1/4" = 6 pcs
Plain Washers 1/4" = 6 pcs
Allen Wrench = 1 pc
DETAIL A

Page 7
STEP #2
MATTRESS SUPPORT ASSEMBLY
STEP #2.1:
Attach the support arms to the mattress support, using Allen bolts
(BB) with lock washers and plain washers. See DETAIL B.
STEP #2.2:
Hang the mattress support on both end panels by using Allen bolts
(BB), lock washers and plain washers, as per illustration in DETAIL C.
WARNING:
Set the mattress support to the desired height by adjusting the
support arms. The mattress support should be at its highest setting
for newborns, then adjusted to the lower positions as the child grows
and becomes mobile. Once the child is able to stand, the mattress
support should be at its lowest position.
HARDWARE NEEDED FOR STEP #2:
(BB) 1/4" x 13/16 " BOLT = 8 pcs
Lock Washer = 8 pcs
Plain Washer = 8 pcs
Allen Wrench = 1 pc
Support Arm = 4 pcs
B
Support Arm
(BB)
DETAIL B
C
(BB)
DETAIL C

Page 8
STEP #3
SIDE RAILS ASSEMBLY
On both ends of the side rail are holes for the bolt to pass
through, which correspond to the holes on the posts for both
end panels with pre-installed nuts. Attach the side rail to the
end panels by using Allen bolts (AA) with lock washers and
plain washers. See DETAIL D.
After assembly, re-tighten all bolts for a snug fit. DO NOT
OVER TIGHTEN.
HARDWARE NEEDED FOR STEP #3:
(AA) 1/4" x 1-3/4" BOLT = 8 pcs
Lock Washers 1/4" = 8 pcs
Plain Washers 1/4" = 8 pcs
Allen Wrench = 1 pc
(CC)
DETAIL D

Page 9
STEP #4
HIDE UNUSED HOLES
When the mattress support is in middle or lowest setting, unused holes can hurt your child's fingers. Use Allen bolts (CC) provided to hide these holes.
See illustration in DETAIL E.
HARDWARE NEEDED FOR STEP #4:
Allen Wrench = 1 pc
(CC) 1/4" x 1/2" BOLT = 8 pcs
DETAIL E
(CC)

Page 10
STEP #5
TODDLER RAIL ASSEMBLY
STEP #5.1:
Loose all the bolts in both ends of the front side
rail to disassemble the front side rail.
STEP #5.2:
Replace the front side rail by the toddler rail. See
DETAIL F.
After assembly re-tighten all bolts to snug fit. DO
NOT OVER TIGHTEN.
STEP #5.3:
Some unused holes which can be visible can hurt
your child's finger. Please use Allen bolts (EE)
provided (Packed inside Toddler rail box) to hide
these holes. See illustration in DETAIL G.
Allen Wrench = 1 pc
(EE) 1/4" x 1/2" BOLT = 2 pcs
HARDWARE FOR STEP #5:
(PACKED INSIDE TODDLER RAIL BOX)
G
F
(EE)
DETAIL G
(CC)
DETAIL F