RH Baby&child CALLUM 355-123 User manual

WARNING: Read all
Instructions before assembling
this product.
KEEP INSTRUCTIONS FOR
FUTURE USE.
Page 1 of 10
CUSTOMER SERVICE
If you are missing partsor have any questions about this product, contact us first. You can also order parts by writing to
the address above. Include the product model number, color, and a brief descriptionof the part.Call 1-800-762-1751.
CARE AND CLEANING
TOOLS AND INSTALLATION
Tools Necessary: Key Wrench (included).
NOTE : It may be easier to assemble productwith two people.
NOTE: When inserting bolts, turn clockwise until tight. Then loosen 1/2-3/4 of aturn. After crib is completely assembled,
return to each bolt and tighten.
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning.If the crib is to be stored, store in a cool
dry place and carefully package all original hardware to protect from loss.
CALLUM FULL LOFT BED – ASSEMBLY INSTRUCTIONS
Made in Vietnam
Model No: 355 - 123
Distributed in the U.S.A by:
RH Baby&Child
2900 N MACARTHUR DRIVE
TRACY, CA 95376
www.rhbabyandchild.com
Distributed in Canada by:
RH Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia
V6E4N7

Page 2 of 10
IMPORTANT SAFETY INFORMATION FOR BUNK BED
-
1. Follow the information on the WARNINGS appearing on the upper bunk end structure and on the
carton. DO NOT REMOVE WARNING LABEL FROM BED.
2. Always use the specified size mattress or mattress support, or both to help prevent the likelihood of
entrapment or falls.
3. Surface of mattress must be at least 5 inches below the upper edge of guardrails on top bunk.
4. Do not allow children under 6 years of age to use the upper bunk. Maximum load rating 400lbs.
5. Prohibit more than one person on upper bunk.
6. Periodically check and ensure that the guardrails, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact Restoration Hardware for replacement parts
10. Use of a night light may provide added safety precaution for a child using the upper bunk.
11. Use guardrails on both sides of the upper bunk.
12. If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed
should be placed against the wall to prevent entrapment between the bed and the wall.
13. The use of water flotation mattresses is prohibited.
14. STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are
not designed for use with the bed: for example, but not limited to, hooks, belts, and jump ropes.
15. Keep these instructions for future reference.
CALLUM FULL LOFT BED – ASSEMBLY INSTRUCTIONS
TO HELP PREVENT SERIOUS OR FATAL INJURIES FROM
ENTRAPMENT OR FALLS
1. Never allow a child under 6 years on upper bunk.
2. - If bunk is Twin/Twin:
Use only mattress which is 75" long and 38" wide and 7" height on upper bunk,
and mattress which is 75" long and 38" wide and 10" height on lower bunk.
- If bunk is Full/Full:
Use only mattress which is 75" long and 53" wide and 7" height on upper bunk,
and mattress which is 75" long and 53" wide and 10" height on lower bunk.
3. Ensure thickness of mattress does not exceed 7"and mattress surface is at least
5 inches below upper edge of guardrails. Thickness for lower bunk is 10” high.
4. Use guardrails on both sides of upper bunk.
5. Prohibit horseplay on or under bed(s).
6. Prohibit more than one person on upper bunk.
7. Use ladder for entering and leaving upper bunk.
8. If the bunk bed will be placed next to a wall the guardrails that run the full length
of the bed should be placed against the wall to prevent entrapment between
the bed and the wall.
STRANGULATION HAZARD
9. Never attach or hang items to any part of the bunk bed that are not designed for
use with the bed, for example, but not limited to hooks, belts, and jump ropes.
DO NOT REMOVE THIS LABEL
WARNING

PARTS IDENTIFICATION
Page 3 of 10
(A) Bunk Bed End (x2 pieces)
(G) Stretcher Bars (x4 pieces) (H) Platform Panels (x2 pieces)
(B) Ladder (x1 piece)
(F) Boottom Side Rail (x1 piece)
CALLUM FULL LOFT BED – ASSEMBLY INSTRUCTIONS
(D) Long Side Guard Rail (x1 piece)
(E) Short Side Guard Rail (x1 piece)
(C) Front/Back Guard Rails (x2 pieces)

Page 4 of 10
HARDWARE INCLUDED
TOOLS NEEDED
Phillips-head screwdriver (not included)
ASSEMBLY INSTRUCTIONS
Note: - Bed must be assembled by at least two people.
- Please read instructions carefully before assembling bed.
- Use the parts and fittings list to identify each component.
- Keep all packing materials until assembly is complete to avoid loss of smaller parts.
- Do not completely tighten all bolts until all steps are finished.
1
2
3
4
5
6
7
8
48 pieces
68 pieces.
12 pieces.
12 pieces.
12 pieces.
1 piece
Short Screw 8x19mm
6 pieces.
4 pieces.
Small Metal Bracket 51x38x1.5mm
Long Metal Bracket 200x52x4mm
Long Screw 8x30mm
NO. ITEM DESCRIPTIONQTY.
Threaded Rod 5/16” x 2-1/2”
Hex Nut 5/16” x 12mm
Hex Wrench 12 mm
Curved Slotted Washer 5/16”
CALLUM FULL LOFT BED – ASSEMBLY INSTRUCTIONS

Page 5 of 10
CALLUM FULL LOFT BED – ASSEMBLY INSTRUCTIONS
BUNK BED END ASSEMBLY INSTRUCTIONS
STEP 1:
STEP 2:
NOTE: Each side rail needs 2 people to assembly, put the bunk bed end panel on a straight line, insert the side rail on end
panel at the same time and set up hardware to assembly but not fully tighten, set up another side rail & hardware,
then tighten them.
1
c
2
3
5
F
C
C
Secure the Threaded Rod (1) into the Bunk Bed End (A).
1
Raise the Front/Back Guard Rails (C) and Bottom Side Rail (F)
up and place the rod into the Bunk Bed Ends (A) at the bore
holes’ position.
Insert Curved Slotted Washer (2), Hex Nuts (3) and tighten
with Wrench (5).
CORRECT
INCORRECT

STEP 3:
Page 6 of 10
CALLUM FULL LOFT BED – ASSEMBLY INSTRUCTIONS
Determine which side you wish to position the ladder.
Attach Long Metal Brackets (8) to the Short Side Guard
Rail (E) and Long Side Guard Rail (D) using 8x19mm
Short Screws (6) that are provided.
The bunk has total of 4 orientations. Short Side Guard Rail (E) can be attached to headboard or footboard, depending on where
you would like the Ladder (B) to be positioned. Open end of Short Side Guard Rail (E) must be positioned against Bunk Bed End
(A), and closed end of Short Side Guard Rail (E) must be positioned against Ladder (B).
Orientation 1 Orientation 2
Orientation 3 Orientation 4
NOTE:
8
D/E
D
6

Page 7 of 10
Attach Small Metal Brackets (7) to the Long Guard Rail (D)
and Short Guard Rail (E) using 8x19mm Short Screws (6)
that are provided.
CALLUM FULL LOFT BED – ASSEMBLY INSTRUCTIONS
STEP 4:
Attach the Long Guard Rail (D) and Short Guard Rail (E)
to the Bunk Bed Ends (A) using 8x19mm Short Screws (6)
that are provided.
STEP 5:
7
6
6
D/E
D/E
8
D
D

Position the Ladder (B) in the opening between the
Short Guard Rail (E) and the post of the Bunk Bed
End (A). Hook the Ladder (B) over the top and bottom
side rails. Then tighten using Short Screws (6) and
Philips head screwdrive.
Page 8 of 10
CALLUM FULL LOFT BED – ASSEMBLY INSTRUCTIONS
Attach Small Metal Brackets (7) to the Bunk
Bed Ends (A) using 8x19mm Short Screws (6)
that are provided.
STEP 6:
STEP 7:
6
6
A
A
B
B
7
D/E

Lay the Top Platform Panels (H) on top of the
Stretcher Bars (G) and attach using Qty.40
Long Screws (4) with Philips-head screwdriver.
STEP 9:
Page 9 of 10
CALLUM FULL LOFT BED – ASSEMBLY INSTRUCTIONS
STEP 8:
NOTE: If you need to move the unit, do not drag it.
2 or more people are needed to safely move the unit.
Lay the Stretcher Bars (G) in between the Front/Back
Guard Rails (C), then tighten using Long Screws (4)
and Philips-head screwdriver.
G
4
G
H
H
4
G
C
H
C

Page 10 of 10
STEP 10:
INSTALL BEDDING
UPPER BUNK MATTRESS DIAGRAM
MATTRESS
BEDDING SPECIFICATIONS FOR TOP BUNK:
The following size mattress and Foundation are specified for use with this Bunk bed:
MATTRESS DIMENSION SPECIFICATIONS FOR TOP BUNK
Twin - over - twin bunk: 75" long x 38" wide x 7" thick
Full - over - full bunk: 75" long x 53" wide x 7" thick
MATTRESS DIMENSION SPECIFICATIONS FOR LOWER BUNK
Twin - over - twin bunk: 75" long x 38" wide x 10" thick
Full - over - full bunk: 75" long x 53" wide x 10" thick
PLATFORM :
-Twin - over - twin bunk: Upper bed consists of 2 pcs platform 37 3/4" long x 38 3/4" wide x 3/4" thick & bottom bed consists of
14 pcs slats 38 3/4" long x 2 1/2" wide x 3/4" thick.
-Full - over - full Bunk: Upper bed consists of 2 pcs platform 37 3/4" long x 53 7/8" wide x 3/4" thick & bottom bed consists of
14 pcs slats 53 7/8" long x 2 1/2" wide x 3/4" thick.
**Note: MATTRESS THICKNESS MUST NOT EXCEED MAX 7" FOR TOP BUNK.
Be sure to adhere to these BEDDING SPECIFICATIONS in order to avoid the possibility of falling or entrapment.
THESE SPECIFICATIONS MUST BE STRICTLY ADHERED TO !
5" MINIMUM DISTANCE
FROM TOP OF MATTRESS
TO TOP OF GUARD RAIL
7" MAXIMUM
THICKNESS
SIDE RAIL
PLATFORM
CARE INSTRUCTIONS
Dust often using a clean, soft, dry, lint-free cloth.
Blot spills immediately, and wipe with a clean, damp cloth.
Do not use chemical cleansers, abrasives or furniture polish on the lacquered finish.
CALLUM FULL LOFT BED – ASSEMBLY INSTRUCTIONS