RH Baby&child JAMESON User manual

11
/
1/7

IMPORTANT SAFETY INFORMATION FOR TODDLER & DAY BEDS
·The mattress intended for use on the bed shall be a full-size crib
mattress having minimum dimensions of 51-5/8 inches (1310mm) in
length, 27-1/4 inches (690mm) in width and 4 inches (100 mm) in
thickness, not exceeding 6 inches (152 mm) in thickness.
·If guardrails are used as the mattress containment means,
guardrail(s) provided must be used to avoid the formation of a gap
between the mattress and the bed that could cause an entrapment.
·DO NOT place bed near windows where cords from blinds or drapes
may strangle a child.
·DO NOT place items with a string, cord, or ribbon around a child’s
neck, such as hood strings or pacifier cords.
·DO NOT suspend strings over a toddler bed for any pacifier cords.
·A child using the toddler or day bed shall be at least 15 months of age
and shall not weigh more than 50lbs (22.7kgs).
WARNING: ENTRAPMENT / STRANGULATION HAZARD
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
NEVER use bed with children under 15 months.
NEVER place bed near windows where cords from blinds or drapes
may strangle a child.
2/7

WARNING: ADULT ASSEMBLY ONLY, OWING TO THE PRESENCE OF
SMALL PARTS, SHARP POINTS AND EDGES.
CAUTION
TODDLER BED: THE MINIMUM AGE SHALL NOT BE LESS THAN 15 MONTHS AND THE MAXIMUM
WEIGHT SHALL NOT BE GREATER THAN 50LBS. (22.7 KG).
THE MATTRESS INTENDED FOR USE ON THE BED SHALL BE A FULL-SIZE CRIB MATTRESS HAVING
MINIMUM DIMENSIONS OF 51-5/8 IN. (1310MM) IN LENGTH, 27-1/4 IN(690MM)IN WIDTH AND 4 IN. (100MM)
IN THICKNESS NOT EXCEEDING 6 IN. (152MM) IN THICKNESS.
CARE INSTRUCTIONS:
·Dust often using a clean, soft, dry, lint- free cloth.
·Blot spills immediately, and wipe with a clean, damp cloth.
·We do not recommend the use of chemical cleaners, abrasives, or furniture polish on our lacquered finish.
TODDLER CONVERSION KIT
ASSEMBLY HARDWARE IS
INCLUDED IN THE TODDLER
KIT BOX.
PART LIST
A. JAMESON CONVERSION HEADBOARD
B. JAMESON CONERSION SIDE RAIL PANELS
C. JAMESON CONVERSION TODDLER BED KIT
D. MATTRESS SUPPORT
Allen Wrench = 1 pc
(EE) 1/4" x 1/2" Allen Bolt = 2 pcs
(FF) 1/4" x 2 1/2" Allen Bolt = 2 pcs
Lock Washer = 2 pcs Plain Washer = 2 pcs
3/7

DETAIL B
DETAIL A
ASSEMBLY INSTRUCTIONS
STEP 1
FRONT RAIL PANEL DISASSEMBLY
STEP 1.1
Remove the front rail panel of the crib by loosening all the bolts
installed, as in DETAIL A.
STEP 1.2
Gently tilt the crib and release the bolts underneath the metal brackets
holding the stabilizer rails, as in DETAIL B.
NOTE: Slightly loosen the bolt at the back of the headboard that
enough to set the toddler rail in-between side rail panels.
4/7

DETAIL C
STEP 2
TODDLER RAIL ASSEMBLY
STEP 2.1
On inside face of both side rail panels there is a cavity for the hook
and a hole for the Allen bolt to pass through which corresponds to
the hooks on both ends of the toddler rails and holes with
pre-installed nuts. Align and insert the hook of the toddler rail into
the cavity of the side rail panels, then engage Allen head bolt in the
hole and tighten with Allen wrench provided. See DETAIL C.
STEP 2.2
Fill the holes located on the top of both sides of the side panel by
inserting bolt (EE) provided.
FF
EE
EE
Lock washer
Plain washer
5/7

B
C
STEP 3
MATTRESS SUPPORT HEIGHT ADJUSTMENT
NOTE: If mattress supports is not in the lowest position.
STEP 3.1
Loosen and remove all hardware (BB) on both sides of the frame of
mattress support.
STEP 3.2
Re-install the bolt on the third hole of the frame through the hole on the
arm support. Fasten the bolt with plain washers, lock washers &
hexagonal nut. Repeat procedure on the other arms of the mattress
support. See DETAIL D & DETAIL E.
DETAIL E
Mattress Support
Stabilizer Rail
HARDWARE
Lock
Washer
Hex Nut
Plain
Washer
Allen Bolt
(BB)
Allen Wrench
DETAIL D
(BB) 1/4" x 1 1/4" Allen Bolt = 8 pcs
Allen Wrench = 1 pc
Lock Washer = 8 pcs
Plain Washer = 8 pcs
Hex Nut = 8 pcs
11 X 70
Open Wrench = 1 pc
Allen Bolt
(BB)
Allen Bolt
(BB)
Allen Bolt
(BB)
6/7

STEP 4
INSTALLATION OF STABILIZER RAILS INTO
THE SIDE PANEL
STEP 4.1
On inside face of both side rail panels are pre-installed metal
brackets, designed to hold the stabilizer rails. Set both ends
of the stabilizer rails into brackets, as illustrated in DETAIL F.
STEP 4.2
Once the stabilizer rails are set, gently tilt the toddler bed
and fasten the stabilizer rails with bolt, plain washer and lock
washer.
NOTE
After assembly, re-tighten all bolts to a snug fit.
DETAIL F
7/7