ILLUMINATED BLAIRE ALABASTER DRESSER MIRROR
IMPORTANT SAFETY INSTRUCTIONS
INSTALLATION BY A LICENSED ELECTRICIAN IS STRONGLY
RECOMMENDED.
WARNINGS
All wires are connected. When unpacking, be careful not to pull wires,
as a bad connection may result. Do not connect electricity until your
fixture is fully assembled. To reduce the risk of fire, electrical shock, or
personal injury, always turn off fixture and allow it to cool prior to replacing
the lightbulb. Do not touch or look directly at the bulb when fixture is
illuminated. Keep flammable materials away from lit bulb.
WARNING: This product can expose you to lead, which is known to
the State of California to cause cancer and birth defects or other reproductive
harm. For more information, go to www.P65Warnings.ca.gov.
THIS PRODUCT IS NOT A TOY AND HAS NO PLAY
VALUE.
WARNING: STRANGULATION HAZARD
Keep cord at least 3 feet away from cribs, bassinets, and toddler beds.
Keep out of reach of children under 3 years of age.
PORTABLE ASSEMBLY & INSTALLATION FIG. 1
1. Carefully remove all parts from the box and remove all plastic
coverings.
2. Determine the mounting location for your mirror.
3. Examine Mounting Bracket (B). It has 5 holes for attachment to the
wall. Using a stud nder, locate at least one wood stud behind the wall
surface and mark the location with a pencil. IT IS NECESSARY TO
ATTACH WALL BRACKET (B) TO AT LEAST ONE WOOD STUD.
4. Hold Mounting Bracket (B) against the wall with the mark from Step
3 visible through one of the holes in the bracket. Ensure Mounting
Bracket (B) is leveled, then mark the other holes using a pencil.
5. Use your stud nder to determine if any of the other marks from Step
4 are over any wood studs. Mark these points accordingly.
6. For each mark that is over a wood stud, drill a 1/16" pilot hole. For the
remaining marks not over wood studs, drive Hollow Wall Anchors
(D) into each of the three of the marked points using a #2 Phillips
Screwdriver.
7. Align Mounting Bracket (B) to the drilled holes and Hollow Wall
Anchors (D).
8. Secure Mounting Bracket (B) using 42mm Wood Screws (E) for the
wood stud locations and 52mm Screws (C) at the Hollow Wall Anchor
(D) locations. Hand tighten each of the screws.
9. Using two people, hang Mirror (A) to Mounting Bracket (B).
10. Plug into proper electrical outlet and test operation.
HARDWIRE ASSEMBLY & INSTALLATION FIG. 2
1. Repeat Steps 1 through 8 from Portable Assembly & Installation in Figure
1.
2. DISCONNECT POWER AT THE BREAKER OR FUSE PANEL FOR THE THE
JUNCTION BOX WHERE YOUR MIRROR WILL BE INSTALLED.
3. Straighten the power cord, cut it to approximately 15 inches, then
remove the plastic insulation around the power cord according to the
inset view in Fig. 2.
4. After placing the heat-shrinkable bushing, let the wire pass through
Metal Round Plate (H). The bushing should be positioned as shown in
Fig. 2.
5. Position Mounting Plate (K) over the junction box and align the 2
junction box screw holes with the curved slots in the Mounting Plate (K).
Temporarily secure with two Mounting Screws (I).
6. Make a mark on the wall through the 4 corner holes in Mounting
Plate (K). Remove Mounting Screws (I) from the junction box and set
Mounting Plate (K) aside.
7. Drive Metal Anchors (L) into the wall at the 4 marked positions from Step
5 using a Phillips screwdriver.
8. Attach Mounting Plate (K) to the wall by driving four Screws (M) into
Metal Anchors (L) using a Phillips screwdriver.
9. Insert two Mounting Screws (I) through curved slots in Mounting
Plate (K) and into junction box screw holes. Tighten with a Phillips
screwdriver.
10. Pull house wiring from junction box through the center hole of
Mounting Plate (K).
11. Connect the hot wire (black) from the mirror to the hot wire from the
outlet box (usually black) with Wire Nuts (J). Wrap the connection with
electrical tape.
12. Connect the neutral wire (white) from the mirror to the neutral wire from
the outlet box (usually white) with Wire Nuts (J). Wrap the connection
with electrical tape. DO NOT REVERSE THE HOT AND NEUTRAL
CONNECTIONS OR SAFETY WILL BE COMPROMISED.
13. Connect the ground wire (green) from the mirror to the ground wire
from the outlet box (usually green or bare copper) with Wire Nuts (J).
Wrap the connection with electrical tape. IT IS IMPERATIVE THAT THIS
MIRROR BE GROUNDED.
14. Push all connections into the wall junction box.
15. Secure the wire with Plastic Set Screw (F) with a screwdriver. Ax Metal
Round Plate (H) to Mounting Plate (K) and secure with Screws (G).
16. Using two people, hang Mirror (A) to Mounting Bracket (B).
17. Assembly is complete.
CARE INSTRUCTIONS
Do not use polishes or cleaners on the fixture. Wipe clean with a soft, dry
cloth.
