Rheavendors Group CINO XS GRANDE PRO Manual

INSTALLATION AND MAINTENANCE MANUAL
Translation of the original instructions
MAN2100160 rel. 00 dated 05.11.2013
__________________________________________
www.rheavendors.com
Cino XS grande PRO
Cino XS grande PRO VHO
type: compact
espresso

preliminary
safety
information
***
***
***
***
***
***
before using the machine, carefully read this information that helps you
behave properly and guarantee a safe use;
the following pages use the symbols listed here below, whose meaning is of
attention:
GENERAL;
if the text is highlit by this symbol, it is recommended to pay special
attention to the performance of the procedures described; if not carefully
performed on safe conditions, they can be source of general danger;
HIGH VOLTAGE;
if not properly performed, the actions marked by this symbol may expose
to accidental contacts with electric voltage;
DANGEROUS TEMPERATURE;
if not properly performed, the actions marked by this symbol may expose
to accidental contacts with high-temperature parts;
MOVING MEMBERS;
if not properly carried out, the actions marked by this symbol may expose
to accidental contacts with moving members;
the same symbols are placed inside the vending machine to indicate the
parts on which to act with the utmost caution;
SERVICE KEY IN USE;
the symbol recommends the utmost attention during the actions described;
the use of the service key intended to activate all machine functions when
the door is open is only reserved to the technical operators who know the
operation of the vending machine, who are aware of potential risks and who
make sure they are operating on totally safe conditions;
the use of the service key shall be strictly limited to the time necessary to
perform the actions requiring the use thereof; users shall be informed of
the prohibition on using and approaching the vending machine;
safety rules for using the vending machine
pay special attention to the chapters and notes high lit by the symbols of
alert; strictly observe the rules concerning, in particular, the operators’ and
users’ safety;
under no circumstance may the vending machine be used by children or by
people with poorer physical, sensorial or mental capacities or who have not
been properly informed on correct use; children shall be supervised to
prevent them from playing with the vending machine;
if you should find out a water leak or the presence of smoke, immediately
detach the vending machine from the electric and hydraulic network, never
try to restore its operation and apply to skilled technicians;
the machine shall be installed according to national rules; pay special
attention to the rules about the machines directly connected with the
hydraulic network;
the user is not allowed to access the maintaining and servicing area that
shall be properly signalled;
never remove protections, never override safety devices and never modify
the machine or its components;
MAN2100160 rel. 00 dated 05.11.2013 page no. 2 of 53 pages
www.rheavendors.com tel: [phone] fax: [phone] e mail: rh[email protected]m
exclusive property of rheavendors group
Cino XS grande PRO and PRO VHO by

the symbol means that it is forbidden to dispose of
the equipment as urban waste and compulsory to
provide for separate collection in order to prevent
any potential effect on the environment and human
health; strictly follow the provisions of the
European Parliament’s 2002/96/EC Directive;
MAN2100160 rel. 00 dated 05.11.2013 page no. 3 of 53 pages
www.rheavendors.com tel: [phone] fax: [phone] e mail: rh[email protected]m
exclusive property of rheavendors group
Cino XS grande PRO and PRO VHO by

residual risks a residual risk is understood as a potential danger
that can not be eliminated and it persists despite all
precautions in use since it is related to the intrinsic
features of the product and it also includes non-
identifiable risks;
the actions and behaviours listed here below are
intended to reduce residual risks and you shall
always adopt them when interacting with the
machine;
wear clothes that can properly avoid any accident
(never wear rings, chains, clothes with laces or
excessively long sleeves, …);
carefully evaluate the treatment of residues from
installation (wood, plastics, …) and utilisation
(product powder, bags, …);
never repair or carry out any technical action if you
have not been properly trained;
signal that a technical action is in progress on the
machine (barriers against approach, signs, …),
carry it out quickly without leaving the station;
install the machine in a sheltered, illuminated,
ventilated and noiseless environment; keep it clean
and never place tools or any other object on it;
never install it outdoors or, anyway, never expose
it to atmospheric agents;
make sure it can be neither reached by water
sprays or vapours nor hit by objects that might
damage it;
carefully consider the machine weight and stability
during the installation and in the final working
position;
supply the machine within voltage, temperature,
pressure and hydraulic limits, …as it is detailed on
the following pages and provide for an effective
earthing;
even if detached from supply, the machine may
contain hot pressurised water at a high
temperature;
never detach hydraulic and electric supplies when
they are active;
MAN2100160 rel. 00 dated 05.11.2013 page no. 4 of 53 pages
www.rheavendors.com tel: [phone] fax: [phone] e mail: rh[email protected]m
exclusive property of rheavendors group
Cino XS grande PRO and PRO VHO by

this manual is intended to describe the Cino XS grande vending machine in its two versions PRO and PRO VHO;
by using the same basic components, the two machines differ from each other in components and in the features
specified later on; the descriptions supplied by this document are shared by all three versions, if not otherwise specified
by the text or by the icons typical of every single model.
Cino XS grande PRO
coffee beans
canister sensor
no
yes
pressurized boiler
400 cc; 1.600 W;
800 cc; 2.000 W;
static relay
no
yes
cover upper rail
yes
no
visible coffee
beans canister
no
yes
Cino XS grande PRO VHO
00 05.11.2013 First issue;
rel. date description
this document is made available electronically on site www.rheavendors.com
MAN2100160 rel. 00 dated 05.11.2013 page no. 5 of 53 pages
www.rheavendors.com tel: [phone] fax: [phone] e mail: rh[email protected]m
exclusive property of rheavendors group
Cino XS grande PRO and PRO VHO by

general guarantee
conditions
1st
2nd
3rd
4th
5th
6th
7th
these conditions regulate Rheavendors Industries S.p.A.’s
obligations with reference to guarantee and repair; any other term
or condition, either verbal or written, is not applicable, including
those in the purchaser’s purchase orders, if not explicitly accepted
and signed by Rheavendors Industries S.p.A.; if the guarantee
terms here below should be held not to be valid and/or lawful in
the Country where the product is sold, they will not be effective
whereas all the other clauses will remain valid and applicable;
the mechanical and electronic components of the machine are
guaranteed for twelve months, starting from the sales date certified
by the fiscal receipt;
the guarantee shall be understood as the free replacement or
repair of any part of the machine that –at the manufacturer’s
unquestionable discretion –should prove to be originally
defective due to manufacturing defects; the cost of sending the
manufacturer machines, defective pieces and spare parts will be
totally charged to the user’s account; the manufacturer reserves
the right to use new or reconditioned components for repair; if
replaced, original components will be guaranteed for 12 months;
the parts replaced under guarantee will become the property of
Rheavendors Services S.p.A. (request for “Form PO 19.01/2b”
Materials under guarantee –Authorisation to return);
in case of irreparable failure or if a failure of the same origin is
repeated, the manufacturer may –at its unquestionable discretion
–replace the machine with another one, the model of which is
either the same or an equivalent one; the guarantee of the new
machine will be extended up to the original term of guarantee of
the replaced machine;
all the parts that should prove to be defective due to negligence or
carelessness (non-observance of the instructions for the operation
of the machine), incorrect installation or maintenance by
unauthorised personnel, transport damage or any circumstance –
anyway –not due to the manufacturing defects of the machine are
not covered by guarantee; the installation and connection with
supply plants as well as the maintenance operations mentioned by
the installation manual are also excluded from any performance
under guarantee; the guarantee will not cover payment systems
either; whether installed on the machine or supplied as an
accessory, they are subject to their manufacturer’s guarantee
whereas Rheavendors Industries S.p.A. will just act as a broker;
all changes made to the machine and not agreed with the
manufacturer in writing will involve the immediate termination of
the guarantee period and anyway fall under the Customer’s total
responsibility;
the guarantee is excluded in all cases of improper use of the
machine;
Rheavendors Industries S.p.A. will disclaim all responsibility for any
damage that may be directly or indirectly caused to people,
animals or things as a result of:
improper use of the vending machine; incorrect installation;
improper energy or water supply; serious maintenance deficiency;
actions or changes not explicitly authorised; use of non original
spare parts;
in case of failure, Rheavendors Industries S.p.A. is obliged neither
to compensate any economic damage due a forced stop of the
machine nor to extend the guarantee period;
if the machine should be transferred to a centre designated by the
manufacturer for overhaul or repair, the relative transportation
risks and costs will be charged to the user’s account; the freight
charges of machines, defective pieces and spare parts are always
understood as charged to the user’s account;
MAN2100160 rel. 00 dated 05.11.2013 page no. 6 of 53 pages
www.rheavendors.com tel: [phone] fax: [phone] e mail: rh[email protected]m
exclusive property of rheavendors group
Cino XS grande PRO and PRO VHO by

declaration of
conformity
marking
ISO 9001 certification
Rheavendors Industries S.p.A. declares that this drink vending
machine has been designed and manufactured in compliance with
the following directives and safety standards:
Directives:
2004/108/EC; 2006/95/EC; 2006/42EC;
2002/95/EC (RoHS); 2002/96/EC (RAEE); 1907/2006/EC (REACH);
1935/2004/EC;
Standards:
SAFETY:
EN 60335-1: 2002 + A11: 2004 + A1: 2004 + A12:2006 +
A2: 2006 + A13: 2008 + A14: 2010 + A15: 2011;
EN 60335-2-75: 2004 + A1: 2005 + A11: 2006 + A2: 2008 +
A12: 2010;
EMC:
EN 55014-1: 2006 + A1: 2009 + A2:2011;
EN 55014-2: 1997 + A1: 2001 + A2: 2008;
EN 61000-3-2: 2006 + A1: 2009 + A2: 2009;
EN 61000-3-3: 2008;
EMF:
EN 62233: 2008;
manufacturer
Rhea Vendors Group S.p.A.
Via Valleggio, 2/bis –22100 Como –(CO) - Italia
manufacturer of the machine
Rheavendors Industries S.p.A.
Via Garavaglia, 58 - 21042 Caronno Pertusella –(VA) –Italy
The President & CEO
(C. D. Majer )
conformity
MAN2100160 rel. 00 dated 05.11.2013 page no. 7 of 53 pages
www.rheavendors.com tel: [phone] fax: [phone] e mail: rh[email protected]m
exclusive property of rheavendors group
Cino XS grande PRO and PRO VHO by

table of contents
01.
02.
03.
04.
05.
06.
07.
08.
09.
10.
11.
12.
13.
14.
legend
introduction
technical data
configurations
presentation
preliminary actions
connections
installation and first power on
programming
parameters
solution of problems
maintenance
how to do to…
hydraulic diagram
in the listed chapters, the manual describes a
Cino XS grande PRO and PRO VHO
vending machine in its hardware and software components for a
complete and fully-aware use of all machine functions; due to the
large variety of available options and the constant technical update
of our vending machines, some special device or function might be
indicated and described not in the manner you expect; in this case,
do not hesitate to contact us;
telephone: [phone]
fax: [phone]
e mail: [e-mail]
ATTENTION: this label applied next to the serial number label
inside the vending machine points out that the instructions
supplied by this manual must be carefully read before the
installation and operation of the vending machine;
please, print this manual only if necessary; environmental
protection is our common interest;
page 09
page 09
page 10
page 12
page 14
page 22
page 23
page 24
page 27
page 40
page 43
page 46
page 50
page 53
MAN2100160 rel. 00 dated 05.11.2013 page no. 8 of 53 pages
www.rheavendors.com tel: [phone] fax: [phone] e mail: rh[email protected]m
exclusive property of rheavendors group
Cino XS grande PRO and PRO VHO by

01.
legend
01.01. abbreviations and
pictograms
E =
R =
=
VSF =
=
=
=
01.02. tools
02.
introduction
02.01. copyright
information
02.02. contacts
02.03. serial number
labels
some general instructions that may be of use for reference to this
manual;
dispensing cycle of drinks based on instant products and coffee
beans;
machines with external water supply;
mixer for mixing the instant product with water;
worm screw pitch in the product canister;
product shaker of instant canisters;
espresso coffee brewer
hot water dispenser
some tools commonly used and easy to find are necessary to act
with this vending machine:
- a pair of scissors for electricians;
- a star screwdriver 4/6 mm;
- a set of fixed wrenches up to 13 mm;
- a set of socket head screws from 2 to 8 mm;
it may be of use to procure some expendables, such as disposable
paper, single-use gloves, clean cloths, cups and a bucket for the
collection of waste water;
© Rheavendors Industries S.p.A.; all rights reserved;
this document contains some confidential information of
Rheavendors Industries S.p.A.’s exclusive property; the content of
this document can be neither disclosed in favour of third parties,
nor copied or reproduced in any form whatsoever, either fully or
partially, without Rheavendors Industries S.p.A.’s prior
authorisation in writing; the utilisation, reproduction or disclosure
of the technical information in this document can be protected by
Rheavendors Industries S.p.A. according to the Law;
this manual is intended for the owner of the vending machine; it is
an integral part of the machine and it shall be kept with it;
the information supplied by this manual are intended to achieve
the best performances of the vending machine within the scope of
application established by the Manufacturer; Rheavendors
Industries S.p.A. reserves the right to improve future production
without serving any prior notice and without assuming any
obligation to update the products on the market; the manufacturer
will disclaim all responsibility for any inaccuracy due to misprints;
Rheavendors Services S.p.A. is at disposal for any kind of
support and information on this vending machine;
telephone: + 39 02 966 551
fax: [phone]
e mail: [e-mail]
for any reference about our partners all over the world please visit
site : www.rheavendors.com
to be able to identify the vending machine rapidly and univocally as
well as to get the best support, please specify the data of the serial
number label;
code : D12345A67890
s/n: 1234 56 7890
silvery serial number labels are applied inside and outside the case
of the machine;
§
MAN2100160 rel. 00 dated 05.11.2013 page no. 9 of 53 pages
www.rheavendors.com tel: [phone] fax: [phone] e mail: rh[email protected]m
exclusive property of rheavendors group
(example)
Cino XS grande PRO and PRO VHO by

03.
technical data
03.01. dimensions
PRO
VHO
03.02. weight
03.03. supply
water
energy
03.04. sound pressure
03.05. keyboard
03.06. display
03.07. dispensing cpt.
03.08. drip tray
03.09. dispenser
03.10. safety
water
energy
heat
software
03.11. grinder motor
03.12. grinders
03.13. espresso brewer
03.14. air break
03.15. pump
03.16. product motors
03.17. mixing bowls
03.18. mixer motors
03.19. product sensor
03.20. boiler
height (including upper rail of 28 mm):
height (including visible coffee beans canister of 80 mm):
width:
depth:
depth with open door:
PRO
VHO
- connection by means of a solenoid valve with 3/8“gas male face:
- supply by a submersible pump:
- 230 V, 50 Hz; single-phase and ground;
- cable of the following type: H05VV-F 3G 1 mm² 300/500 V
(values and indications for standard machines)
anyway refer to label data
A-weighted sound pressure level;
ten selection buttons;
multicolor; work area 66.5 mm x 33.2 mm;
open; folding cup support: (useful height 85 mm);
drip tray beneath the cup surface:
a fixed dispensing place;
overflow sensor and pressure relief valve;
water inlet solenoid valve with anti-flood sensor;
a main switch, a door switch;
two 6.3x32 mm fuses;
manually resettable sensors;
time limits for water dispensing cycles;
conical:
variable-volume brewing chamber;
motor:
air break with overflow and level switch;
vibration;
max. three, according to the machine configuration;
max. two, according to the machine configuration;
max. two, according to the machine configuration;
only in VHO; one; installed to control the coffee beans canister
content;
pressure boiler; PRO
VHO
618 mm
670 mm
420 mm
563 mm
880 mm
33 kg
34 kg
from 0.1 MPa to 0.8 MPa
24 V dc, 1.2 A max.;
PRO: 1,700 W; VHO: 2,100 W
see 02.03.
less than 70 dB(A)
resolution 64 x 128 pixel;
maximum 150 mm
capacity 750 ml
230 V ac; 12 A delayed
127 °C
230 V dc; 150 W
400 r.p.m.
Ø 45 mm; 8 ÷ 15 gr.
24 V dc; 30 W
230 V ac
95 r.p.m. 24 V dc
15,000 r.p.m. 24 V dc
capacitive; plastic canister;
0.4 litres, 1,600 W
0.8 litres, 2,000 W
MAN2100160 rel. 00 dated 05.11.2013 page no. 10 of 53 pages
www.rheavendors.com tel: [phone] fax: [phone] e mail: rh[email protected]m
exclusive property of rheavendors group
Cino XS grande PRO and PRO VHO by

03.21. product canisters
03.22. relay
03.23. miscellaneous
03.24. notes
max. four, according to the machine configuration; single (55 mm)
or double (110 mm) width; dispensing worm screws 9 mm or 18
mm in pitch; with mixer gear and stirrer, if arranged by the
configuration and with standard or shorter product slide outlet
(see 05.22.);
- coffee beans canister (or hopper) capacity:
- instant canister capacity:
solid state relay to supply the pressure boiler heating element;
machine parameters programmable by means of a flash key or
selection keyboard; NRI G13 or similar payment system
compartment; protocols: serial, parallel, executive, MDB; data
collection by means of a flash key (see 09.06.);
the water and energy supply tolerance limits that can ensure a
good and proper operation of the Cino XS grande PRO and PRO
VHO machine are:
water:
- total hardness:
- recommended conductivity:
(*) if harder, please use anti-limestone filters;
energy:
- nominal voltage:
room (during storage and operation):
- temperature:
- relative humidity:
electric consumption:
- power (vending phase): PRO
VHO
the complete data according to the EVA-EMP Energy Measurement
Protocol, are made available upon request (see 02.02.);
the power supply cable supplied with the vending machine
shall not be altered under any circumstance; in case of loss
or damage replace it by using an original component only;
make sure that the electric installation can deliver the power
suitable for the machine (see 03.03.);
a good ground connection is not only a legal obligation for the
protection of users and operators, but it can also provide for
correct power supply;
PRO: 1.0 kg
VHO: 2.0 kg
VHO
from 10 °F to 25 °F (*)
400 μS @ 20 °C
+10 % /- 15 %
5 °C ÷ 35 °C
max 80 %
da 13 Wh a 380 Wh
da 44 Wh a 396 Wh
MAN2100160 rel. 00 dated 05.11.2013 page no. 11 of 53 pages
www.rheavendors.com tel: [phone] fax: [phone] e mail: rh[email protected]m
exclusive property of rheavendors group
width 55 mm
width 110 mm
capacity 1.7 litres
capacity 3.5 litres
coffee
0.33 kg
milk
0.38 kg
milk
0.80 kg
chocolate
0.94 kg
chocolate
2.20 kg
tea
0.98 kg
sugar
1.20 kg
Cino XS grande PRO and PRO VHO by

04.
configurations
04.01.
a. product canisters
b. water supply
c. numbering
04.02. examples of
configurations
Cino XS grande PRO and PRO VHO configurations are
numerous; they are coded by means of some categories
exemplified here below in the abbreviation of the machine:
number of instant products and coffee beans:
external, by means of the inlet solenoid valve:
product canisters, mixing bowls and mixers are numbered in
progression, from the left to the right, as it is shown later on; this
numbering is used in the chapter on how to programme (see 09.)
drinks;
V.M. Cino XS grande PRO E/4 R
V.M. Cino XS grande PRO E/5 R
Cino XS grande PRO E/4;
Cino XS grande PRO E/4 R
keyboard selections
1. espresso
2. black coffee
3. white coffee
4. cappuccino
5. latte macchiato
6. moccaccino
7. chocolate
8. choko-milk
9. instant coffee
10. hot water
keyboard selections
1. preselection sugar
2. espresso
3. espresso with milk
4. long
5. capp-ciocc
6. cappuccino
7. white coffee
8. latte macchiato
9. moccaccino
10. chocolate
MAN2100160 rel. 00 dated 05.11.2013 page no. 12 of 53 pages
www.rheavendors.com tel: [phone] fax: [phone] e mail: rh[email protected]m
exclusive property of rheavendors group
Cino XS grande PRO and PRO VHO by
coffee
beans
milkchocolate coffee
800
grams
2200
grams
330
grams
1000
grams
mixer
1
mixer
2
3 5
water 1 water 2
water 3
§
vsf 9
vsf 18 vsf 18
4
§
coffee
beans
1000
grams
mixer
1
mixer
2
water 1 water 2
water 3
milk coffee
1200
grams
800
grams
330
grams
3 6
§
vsf 9
vsf 18
4
vsf 9 vsf 9
5
940
grams
chocolate
sugar

MAN2100160 rel. 00 dated 05.11.2013 page no. 13 of 53 pages
www.rheavendors.com tel: [phone] fax: [phone] e mail: rh[email protected]m
exclusive property of rheavendors group
04.03. accessories
V.M. Cino XS grande PRO VHO E/4 R
V.M. Cino XS grande PRO VHO E/3 R
the configurations above are just some of possible Cino XS
grande PRO and PRO VHO configurations, considering the
vending machine releases and programmability; the principles of
operation and information are anyway universal and applicable to
all machines of the Cino XS grande PRO and PRO VHO range;
to complete and supplement the vending machines of the Cino XS
grande PRO and PRO VHO range, Rheavendors Industries S.p.A.
has got a series of accessories manufactured for these machines,
such as cabinets, autonomous water supply kits, payment systems,
external drawer to collect the exhaust grounded coffee connection
with machines intended to dispense cold drinks, …;
Rheavendors Services S.p.A. is at disposal for any kind of support
and information on special configurations (see 02.02.);
keyboard selections
1. espresso short
2. espresso
3. espresso long
4. latte macchiato
5. americano
6. cappuccino
7. moccaCino
8. choko-milk
9. tea
10. hot water
keyboard selections
1. espresso short
2. espresso
3. espresso long
4. latte macchiato
5. americano
6. cappuccino
7. moccaCino
8. Choko-milk
9. milk
10. hot water
Cino XS grande PRO and PRO VHO by
coffee beans
milk chocolate tea
380
grams
2200
grams
980
grams
2000
grams
mixer
1
mixer
2
3 4 6
water 1 water 2
water 3
§
vsf 9vsf 18
vsf 18
§
milk chocolate
800
grams
2200
grams
mixer 1
54
water 2
water 1
§
vsf 18 vsf 18
§
coffee beans
2000
grams

05.
presentation
CINO XS GRANDE PRO
MAN2100160 rel. 00 dated 05.11.2013 page no. 14 of 53 pages
www.rheavendors.com tel: [phone] fax: [phone] e mail: rh[email protected]m
exclusive property of rheavendors group
05.07.
electric connection
05.09.
fuses
05.08.
power on switch
05.28.
powder aspirator
05.24.
product motor
05.37.a.
CPU 05.20.
grinder
05.30.
air break
05.31.
volumetric counter
05.34.
pressure boiler pump
05.35.
instant solenoid valves
05.35.
pressure boiler
05.35.
boiler water drain
05.10.
water drain plug
05.11.
water inlet solenoid valve
05.30.
switch floater
05.27.
mixer motor
05.22.
instant product canister
05.16.
coffee brewer
05.21.
grounds container
05.06.
drip tray
05.12. door switch
and service key
05.22.
coffee beans canister
protection carter
05.05.
door lock
05.25.
mixing bowl
05.27.
mixer motor
05.26.
nozzle support
05.33.
coin box housing
05.13.
internal button (PROG)
05.06.
level sensors
05.14.
flash key housing
05.29.
air aspirator
Cino XS grande PRO and PRO VHO by

CINO XS GRANDE PRO VHO
05.12.
visible
coffee beans canister
05.24.
product motor
05.37.b.
display p.c.b.
05.27.
mixer motor
05.18.
heater
05.12.
service key
05.05.
door lock
05.23.
coffee beans sensor
05.30. aspirator
drawer housing
05.20.
grinder
05.31.
powder aspirator
05.29.
product motor
05.39.
CPU
05.23.
coffee beans sensor
05.21.
grinder motor
05.33.
air break
05.34.
volumetric counter
05.35.
pressure boiler pump
05.37.
pressure boiler
05.32.
air aspirator
05.37.
instant solenoid valves
05.26.
coffee brewer motor
05.33.
switch floater
Cino XS grande PRO and PRO VHO by
MAN2100160 rel. 00 dated 05.11.2013 page no. 15 of 53 pages
www.rheavendors.com tel: [phone] fax: [phone] e mail: rh[email protected]m
exclusive property of rheavendors group

05.01. general
information
05.02. selection keyboard
05.03. display
05.04. dispenser
05.05. door lock
05.06. drip tray
05.07. electric connection
05.08. power on switch
05.09. fuses
05.10. water drain plug
05.11. water inlet
solenoid valve
05.12. door switch
the Rhea Cino XS grande PRO and PRO VHO vending machine is
a machine explicitly designed for being easily used by all users
since no specific competence is required in preparing drinks;
the function consists in dispensing drinks by mixing food products
and water at a proper temperature; the correct operation of the
vending machine occurs in closed rooms in normal environmental
conditions and at a room temperature between 5 °C and 35°C, the
relative humidity below 80%;
use only specific ingredients for vending machines;
dispense by briefly pressing a key of the selection keyboard
(see 05.02.); make sure that the cup has been properly positioned
at the dispensing station, if necessary by using the flap support for
caps (see 03.07.);
after having closed the door, press the buttons to dispense; the
button will turn on during the dispensing cycle; keys will assume
various functions in the programming mode (see 09.) and enable
the user to modify the machine parameters; keys are numbered
progressively from the top: 1, 2, …and from the left;
the display messages inform users and operators about the
operation state of the vending machine;
the Cino XS grande PRO and PRO VHO vending machine has got
a fixed drink dispenser on the cup support surface;
the door is closed by means of a lock; the key is mapped and
numbered for identification;
it collects possible residual drops from the dispenser and, if
necessary, the waste water in excess from the boiler; it is slided at
the bottom of the machine case, in the front, and it is composed by
a covering drawer and a grilled cover that can be washed by
running water; an electric contact is intended to control the filling
level (see 11. and 13.03.);
a three-terminal socket is arranged at the back of the case for the
connection of the mains cable;
to power on and off the machine;
installed on the mains power supply (see 03.10.); fuses must be
necessarily replaced by specialised technical personnel only;
from where to let the silicone tube from the air break come out for
emptying;
the water inlet solenoid valve has got an anti-flood safety device
intended to stop the water inlet in case of failures; to its electrical
pins can be connected in parallel an any submersible pump (see
03.03.);
to power off the machine when the door is open;
attention
some parts remain anyway network-connected
act extremely carefully;
use the service key to supply the vending machine if it is necessary
to activate the machine when the door is open;
the key is housed in the cover;
03
02
1
2
3
4
5
6
7
8
9
10
04
05
06
08
09
07
11
12
10
MAN2100160 rel. 00 dated 05.11.2013 page no. 16 of 53 pages
www.rheavendors.com tel: [phone] fax: [phone] e mail: rh[email protected]m
exclusive property of rheavendors group
Cino XS grande PRO and PRO VHO by

05.13. internal button
(PROG)
05.14. flash key housing
05.15. label pockets
05.16. coffee brewer
05.17. brewer presence
switch
05.18. coffee brewer
heater
05.19. coffee brewer
motor
05.20. grinder
05.21. grounds container
05.22. product canisters
05.23. product sensor
coffee beans
05.24. product motors
the button giving access to the machine programming mode is
arranged on the orange protection carter inside the door (PROG);
programming flash keys are arranged in the carter inside the door
(see 09.06.);
product labels are arranged inside the door panel, beneath the
orange carter;
insert the labels into the pockets by observing the machine
configuration (see 13.02.);
after receiving the coffee dose from the grinder and compressing it,
percolation occurs in the coffee brewer with the water from the
pump; the used dose is conveyed towards the slide and the drawer
at the bottom of the machine; the structure of the brewer is kept at
the correct temperature by a hot air heating system programmable
via software (see 09.01.e.);
the coffee brewer presence is controlled by a micro-switch that can
inhibit the selections including coffee beans, if it is not present;
a safety cover is intended not only to protect the operator against
moving parts, but also to keep the coffee brewer at the correct
temperature through an air heater preserving the drink quality
even after a long vending machine pause;
the variable coffee brewer motor is intended to regulate the
chamber closing and compressing phases in order to compress
ground coffee for its percolation; its action is controlled by an
encoder that informs the CPU on the brewer position;
it grinds the coffee beans in the canister to pour it in the coffee
brewer chamber; the grinding degree can be manually adjusted by
means of the wheel you can access after removing the coffee
canister whereas the ground quantity is determined by a software
parameter (see 09.01.a “grinder time”) that establishes the grinder
work time;
it collects over sixty ground doses after having used them in the
coffee brewer; a software option (see 09.01.o.) will show a warning
message as soon as the tray is full;
instant product canisters dispense their content in the underlying
mixing bowls; an internal worm screw driven by the product motor
will push the instant product to the product slide; they can be
equipped with a wheel and a product shaker for constant
dispensing; the outlet, the dimension of which can be either
standard or smaller, has got a closing baffle; the coffee beans
canister (hopper) has got a closing orange blade that is to be
inserted before lifting the canister; canisters are closed by a cover
to protect products;
only in VHO, a product sensor intended to check the quantity of
coffee beans in the canister is arranged behind the coffee beans
canister;
if the product is lacking, it signals it through the vending machine
display;
they are intended to rotate the worm screws inside instant product
canisters to pour the product quantity necessary for selection in the
mixing bowls;
MAN2100160 rel. 00 dated 05.11.2013 page no. 17 of 53 pages
www.rheavendors.com tel: [phone] fax: [phone] e mail: rh[email protected]m
exclusive property of rheavendors group
13
14
15
20
18
19
17
24
22
16
21
23
Cino XS grande PRO and PRO VHO by

05.25. mixing bowls
05.26. nozzle support
05.27. mixer motor
05.28. powder aspirator
05.29. air aspirator
05.30. air break
05.31. volumetric counter
05.32. door lighting
05.33. coin box
the mixing bowls of the mixers will accommodate the instant
products you have poured to mix them with water; the fan of mixer
motors will act at the bottom and the drink outflow to the
dispenser occurs by means of a silicone tube; mixing bowls and
outlet tubes can be washed with lukewarm running water;
a fixed support on the cup station is intended to accommodate the
three dispensers coming from the mixing trays of mixers and the
direct hot water;
the motors of mixers help you mix instant products with water by
means of the rotation of the fan mounted on their axis; the
rotation speed can be adjusted (see 09.01.a.) to the features of the
various products;
an aspirator will eject suspended product residuals from the
vending machine; the aspirator is connected with a drawer beneath
product slides to intercept the residual impalpable powder coming
from selections; the action time of the aspirator is programmable
by means of a software parameter (see 09.01.f.); aspirated air is
ejected through the slots of the rear panel;
to aspirate the air from the internal environment of the machine to
avoid any condensate;
it accumulates water for sending to the pressure boiler; the level is
controlled by a float and –if above the established level –it will
flow back to the inlet solenoid valve safety device, thus preventing
the inlet of new water;
it supplies the CPU the water quantity running through the coffee
brewer to establish its volume; the water quantity of instant
selections is established by the time set in the “water N” parameter
only (see 09.01.a.);
- the door panel is lit up by two led modules mounted inside (“a”);
- the side panels are lit up by two led modules mounted inside
(“b”);
- the cup station and the logo are lit up by a module mounted
inside (“c”);
- the product labels and selection keys are lit up by two modules
(“d”) mounted at the back of the door;
in some versions, the components intended to support the payment
system (not supplied) are arranged inside the door; the coin box is
complete with a lock and the flat cable of the payment system is
inserted into a 10 pin J4 connector of the display board;
MAN2100160 rel. 00 dated 05.11.2013 page no. 18 of 53 pages
www.rheavendors.com tel: [phone] fax: [phone] e mail: rh[email protected]m
exclusive property of rheavendors group
27
30
31
26
25
32
b
c
b
a a
d d
32
27
29
28
33
Cino XS grande PRO and PRO VHO by

05.34. pressure boiler
pump
05.35. pressure boiler
05.36. static relay
a vibration pump with by pass, directs the water to the solenoid
valves and the three ways for the espresso circuit;;
attention
these components may be very hot even if the machine is off;
pressure boiler complete with a temperature probe and protection
clicsons; the drain tap may be used to empty the hydraulic circuit
(vedi 09.01.f.);
the water quantity of instant selections is established by the time
set in the “water N” parameter (see 09.01.a.);
only in “WHO” machines, the solid state relay arranged inside the
vending machine behind the supply bock can directly supply the
pressure boiler heating element so as not to overload the power
supply board;
MAN2100160 rel. 00 dated 05.11.2013 page no. 19 of 53 pages
www.rheavendors.com tel: [phone] fax: [phone] e mail: rh[email protected]m
exclusive property of rheavendors group
solenoid valve
name sw
outlet
E1
water 1
mixing bowl 1
E2
water 2
mixing bowl 2
E3
water 3
hot water 3
EX
coffee water
coffee brewer
Cino XS grande PRO and PRO VHO by
solenoid valve E3
solenoid valve E1
solenoid valve E2
temperature probe
pressure boiler pump
water inlet boiler water drain
water inlet
3-way solenoid valve
drain
three-way valve EX
bypass 1.1 MPa
protection clicsons

MAN2100160 rel. 00 dated 05.11.2013 page no. 20 of 53 pages
www.rheavendors.com tel: [phone] fax: [phone] e mail: rh[email protected]m
exclusive property of rheavendors group
05.37. electronics
05.37.a. CPU
05.37.b. display p.c.b.
05.37.c. flash board
the CPU board is intended to govern the machine operation. It is
the place of location of machine programs and it is secured to the
frame by means of four board supports;
the phone cable is intended to connect the box for the flash key
(see 05.14. and 05.37.c.) whereas the display cable will transmit
the signal exchange with the keyboard and the display arranged in
the door (see 05.02. and 05.03.); the temperature probe cable is
separated from the machine wiring to avoid hampering the removal
of the probe;
the boiler led will turn on whenever you activate the boiler heating
element;
the five leds display the machine state;
the display board secured inside the door will accommodate the
signals of the selection keyboard and display the messages; a flat
cable will connect it with the CPU;
the internal programming button is installed on the printed circuit
of this board;
arranged inside the door, beneath the orange carter (see 05.14.), it
enables the user to insert the flash key to programme the machine
(see 09.06.);
37.b
37.c
to the keyboardto the keyboard
to the CPU to the flash board
labels lighting
labels lighting
door lighting
temperature probe
connector
display board connector
RFID connector
MDB payment system
connector
executive payment
system
connector
DL2 - led 5 V dc
USB port
DL1 - led 24 V dc
DL5 - pressured boiler
heating element led
DL4 - led pump
pressured boiler
heating element
IN 230 V ac
grinder motor connector
DL3 - led 5 V CPU
grinder motor 2A fuse
name color desctription
DL1 red + 24 V universal
DL2 green + 5 V power supply
DL3 red + 5 V microprocessor
DL4 green espresso pump
DL5 red
pressured boiler heating element
Cino XS grande PRO and PRO VHO by