RHINO 4/9/16CH H.264 DVR Installation guide

Quick Manual for 4/9/16CH H.264 DVR
1. Starting DVR
. DVR (Digital Video Recorder) essentially requires Hard Disk for recording.
. Before installing Hard Disk, be sure to refer to “Approved HDD List”on the
first page of instruction manual to pick up the approved Hard Disk.
. If you install Hard Disk that is not on the list, the DVR might malfunction.
. Before installing HDD, turn off the power of DVR and fix the HDD to
provided bracket. And check the connection between SATA port and power
supply.
. In case you want to install HDD that is not on the list, please consult with
your supplier.
4CH DVR ( 1 HDD can be installed.) 9/16CH DVR (2 HDD can be installed.)
. Please make sure to use the power supply which was provided by
manufacturer.
▶4CH DVR: DC12V/ 3.5Amp, ▶9/16CH DVR: DC12V 6Amp.
. Even if the DVR does not alert you with WARNING message of FORMAT, be
sure to format the HDD before using DVR regardless of whether it is brand
new or used one. To format the HDD from DVR, go into the DVR OSD menu
and go to “System –> Hard Disk –> Erase”. If you click on “ERASE”, the DVR
will format the HDD
.
4CH 9/16CH
2. Checking Video Signal
. Our DVR supports NTSC & PAL video systems.
. We set it to either PAL or NTSC system before releasing as our customer‟s
demand. If something is wrong, please check out video system of DVR &
camera. You can change the video system by yourself on the menu “System
-> Information -> Video Mode”.
4CH 9/16CH
3. DVR Time Setup
. If the DVR time is not set, you will have difficulty in recording and searching
at the time you want. If DVR was connected to the internet, the DVR can
set-up the time automatically. Then the DVR maintains correct time
synchronize with actual time of the connected Time Server by every 24hours.
. When it comes to applying the GMT, please set the TIME ZONE.
. If DVR is not connected to the internet the time might not be correct..
4CH 9/16CH
4. Recording
. Enter DVR OSD menu and go to “RECORD SETTING”to set up each channels.
. On “RECORD SETTING”menu, select ON / OFF per channel. If recording
mode is OFF, the unit will not record even if you set the “EMERGENCY
RECORDING”.
4CH 9/16CH
. The DVR supports “Schedule Recording”and you can set-up its recording
mode by hour.
. Default of schedule recording is “Motion Detection”, every 30 minutes user
can set up such as “None, Continue, Motion, Sensor, Motion+Sensor”.
4CH 9/16CH
. Remote control, Mouse or Front Key can be used to start recording.
4CH 9/16CH
. Schedule/ Emergency Recording can also be set from one button in the
Front Key if it is DVR-400H. But there are two buttons on DVR-0800S, DVR-
1600S for Schedule or Emergency Recording in the Front Key.
. If the “REC”LED is on it means it is under schedule recording mode.
If the LED flickers it is under emergency recording mode.
. Emergency recording enables to unconditional record regardless of setup
made by user. (Please note that it will not record even if you press
“Emergency Recording”button in case recording of the relevant channel is set
“OFF”.
. “ER”means Emergency recording, “SR”means Schedule recording in status
bar.
Caution
Check Here

Quick Manual for 4/9/16CH H.264 DVR
5. Playback
. The user can search any recorded data in several way, “Recording Date
search”, “desired Date & Time –Calendar search”, “Event search”, “Go to First
data search”and “Go to Last data search”.
Press Search button in Front or Search button in Remote Controller.
4 ch 9/16 ch
Remote controller
Select search menu. Indicate Red in recorded Date.
Indicate Recording time each recorded channel.
After selecting „Time‟, available to select „Minute‟.
. To search the recorded data, use direction buttons and ENT button in DVR
Front key or direction buttons in Remote Controller or USB Mouse click.
. To playback Recorded data, press ENT button in desired time on Time Bar.
* MENU button has “ESC”function in DVR.
Press MENU button in Live mode, go into Main MENU.
To Select MENU, use direction buttons and Enter button.
To go previous menu, use “Menu”button.
6. Network Set-up to remote monitor via IP VIEWER
IP VIEWER connects DVR through network without additional downloading
software, the program download software automatically when connect DVR.
. To remote control DVR by PC, it should be connected with Network.
. It might be malfunction due to network bandwidth condition or lack of PC
specification.
. Enter DVR designated IP address in internet address
Http//:192.168.1.100:9999
. Under Local Area Network (LAN) between DVR, router and PC, only enter
designated IP address in PC.
. Under Wide Area Network (WAN –internet) the router which was connect
with DVR- it should be Port Forwarding about User Port and Web Port
numbers, then user input the external IP Address & Web port number on
web browser.
. Under Dynamic IP network, to be careful for changeable IP address.
. Dynamic IP user should use provided NVS software or 3G smart phone.
9/16 ch
4 ch
①It is Pop-up message of DVR‟s IP VIEWER.
Please click and download the “Active X”software.
# The Pop Up massage could be different due to different PC OS version.
②Run IP VIEWER software after install DVR View software.
③Indicate connected DVR‟IP address and DVR PORT no. automatically.
④Input desired DVR name and User‟s ID and P/W has to be same as DVR‟s
ID/ PW.
⑤After press CONNECT button, then
can see the Live image.
7. Connecting NVS Network
. Install the NVS Software in the CD according to the Manual and
then open it.
Check
①
②
③
④
⑤
Check
k
④

Quick Manual for 4/9/16CH H.264 DVR
. For Static IP Users
. For DDNS(Dynamic IP) Users
. DVR NAME : Input desired DVR name
. DVR ID : Inputs the DVR‟s ID
. DVR PASS : Inputs the DVR‟s Password
. DVR PORT : Inputs the DVR‟s Use Port number
［CAUTION］You have to do connected Router’s “Use Port number”port forwarding
to proper operation.
. DVR MODEL : Inputs the DVR‟s Channel number.
. USE DDNS : If you select “USE DDNS”, the DDNS set-up would be changed
to “DDNS->115.68.7.22, DDNS PORT->2400”automatically.
［CAUTION］If the articles of “DDNS & DDNS PORT”were set to different numbers, it
may not work well.
. DDNS ID : Inputs the DVR Web Code.
4 Channel 9/16 Channel
. ADD DVR : The DVR would be registered.
# When you click “CONNECT”button, the DVR would be connected.
8. Connecting DMVS(Smart Phone Viewer)
1. Installing “iPhone Program”
Search the “DMVS”in the “App Store”to download and then install it in the
phone.
2. Starting the Program
The Icon is made in the phone if the program is installed
correctly.
Select this Icon to start the program.
3. Applying the Product Information
Input the Network Information to see the DVR via iPhone.
Before using iPhone, the DVR‟s Network menu should be set-up.
Please review the User Manual –Network part at first.
3-1 DVR registration:
After starting the DMVS program, click the “new”
button to register it.
3-2 Input the “Reg. Name”.
Input desired DVR name.
3-3 Input the DVR ID
To connect the DVR remotely, put the Login ID and
Password which were set in the DVR.
3-4 Input the DVR IP (for Static IP Users)
This is only for Static IP Users.
［Reference］After selecting “NO”for “DDNS USE”,
it‟s not saved if you don‟t put the “DVR IP”.
3-5 setting “DDNS USE”
·For Dynamic IP Users, select “YES”.
·For Static IP Users, select “NO”
3-6 Setting DDNS IP (for Dynamic IP Users)
“DDNS IP”is only for Dynamic IP Users so put the
defaults “115.68.7.22”.
3-7 DDNS PORT
If you select above model, “DDNS PORT”is put “2400”automatically.
［CAUTION］Do Not Change this setting.
3-8 Input the “DDNS ID”(For Dynamic IP Users)
“DDNS ID”is own numbers of the DVR. If you find it out on “SYSTEM”Menu, it‟s
indicated with “DDNS ID”or “WEB CODE”. Please put the correct numbers in the MENU.
# It is same as “7. Connecting NVS Network -> For DDNS (Dynamic IP) Users”.
# This is only for Dynamic Users, so don‟t need to input if you‟re Static IP Users.
3-9 Connecting
After finish to register, please press “Add”button on top-right side.
If you press Reg. Name of DVR, it will ask you if you want to “Connect”or “No”.
Web
Code

Quick Manual for 4/9/16CH H.264 DVR
Then select “Connect”button and go into the DVR.