RHINO RHINO 2409 User manual

F-3676 Page 1 of 4 1-7-2005
ASSEMBLY MANUAL 2-7126
Keep with Operator’s Manual
LOADER MOUNTING KIT
2409 LOADER
NEW HOLLAND TRACTORS
MODEL 2WD FWA ROPS SOFT CAB
2120 After S/N UV32236 X X X X
3415 X X X X
TRACTOR AND MOUNTING KIT GENERAL
INFORMATION
Mounting kit can be installed on tractor using tools
ordinarily available.
IMPORTANT: This mounting kit is compatible with
vertical exhaust only. Mounting kit is not compatible
with front weights. If tractor is equipped with front
weights, they must be removed before mounting
loader. It is not necessary to remove front weight
bracket.
NOTE: If installing optional grille guard (2-6225), install
grille guard and front mounting bracket (1, Figure 1) at
same time.
Check tire clearances when loader installation is
complete and adjust tread width as necessary to
provide adequate clearance.
Shut off tractor engine and engage parking brakes
during installation.
INSTALLING LOADER MOUNTING BRACKETS
(Figure 1)
NOTE: Install all attaching hardware loosely (unless
noted otherwise) until mounting kit is completely
assembled to facilitate assembly and proper alignment.
Tighten all hardware to torques specified in general
torque specifications table.
1. Attach front mounting bracket (1) to sides of tractor
front frame using 1/2 x 2" cap screws (10) and lock
nuts (14).
2. Support tractor auxiliary valve and bracket and
remove four 16mm cap screws which secure valve
bracket (A) to mounting pad on right side of tractor
clutch housing. Support right side of tractor engine
and front frame and remove five 14mm cap screws
from tractor frame and engine casting ahead of
mounting pad.
3. With valve bracket sandwiched between, fasten
right mid mounting bracket (3) to tractor clutch
housing using four 16mm x 50 mm cap screws (8)
and 5/8" lock washers (11), and with tractor front
frame to engine block using five 14mm x 55mm cap
screws (9) and 9/16" lock washers (12).
4. Support left side of tractor engine and front frame
and remove five 14mm cap screws from tractor
frame ahead of mounting pad.
5. Fasten left mid mounting bracket (2) and spacer
plate (6) to tractor clutch housing using four 16mm
x 50 cap screws (8) and 5/8" lock washers (11) and
with tractor front frame to engine block using five
14mm x 55mm cap screws (9) and 9/16" lock
washers (12).
NOTE: Tighten 16mm cap screws (8) to 130-158 ft.·lbs.
of torque. Tighten 14mm cap screws (9) to 85-103
ft.·lbs. of torque.
MOUNTING LOADER ONTO TRACTOR AND
MOUNTING BRACKETS
WARNING: To avoid injury during
installation of quick attach loader, do not
permit bystanders within ten feet of loader
or tractor.
1. Loop chain under each lift cylinder and hook on
loader boom arm. Using overhead hoist to support
loader, remove hardware securing loader to pallet.
Lift loader and remove pallet.
CAUTION: Do not damage grease fitting
on end of cylinder. Be sure chain does not
pinch lift cylinder.
2. Using overhead hoist, lower loader from vertical
shipping position to horizontal position, leaving
enough room to install yoke. (Scraps of cardboard
may be used to protect paint.) Fasten yoke
assembly (4) to loader side frames using 3/4 x 2-
1/2" cap screws (7) and lock nuts (13).

1-7-2005 Page 2 of 4 F-3676
2-7126
NOTE: Hardware connecting yoke to loader side
frames should be snug, but do not tighten
completely. After loader has been mounted to
tractor and aligned with mid mounting brackets and
front mounting bracket, tighten 3/4-10 Grade 5
hardware to 238-262 ft.·lbs. of torque.
3. Install hose or valve kit to tractor and loader. Refer
to instructions provided with hose or valve kit.
4, Reposition overhead hoist by looping nylon strap
around yoke near loader side frames at balance
point of loader.
5. Using overhead hoist, raise loader until side frame
uprights will clear front tires. Remove lock nut and
washer from loader hinge and swing each hinge
open.
6. Position loader so hinges hook over mid mounting
tubes and yoke tube fits inside of front mounting
bracket.
7. Clamp hinges to mid mounting tubes with 3/4" flat
washers and 3/4" flex-lock nuts (supplied with
loader).
IMPORTANT: Be sure to use flex-lock nuts to
clamp hinge. Tighten flex-lock nuts against hinge
securely, but not to more than 125 ft.·lbs. of torque.
8. Adjust front wheel tread or steering stops, if
necessary, to prevent interference between tires
and loader. Refer to tractor operator’s manual for
adjustment procedures.
Balance point
of loader
Hinge open
PARTS LIST – LOADER MOUNTING KIT
Item Part No. Description Qty.
1 50060 BRACKET, Mounting, Front 1
2 50063 BRACKET, Mounting, Mid, Left 1
3 50062 BRACKET, Mounting, Mid, Right 1
4 44124 BRACKET, Front Yoke 1
5 39240 DECAL, WARNING: Do Not Use For Towing 2
6 43124 SPACER, Plate, Left 1
7 41838-15 SCREW, Cap, 3/4-10 x 2-1/4", Grade 5 4
8 42672-12 SCREW, Cap, 16mm-2.00 x 50mm Class 8.8 8
9 42672-22 SCREW, Cap, 14mm-1.50 x 55mm Class 8.8 10
10 41838-13 SCREW, Cap, 1/2-13 x 2" Grade 5 6
11 41837-7 WASHER, Lock, 5/8" 8
12 41837-6 WASHER, Lock, 9/16" 10
13 41840-8 NUT, Lock, 3/4-10, Type N 4
14 41840-5 NUT, Lock, 1/2-13, Type N 6

F-3676 Page 3 of 4 1-7-2005
2-7126
811 2
912
1
6
3
8
811 912
11
13
5
NOTE: Support tractor engine
and front frame and remove
five cap screws, one side at a
time, to fasten mid mounting
brackets (2 & 3) to tractor
front frame and engine block.
7
10
10
14
4
(A)
DO NOT USE FOR TOWING
TOWING HERE WILL PULL FRONT
LOADER SUPPORT OUT OF POCKET
CAUSING DAMAGE AND POSSIBLE
INJURY.
WARNING
39240
Figure 1
Loader Mounting Kit

1-7-2005 Page 4 of 4 F-3676
2-7126
AMERICAN STANDARD CAP SCREWS METRIC CAP SCREWS
GENERAL TORQUE SPECIFICATIONS
USE THE FOLLOWING TORQUES WHEN SPECIAL TORQUES ARE NOT GIVEN
SAE Grade
Typ. Head
Markings
Metric Class
Typ. Head
Markings
5 8 8.8 10.9
Cap Screw TORQUE TORQUE TORQUE TORQUE
Size FT·LBS N·m FT·LBS N·m FT·LBS N·m FT·LBS N·m
Inches MIN MAX MIN MAX MIN MAX MIN MAX
6.25 7.25 8.5 10 8.25 9.5 11 13
8 9 11 12 10.5 12 14 16
14 15 19 20 18.5 20 25 27
17.5 19 23 26 23 25 31 34
26 28 35 38 35 37 47.5 50
31 34 42 46 41 45 55.5 61
41 45 55.5 61 55 60 74.5 81
51 55 69 74.5 68 75 92 102
65 72 88 97.5 86 96 116 130
76 84 103 114 102 112 138 152
95 105 129 142 127 140 172 190
111 123 150 167 148 164 200 222
126 139 171 188 168 185 228 251
152 168 206 228 203 224 275 304
238 262 322 355 318 350 431 474
274 305 371 409 365 402 495 544
350 386 474 523 466 515 631 698
407 448 551 607 543 597 736 809
537 592 728 802 716 790 970 1070
670 740 908 1003 894 987 1211 1337
MIN MAX MIN MAX MIN MAX MIN MAX
688119111215
16 20 21.5 27 23 27 31 36.5
29 35 39 47 42 52 57 70
52 62 70 84 75 91 102 123
85 103 115 139 120 146 163 198
130 158 176 214 176 216 238 293
172 210 233 284 240 294 325 398
247 301 335 408 343 426 465 577
332 404 450 547 472 576 639 780
423 517 573 700 599 732 812 992
637 779 863 1055 898 1098 1217 1488
872 1066 1181 1444 1224 1496 1658 2027
1/4 - 20
1/4 - 28
5/16 - 18
5/16 - 24
3/8 - 16
3/8 - 24
7/16 - 14
7/16 - 20
1/2 - 13
1/2 - 20
9/16 - 12
9/16 - 18
Cap Screw
Size
Millimeters
M6 x 1.00
M8 x 1.25
M10 x 1.50
M12 x 1.75
M14 x 2.00
M16 x 2.50
M18 x 2.50
M20 x 2.50
M22 x 2.50
M24 x 3.00
M27 x 3.00
M30 x 3.00
5/8 - 11
5/8 - 18
3/4 - 10
3/4 - 16
7/8 - 9
7/8 - 14
1 - 8
1 - 14
Standard American and Metric Cap Screws
NOTE: These values apply to fasteners as received
from supplier, dry or when lubricated with normal
engine oil. They do not apply if special graphite or
molysulphide greases or other extreme lubricants are
used.
INSTALLING BUCKET OR ATTACHMENT
Refer to instructions provided with bucket or
attachment to install.
INSTALLING LEVEL INDICATOR
1. Attach indicator guide tube to cylinder pin. Guide
tube is positioned to outside of boom.
2. Slide level indicator rod through guide tube. Attach
other end of rod with 1/8 x 1" cotter pins and 3/8" flat
washers.
3. Locate tractor and loader on level surface. With
bottom of bucket resting on surface, cut off excess
rod flush with end of guide tube or paint exposed
rod a contrasting color.
Level Indicator for
Pin-On Buckets
or Attachments
Indicator
Guide
Tu b e Loader Right
Boom Arm
Cotter Pins
Flat Washers
Indicato
r
Rod
INSTALLATION
INSTRUCTIONS